Currently the ISA devices that are part of the VIA south bridge,
superio chip are wired up by board code. Move creation of these ISA
devices to the VIA ISA bridge model so that board code does not need
to access ISA bus. This also allows vt82c686b-superio to be made
internal to vt82c686 which allows implementing its configuration via
registers in subseqent commits.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <bf9400cc8e4ddd3129aa5678de4d3cf38384805f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove unneeded variables and setting value to 0 on zero initialised
data and replace check for error with error_fatal. Rationalise loop
that sets PCI config header fields read only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <e4caf35ca10a68f5c74ae3f93fa0bcfa9457beea.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This device is part of the multifunction VIA superio/south bridge chip
so not useful in itself.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <d0a806fed5e8055aee4fcf5b2f4790e6dd0f9dc6.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per core ISR is a set of 32-bit registers spaced by 8 bytes.
This patch fixed calculation of it's size and also added check
of alignment at reading & writing.
Fixes: Coverity CID 1438965 and CID 1438967
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20210112012527.28927-1-jiaxun.yang@flygoat.com>
[PMD: Added Coverity CID]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Translate embedded assembly into IO writes which is more
readable.
Also hardcode cm_base at boot time instead of reading from CP0.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-5-jiaxun.yang@flygoat.com>
[PMD: Kept code comments]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here boston)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here fuloong2e)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add a bootloader helper to generate simple bootloaders for kernel.
It can help us reduce inline hex hack and also keep MIPS release 6
compatibility easier.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-2-jiaxun.yang@flygoat.com>
[PMD: Restricted bl_reg enum to C source,
inverted bl_gen_write() args,
added license in hw/mips/bootloader.h]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the loongson3 defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210122122404.11970-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----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=ipHI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial patches 20210220
# gpg: Signature made Sat 20 Feb 2021 12:34:21 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
MAINTAINERS: Fix default-configs/ entries
target/avr/cpu: Use device_class_set_parent_realize()
hw/scsi/megasas: Remove pointless parenthesis
u2f-passthru: put it into the 'misc' category
tpm: put some tpm devices into the correct category
nvdimm: put it into the 'storage' category
vmmouse: put it into the 'input' category
virtio-pmem: put it into the 'storage' category
MAINTAINERS: add my github tree URL
Fix SPDX-License-Identifier typos
hw/block/fdc: Remove the check_media_rate property
hw/i386/xen: Remove dead code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The category of the u2f-passthru device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20201130083630.2520597-10-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Some tpm devices have no category, put them into the correct category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20201130083630.2520597-8-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the nvdimm device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-5-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the vmmouse device is not set, put it into the 'input'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-4-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the virtio-pmem device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Message-Id: <20201130083630.2520597-3-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This was only required for the pc-1.0 and earlier machine types.
Now that these have been removed, we can also drop the corresponding
code from the FDC device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20210203171832.483176-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'drivers_blacklisted' is never accessed, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20210202155644.998812-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
s->prnsts is updated in both branches of the if () else () statement.
Move the common bits outside so that it is cleaner.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1613447214-81951-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Unlike SD mode, when SD card is working in SPI mode, the argument
of CMD13 is stuff bits. Hence we should bypass the RCA check.
See "Physical Layer Specification Version 8.00", chapter 7.3.1.3
Detailed Command Description (SPI mode):
"The card shall ignore stuff bits and reserved bits in an argument"
and Table 7-3 Commands and Arguments (SPI mode):
"CMD13 Argument [31:0] stuff bits"
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in CMD24/25 for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in sd_erase() for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These APIs and macros may be referenced by functions that are
currently before them. Move them ahead a little bit.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, CMD30
response type is R1, not R1b.
Fixes: a1bb27b1e9 ("SD card emulation initial implementation")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, the
following commands:
- CMD28 (SET_WRITE_PROT)
- CMD29 (CLR_WRITE_PROT)
- CMD30 (SEND_WRITE_PROT)
are only supported by SDSC cards.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For high capacity memory cards, the erase start address and end
address are multiplied by 512, but the address check is still
based on the original block number in sd->erase_{start, end}.
