The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current code sets an infinite timeout on SG_IO requests,
causing the guest to stall if the host experiences a frame
loss.
This patch adds an 'io_timeout' parameter for SCSIDevice to
make the SG_IO timeout configurable, and also shortens the
default timeout to 30 seconds to avoid infinite stalls.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add scsi_device_get which finds the scsi device
and takes a reference to it.
Suggested-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200913160259.32145-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-12-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
We will need to add LCHS removal logic to scsi-hd's unrealize() in the
next commit.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
There is no DMA in Quadra 800, so the CPU reads/writes the data from the
PDMA register (offset 0x100, ESP_PDMA in hw/m68k/q800.c) and copies them
to/from the memory.
There is a nice assembly loop in the kernel to do that, see
linux/drivers/scsi/mac_esp.c:MAC_ESP_PDMA_LOOP().
The start of the transfer is triggered by the DREQ interrupt (see linux
mac_esp_send_pdma_cmd()), the CPU polls on the IRQ flag to start the
transfer after a SCSI command has been sent (in Quadra 800 it goes
through the VIA2, the via2-irq line and the vIFR register)
The Macintosh hardware includes hardware handshaking to prevent the CPU
from reading invalid data or writing data faster than the peripheral
device can accept it.
This is the "blind mode", and from the doc:
"Approximate maximum SCSI transfer rates within a blocks are 1.4 MB per
second for blind transfers in the Macintosh II"
Some references can be found in:
Apple Macintosh Family Hardware Reference, ISBN 0-201-19255-1
Guide to the Macintosh Family Hardware, ISBN-0-201-52405-8
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-4-laurent@vivier.eu>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 1800 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h, down from 5400 due to the
previous commit).
Several headers include sysemu/sysemu.h just to get typedef
VMChangeStateEntry. Move it from sysemu/sysemu.h to qemu/typedefs.h.
Spell its structure tag the same while there. Drop the now
superfluous includes of sysemu/sysemu.h from headers.
Touching sysemu/sysemu.h now recompiles some 1100 objects.
qemu/uuid.h also drops from 1800 to 1100, and
qapi/qapi-types-run-state.h from 5000 to 4400.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-29-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This makes use of qdev_prop_drive_iothread for scsi-disk so that the
disk can be attached to a node that is already in the target AioContext.
We need to check that the HBA actually supports iothreads, otherwise
scsi-disk must make sure that the node is already in the main
AioContext.
This changes the error message for conflicting iothread settings.
Previously, virtio-scsi produced the error message, now it comes from
blk_set_aio_context(). Update a test case accordingly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Emulation of the block limits VPD page called back into scsi-disk.c,
which however expected the request to be for a SCSIDiskState and
accessed a scsi-generic device outside the bounds of its struct
(namely to retrieve s->max_unmap_size and s->max_io_size).
To avoid this, move the emulation code to a separate function that
takes a new SCSIBlockLimits struct and marshals it into the VPD
response format.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The VPD Block Limits Inquiry page is optional, allowing SCSI devices
to not implement it. This is the case for devices like the MegaRAID
SAS 9361-8i and Microsemi PM8069.
In case of SCSI passthrough, the response of this request is used by
the QEMU SCSI layer to set the max_io_sectors that the guest
device will support, based on the value of the max_sectors_kb that
the device has set in the host at that time. Without this response,
the guest kernel is free to assume any value of max_io_sectors
for the SCSI device. If this value is greater than the value from
the host, SCSI Sense errors will occur because the guest will send
read/write requests that are larger than the underlying host device
is configured to support. An example of this behavior can be seen
in [1].
A workaround is to set the max_sectors_kb host value back in the guest
kernel (a process that can be automated using rc.local startup scripts
and the like), but this has several drawbacks:
- it can be troublesome if the guest has many passthrough devices that
needs this tuning;
- if a change in max_sectors_kb is made in the host side, manual change
in the guests will also be required;
- during an OS install it is difficult, and sometimes not possible, to
go to a terminal and change the max_sectors_kb prior to the installation.
This means that the disk can't be used during the install process. The
easiest alternative here is to roll back to scsi-hd, install the guest
and then go back to SCSI passthrough when the installation is done and
max_sectors_kb can be set.
An easier way would be to QEMU handle the absence of the Block Limits
VPD device response, setting max_io_sectors accordingly and allowing
the guest to use the device without the hassle.
This patch adds emulation of the Block Limits VPD response for
SCSI passthrough devices of type TYPE_DISK that doesn't support
it. The following changes were made:
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply. In case the device does not
- a new function called scsi_generic_set_vpd_bl_emulation,
that is called during device realize, was created to set a
new flag 'needs_vpd_bl_emulation' of the device. This function
retrieves the Inquiry EVPD response of the device to check for
VPD BL support.
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply in case the device needs
VPD BL emulation, adding the Block Limits page (0xb0) to
the list. This will make the guest kernel aware of the
support that we're now providing by emulation.
