The GICv3 specification says that reserved register addresses
should RAZ/WI. This means we need to return MEMTX_OK, not MEMTX_ERROR,
because now that we support generating external aborts the
latter will cause an abort on new board models.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
From the very beginning, post_load() was called from common
reset. This is not standard and obliged to discriminate the
reset case from the restore case using the iidr value.
Let's get rid of that call.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We change the restoration priority of both the GICv3 and ITS. The
GICv3 must be restored before the ITS and the ITS needs to be restored
before PCIe devices since it translates their MSI transactions.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 1497023553-18411-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We need to handle both registers and ITS tables. While
register handling is standard, ITS table handling is more
challenging since the kernel API is devised so that the
tables are flushed into guest RAM and not in vmstate buffers.
Flushing the ITS tables on device pre_save() is too late
since the guest RAM is already saved at this point.
Table flushing needs to happen when we are sure the vcpus
are stopped and before the last dirty page saving. The
right point is RUN_STATE_FINISH_MIGRATE but sometimes the
VM gets stopped before migration launch so let's simply
flush the tables each time the VM gets stopped.
For regular ITS registers we just can use vmstate pre_save()
and post_load() callbacks.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-3-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the basic skeleton for both KVM and software-emulated ITS.
Since we already prepare status structure, we also introduce complete
VMState description. But, because we currently have no migratable
implementations, we also set unmigratable flag.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