Fixes: 1bd6fd8ed5 ("hw/sd/sdcard: Do not attempt to erase out of range addresses")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Besides CMD12, the following command's reponse type is R1b:
- SET_WRITE_PROT (CMD28)
- CLR_WRITE_PROT (CMD29)
- ERASE (CMD38)
Reuse the same s->stopping to indicate a R1b reponse is needed.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
CMD12's response type is R1b, which is basically a R1 plus optional
addition of the busy signal token that can be any number of bytes.
A zero value indicates card is busy and a non-zero value indicates
the card is ready for the next command.
Current implementation sends the busy signal token without sending
the R1 first. This does not break the U-Boot/Linux mmc_spi driver,
but it does not make the VxWorks driver happy.
Move the testing logic of s->stopping in the SSI_SD_RESPONSE state
a bit later, after the first byte of the card reponse is sent out,
to conform with the spec. After the busy signal token is sent, the
state should be transferred to SSI_SD_CMD.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210128063035.15674-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The SEND_IF_COND command (CMD8) response is of format R7, but
current code returns R1 for CMD8. Fix it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For a multiple block write operation, each block begins with a multi
write start token. Unlike the SD mode that the multiple block write
ends when receiving a STOP_TRAN command (CMD12), a special stop tran
token is used to signal the card.
Emulating this by manually sending a CMD12 to the SD card core, to
bring it out of the receiving data state.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-7-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add 2 more states for the block write operation. The SPI host needs
to send a data start token to start the transfer, and the data block
written to the card will be acknowledged by a data response token.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 6 -> 7]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present there is a data_ready() callback for the SD data read
path. Let's add a receive_ready() for the SD data write path.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the single/multiple block write in SPI mode is blocked
by sd_normal_command(). Remove the limitation.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The single block read (CMD17) codes are the same as the multiple
block read (CMD18). Merge them into one. The same applies to single
block write (CMD24) and multiple block write (CMD25).
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In the case of a multiple block read operation every transferred
block has its suffix of CRC16. Update the state machine logic to
handle multiple block read.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 5 -> 6]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When viewing/debugging memory regions it is sometimes hard to figure
out which PCI device something belongs to. Make the names unique by
including the vdev name in the name string.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210213130325.14781-2-alex.bennee@linaro.org>
Without that wireshark complains about invalid control setup data
for non-control transfers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210216144939.841873-1-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In order to keep track of the alternate setting that should be used for
a given interface, the USBDevice struct keeps an array of alternate
setting values, which is indexed by the interface number. In
usb_host_set_interface, when this array is updated, usb_host_ep_update
is called as a result. However, when usb_host_ep_update accesses the
active libusb_config_descriptor, it indexes udev->altsetting with the
loop variable, rather than the interface number.
With the simple trace backend enable, this behavior can be seen:
[...]
usb_xhci_xfer_start 0.440 pid=1215 xfer=0x5596a4b85930 slotid=0x1 epid=0x1 streamid=0x0
usb_packet_state_change 1.703 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'undef' n=b'setup'
usb_host_req_control 2.269 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 req=0x10b value=0x1 index=0xd
usb_host_set_interface 0.449 pid=1215 bus=0x1 addr=0x5 interface=0xd alt=0x1
usb_host_parse_config 2542.648 pid=1215 bus=0x1 addr=0x5 value=0x2 active=0x1
usb_host_parse_interface 1.804 pid=1215 bus=0x1 addr=0x5 num=0xc alt=0x0 active=0x1
usb_host_parse_endpoint 2.012 pid=1215 bus=0x1 addr=0x5 ep=0x2 dir=b'in' type=b'int' active=0x1
usb_host_parse_interface 1.598 pid=1215 bus=0x1 addr=0x5 num=0xd alt=0x0 active=0x1
usb_host_req_emulated 3.593 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 status=0x0
usb_packet_state_change 2.550 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'setup' n=b'complete'
usb_xhci_xfer_success 4.298 pid=1215 xfer=0x5596a4b85930 bytes=0x0
[...]