- a new function scsi_emulate_block_limits creates the
emulated Block Limits response. This function is called
inside scsi_read_complete in case the device requires
Block Limits VPD emulation and we detected a SCSI Sense
error in the VPD Block Limits reply that was issued
from the guest kernel to the device. This error is
expected: we're reporting support from our side, but
the device isn't aware of it.
With this patch, the guest now queries the Block Limits
page during the device configuration because it is being
advertised in the Supported Pages response. It will either
receive the Block Limits page from the hardware, if it supports
it, or will receive an emulated response from QEMU. At any rate,
the guest now has the information to set the max_sectors_kb
parameter accordingly, sparing the user of SCSI sense errors
that would happen without the emulated response and in the
absence of Block Limits support from the hardware.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-4-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the VPD Block Limits emulation with SCSI passthrough,
we'll issue an Inquiry request with EVPD set to retrieve
the available VPD pages of the device. This would be done in
a way similar of what scsi_generic_read_device_identification
does: create a SCSI command and a reply buffer, fill in the
sg_io_hdr_t structure, call blk_ioctl, check if an error
occurred, process the response.
This same process is done in other 2 functions, get_device_type
and get_stream_blocksize. They differ in the command/reply
buffer and post-processing, everything else is almost a
copy/paste.
Instead of adding a forth copy/pasted-ish code when adding
the passthrough VPD BL emulation, this patch extirpates
this repetition of those 3 functions and put it into
a new one called scsi_SG_IO_FROM_DEV. Any future code that
wants to execute an SG_DXFER_FROM_DEV to the device can
use it, avoiding filling sg_io_hdr_t again and et cetera.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-3-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To add support for the emulation of Block Limits VPD page
for passthrough devices, a few adjustments in the current code
base is required to avoid repetition and improve clarity.
In scsi-generic.c, detach the Inquiry handling from
scsi_read_complete and put it into a new function called
scsi_handle_inquiry_reply. This change aims to avoid
cluttering of scsi_read_complete when we more logic in the
Inquiry response handling is added in the next patches,
centralizing the changes in the new function.
In scsi-disk.c, take the build of all emulated VPD pages
from scsi_disk_emulate_inquiry and make it available to
other files into a non-static function called
scsi_disk_emulate_vpd_page. Making it public will allow
the future VPD BL emulation code for passthrough devices
to use it from scsi-generic.c, avoiding copy/pasting this
code solely for that purpose. It also has the advantage of
providing emulation of all VPD pages in case we need to
emulate other pages in other scenarios. As a bonus,
scsi_disk_emulate_inquiry got tidier.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-2-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Automatic creation of SCSI controllers for "-drive if=scsi" for x86
machines was quite a bad idea (see description of commit f778a82f0c
for details). This is marked as deprecated since QEMU v2.9.0, and as
far as I know, nobody complained that this is still urgently required
anymore. Time to remove this now.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1519123357-13225-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because usb-storage creates an internal scsi device, we should propagate
options. We already do so for bootindex etc, but failed to take care of
share-rw. Fix it in an apparent way: add a new parameter to
scsi_bus_legacy_add_drive and pass in s->conf.share_rw.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20180117005222.4781-1-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This enables them to be used outside of esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
util/scsi.c includes some SCSI code that is shared by block/iscsi.c and
hw/scsi, but the introduction of the persistent reservation helper
will add many more instances of this. There is also include/block/scsi.h,
which actually is not part of the core block layer.
The persistent reservation manager will also need a home. A scsi/
directory provides one for both the aforementioned shared code and
the PR manager code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After introducing the scsi/ subdirectory, there will be a scsi_build_sense
function that is the same as scsi_req_build_sense but without needing
a SCSIRequest. The existing scsi_build_sense function gets in the way,
remove it.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Block backends defined with "-drive if=T" with T other than "none" are
meant to be picked up by machine initialization code: a suitable
frontend gets created and wired up automatically.
Drives defined with if=scsi are also picked up by SCSI HBAs added with
-device, unlike other interface types. Deprecate this usage, as follows.
Create the frontends for onboard HBAs in machine initialization code,
exactly like we do for if=ide and other interface types. Change
scsi_legacy_handle_cmdline() to create a frontend only when it's still
missing, and warn that this usage is deprecated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-3-git-send-email-armbru@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
Unused function declarations were found using a simple gcc plugin and
manually verified by grepping the sources.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Scanners can provide additional sense bytes beyond 18 bytes.
VueScan uses 32 bytes alloc length with Request Sense command.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@iki.fi>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While doing DMA read into ESP command buffer 's->cmdbuf', it could
write past the 's->cmdbuf' area, if it was transferring more than 16
bytes. Increase the command buffer size to 32, which is maximum when
's->do_cmd' is set, and add a check on 'len' to avoid OOB access.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-run scripts/clean-includes to apply the previous commit's
corrections and updates. Besides redundant qemu/typedefs.h, this only
finds a redundant config-host.h include in ui/egl-helpers.c. No idea
how that escaped the previous runs.
Some manual whitespace trimming around dropped includes squashed in.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SAS adapters need to access them in order to publish the SAS addresses
of the end devices connected to them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Function has been deleted in ad2d30f79d.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