In particular, it is seen that although usb_host_set_interface sets the
alternate setting of interface 0xd to 0x1, usb_host_ep_update uses 0x0
as the alternate setting due to using the incorrect index to
udev->altsetting.
Fix this problem by getting the interface number from the active
libusb_config_descriptor, and then using that as the index to
udev->altsetting.
Signed-off-by: Nick Rosbrook <rosbrookn@ainfosec.com>
Message-Id: <20210201213021.500277-1-rosbrookn@ainfosec.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When SEV-ES is enabled, it is not possible modify the guests register
state after it has been initially created, encrypted and measured.
Normally, an INIT-SIPI-SIPI request is used to boot the AP. However, the
hypervisor cannot emulate this because it cannot update the AP register
state. For the very first boot by an AP, the reset vector CS segment
value and the EIP value must be programmed before the register has been
encrypted and measured. Search the guest firmware for the guest for a
specific GUID that tells Qemu the value of the reset vector to use.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <22db2bfb4d6551aed661a9ae95b4fdbef613ca21.1611682609.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux blkfront expects both "discard-granularity" and
"discard-alignment" present on xenbus in order to properly enable the
feature, not exposing "discard-alignment" left some Linux blkfront
versions with a broken discard setup. This has also been addressed in
Linux with:
https://lore.kernel.org/lkml/20210118151528.81668-1-roger.pau@citrix.com/T/#u
Fix QEMU to report a "discard-alignment" of 0, in order for it to work
with older Linux frontends.
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Message-Id: <20210118153330.82324-1-roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
cmd_fis is mapped as DMA_DIRECTION_FROM_DEVICE, however, it is read
from, and not written to anywhere. Fix the DMA_DIRECTION and mark
cmd_fis as read-only in the code.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210119164051.89268-1-alxndr@bu.edu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Copy bootinfo.h and bootinfo-mac.h from arch/m68k/include/uapi/asm/
to include/standard-headers/asm-m68k/
Imported from linux v5.9 but didn't change since v4.14 (header update)
and since v4.10 (content update).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201220112615.933036-2-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Use nr_apu_cpus in favor of hard coding 2.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210210142048.3125878-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
nvme_ns_realize passes errp to nvme_register_namespaces, but then try to
prepend errp with local_err.
Just remove the local_err and use errp directly.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Current QEMU HEAD nvme.c does not compile with the default GCC 5.4
on a Ubuntu 16.04 host:
hw/block/nvme.c:3242:9: error: ‘result’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
trace_pci_nvme_getfeat_vwcache(result ? "enabled" : "disabled");
^
hw/block/nvme.c:3150:14: note: ‘result’ was declared here
uint32_t result;
^
Explicitly initialize the result to fix it.
Fixes: aa5e55e3b0 ("hw/block/nvme: open code for volatile write cache")
Fixes: Coverity CID 1446371
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Moving namespace registration to the nvme-ns realization function had
the unintended side-effect of breaking legacy namespace registration.
Fix this.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Reported-by: Alexander Graf <agraf@csgraf.de>
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
NPCM7XX GPIO devices have been implemented in hw/gpio/npcm7xx-gpio.c. So
we removed them from the unimplemented devices list.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu<wuhaotsh@google.com>
Message-id: 20210129005845.416272-2-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Perform device reset in the remote process when QEMU performs
device reset. This is required to reset the internal state
(like registers, etc...) of emulated devices
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7cb220a51f565dc0817bd76e2f540e89c2d2b850.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Retrieve PCI configuration info about the remote device and
configure the Proxy PCI object based on the returned information
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 85ee367bbb993aa23699b44cfedd83b4ea6d5221.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IOHUB object is added to manage PCI IRQs. It uses KVM_IRQFD
ioctl to create irqfd to injecting PCI interrupts to the guest.
IOHUB object forwards the irqfd to the remote process. Remote process
uses this fd to directly send interrupts to the guest, bypassing QEMU.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 51d5c3d54e28a68b002e3875c59599c9f5a424a1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add ProxyMemoryListener object which is used to keep the view of the RAM
in sync between QEMU and remote process.
A MemoryListener is registered for system-memory AddressSpace. The
listener sends SYNC_SYSMEM message to the remote process when memory
listener commits the changes to memory, the remote process receives
the message and processes it in the handler for SYNC_SYSMEM message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 04fe4e6a9ca90d4f11ab6f59be7652f5b086a071.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Proxy device object implements handler for PCI BAR writes and reads.
The handler uses BAR_WRITE/BAR_READ message to communicate to the
remote process with the BAR address and value to be written/read.
The remote process implements handler for BAR_WRITE/BAR_READ
message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: a8b76714a9688be5552c4c92d089bc9e8a4707ff.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The Proxy Object sends the PCI config space accesses as messages
to the remote process over the communication channel
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d3c94f4618813234655356c60e6f0d0362ff42d6.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d54edb4176361eed86b903e8f27058363b6c83b3.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines a PCI Device proxy object as a child of TYPE_PCI_DEVICE.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: b5186ebfedf8e557044d09a768846c59230ad3a7.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
SyncSysMemMsg message format is defined. It is used to send
file descriptors of the RAM regions to remote device.
RAM on the remote device is configured with a set of file descriptors.
Old RAM regions are deleted and new regions, each with an fd, is
added to the RAM.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7d2d1831d812e85f681e7a8ab99e032cf4704689.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Associate the file descriptor for a PCIDevice in remote process with
DeviceState object.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: f405a2ed5d7518b87bea7c59cfdf334d67e5ee51.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Initializes the message handler function in the remote process. It is
called whenever there's an event pending on QIOChannel that registers
this function.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 99d38d8b93753a6409ac2340e858858cda59ab1b.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines MPQemuMsg, which is the message that is sent to the remote
process. This message is sent over QIOChannel and is used to
command the remote process to perform various tasks.
Define transmission functions used by proxy and by remote.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 56ca8bcf95195b2b195b08f6b9565b6d7410bce5.1611938319.git.jag.raman@oracle.com
[Replace struct iovec send[2] = {0} with {} to make clang happy as
suggested by Peter Maydell <peter.maydell@linaro.org>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
x-remote-machine object sets up various subsystems of the remote
device process. Instantiate PCI host bridge object and initialize RAM, IO &
PCI memory regions.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c537f38d17f90453ca610c6b70cf3480274e0ba1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
PCI host bridge is setup for the remote device process. It is
implemented using remote-pcihost object. It is an extension of the PCI
host bridge setup by QEMU.
Remote-pcihost configures a PCI bus which could be used by the remote
PCI device to latch on to.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 0871ba857abb2eafacde07e7fe66a3f12415bfb2.1611938319.git.jag.raman@oracle.com
[Added PCI_EXPRESS condition in hw/remote/Kconfig since remote-pcihost
needs PCIe. This solves "make check" failure on s390x. Fix suggested by
Philippe Mathieu-Daudé <philmd@redhat.com> and Thomas Huth
<thuth@redhat.com>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Per MPC8548ERM [1] chapter 14.5.3.4.1:
When RCTRL.RSF is 1, frames less than 64 bytes are accepted upon
a DA match. But currently QEMU does the opposite. This commit
reverses the RCTRL.RSF testing logic to match the manual.
Due to the reverse of the logic, certain guests may potentially
break if they don't program eTSEC to have RCTRL.RSF bit set.
When RCTRL.RSF is 0, short frames are silently dropped, however
as of today both slirp and tap networking do not pad short frames
(e.g.: an ARP packet) to the minimum frame size of 60 bytes. So
ARP requests will be dropped, preventing the guest from becoming
visible on the network.
The same issue was reported on e1000 and vmxenet3 before, see:
commit 78aeb23ede ("e1000: Pad short frames to minimum size (60 bytes)")
commit 40a87c6c9b ("vmxnet3: Pad short frames to minimum size (60 bytes)")
[1] https://www.nxp.com/docs/en/reference-manual/MPC8548ERM.pdf
Fixes: eb1e7c3e51 ("Add Enhanced Three-Speed Ethernet Controller (eTSEC)")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <1612923021-19746-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the <clock-frequency> property of the serial node is
populated with value zero. U-Boot's ns16550 driver is not happy
about this, so let's fill in a meaningful value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1612362288-22216-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the platform clock frequency is using a magic number.
Convert it to a macro and use it everywhere.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1612362288-22216-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current logic for calculating 'maxdomain' making it a sum of
numa_state->num_nodes with spapr->gpu_numa_id. spapr->gpu_numa_id is
used as a index to determine the next available NUMA id that a
given NVGPU can use.
The problem is that the initial value of gpu_numa_id, for any topology
that has more than one NUMA node, is equal to numa_state->num_nodes.
This means that our maxdomain will always be, at least, twice the
amount of existing NUMA nodes. This means that a guest with 4 NUMA
nodes will end up with the following max-associativity-domains:
rtas/ibm,max-associativity-domains
00000004 00000008 00000008 00000008 00000008
This overtuning of maxdomains doesn't go unnoticed in the guest, being
detected in SLUB during boot:
dmesg | grep SLUB
[ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=8
SLUB is detecting 8 total nodes, with 4 nodes being online.
This patch fixes ibm,max-associativity-domains by considering the amount
of NVGPUs NUMA nodes presented in the guest, instead of just
spapr->gpu_numa_id.
Reported-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-4-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We'll need to check the initial value given to spapr->gpu_numa_id when
building the rtas DT, so put it in a helper for easier access and to
avoid repetition.
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is used only in spapr_numa.c.
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This to map the PNOR from the machine init handler directly and finish
the cleanup of the LPC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-8-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On PowerNV systems, the BMC is in charge of mapping the PNOR contents
on the LPC FW address space using the HIOMAP protocol. Under QEMU, we
emulate this behavior and we also add an extra control on the flash
accesses by letting the HIOMAP command handler decide whether the
memory region is accessible or not depending on the firmware requests.
However, this behavior is not compatible with hostboot like firmwares
which need this mapping to be always available. For this reason, the
PNOR memory region is initially disabled for skiboot mode only.
This is badly placed under the LPC model and requires the use of the
machine. Since it doesn't add much, simply remove the initial setting.
The extra control in the HIOMAP command handler will still be performed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-7-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine can be run with an external IPMI BMC device
connected to a remote QEMU machine acting as BMC, using these options :
-chardev socket,id=ipmi0,host=localhost,port=9002,reconnect=10 \
-device ipmi-bmc-extern,id=bmc0,chardev=ipmi0 \
-device isa-ipmi-bt,bmc=bmc0,irq=10 \
-nodefaults
In that case, some aspects of the BMC initialization should be
skipped, since they rely on the simulator interface.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-6-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
and reuse pnv_bmc_set_pnor() to share the setting of the PNOR.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current settings are useful to load large kernels (with debug) but
it moves the initrd image in a memory region not protected by
skiboot. If skiboot is compiled with DEBUG=1, memory poisoning will
corrupt the initrd.
Cc: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-4-clg@kaod.org>
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ENDs allocated by OPAL for the HW thread VPs are tagged as owned by FW.
Dump the state in 'info pic'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9 systems, PHB controllers signal the XIVE interrupt controller
of a source interrupt notification using a store on a MMIO region. Add
traces for such events.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently not possible to perform a strict boot from USB storage:
$ qemu-system-ppc64 -accel kvm -nodefaults -nographic -serial stdio \
-boot strict=on \
-device qemu-xhci \
-device usb-storage,drive=disk,bootindex=0 \
-blockdev driver=file,node-name=disk,filename=fedora-ppc64le.qcow2
SLOF **********************************************************************
QEMU Starting
Build Date = Jul 17 2020 11:15:24
FW Version = git-e18ddad8516ff2cf
Press "s" to enter Open Firmware.
Populating /vdevice methods
Populating /vdevice/vty@71000000
Populating /vdevice/nvram@71000001
Populating /pci@800000020000000
00 0000 (D) : 1b36 000d serial bus [ usb-xhci ]
No NVRAM common partition, re-initializing...
Scanning USB
XHCI: Initializing
USB Storage
SCSI: Looking for devices
101000000000000 DISK : "QEMU QEMU HARDDISK 2.5+"
Using default console: /vdevice/vty@71000000
Welcome to Open Firmware
Copyright (c) 2004, 2017 IBM Corporation All rights reserved.
This program and the accompanying materials are made available
under the terms of the BSD License available at
http://www.opensource.org/licenses/bsd-license.php
Trying to load: from: /pci@800000020000000/usb@0/storage@1/disk@101000000000000 ...
E3405: No such device
E3407: Load failed
Type 'boot' and press return to continue booting the system.
Type 'reset-all' and press return to reboot the system.
Ready!
0 >
The device tree handed over by QEMU to SLOF indeed contains:
qemu,boot-list =
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000 HALT";
but the device node is named usb-xhci@0, not usb@0.
This happens because the firmware names of PCI devices returned
by get_boot_devices_list() come from pcibus_get_fw_dev_path(),
while the sPAPR PHB code uses a different naming scheme for
device nodes. This inconsistency has always been there but it was
hidden for a long time because SLOF used to rename USB device
nodes, until this commit, merged in QEMU 4.2.0 :
commit 85164ad4ed
Author: Alexey Kardashevskiy <aik@ozlabs.ru>
Date: Wed Sep 11 16:24:32 2019 +1000
pseries: Update SLOF firmware image
This fixes USB host bus adapter name in the device tree to match QEMU's
one.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fortunately, sPAPR implements the firmware path provider interface.
This provides a way to override the default firmware paths.
Just factor out the sPAPR PHB naming logic from spapr_dt_pci_device()
to a helper, and use it in the sPAPR firmware path provider hook.
Fixes: 85164ad4ed ("pseries: Update SLOF firmware image")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210122170157.246374-1-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In the CPU hotunplug bug [1] the guest kernel throws a scary
message in dmesg:
pseries-hotplug-cpu: Failed to offline CPU <NULL>, rc: -16
The reason isn't related to the bug though. This happens because the
kernel file arch/powerpc/platform/pseries/hotplug-cpu.c, function
dlpar_cpu_remove(), is not finding the device_node.name of the offending
CPU.
We're not populating the 'name' property for hotplugged CPUs. Since the
kernel relies on device_node.name for identifying CPU nodes, and the
CPUs that are coldplugged has the 'name' property filled by SLOF, this
is creating an unneeded inconsistency between hotplug and coldplug CPUs
in the kernel.
Let's fill the 'name' property for hotplugged CPUs as well. This will
make the guest dmesg throws a less intimidating message when we try to
unplug the last online CPU:
pseries-hotplug-cpu: Failed to offline CPU PowerPC,POWER9@1, rc: -16
[1] https://bugzilla.redhat.com/1911414
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210120232305.241521-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Next patch will use the 'nodename' string in spapr_core_dt_populate()
after the point it's being freed today.
Instead of moving 'g_free(nodename)' around, let's do a QoL change in
both CPU DT functions where 'nodename' is being freed, and use
g_autofree to avoid the 'g_free()' call altogether.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210120232305.241521-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add configuration options to enable or disable multiprocess QEMU code
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 6cc37253e35418ebd7b675a31a3df6e3c7a12dc1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allow RAM MemoryRegion to be created from an offset in a file, instead
of allocating at offset of 0 by default. This is needed to synchronize
RAM between QEMU & remote process.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 609996697ad8617e3b01df38accc5c208c24d74e.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
