da51e79b7f added two new ROM files
and removed an old one for eepro100.c.
These changes were missing in Makefile (which resulted
in a broken "make install").
Reported by Lucas Meneghel Rodrigues, thanks.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
As we hard-wire the BSP to CPU 0 anyway and cpuid_apic_id equals
cpu_index, bsp_to_cpu can also be based on the latter directly. This
will help an early user of it: KVM while initializing mp_state.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Do not write nmi_pending, sipi_vector, and mpstate unless we at least go
through a reset. And TSC as well as KVM wallclocks should only be
written on full sync, otherwise we risk to drop some time on state
read-modify-write.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This grand cleanup drops all reset and vmsave/load related
synchronization points in favor of four(!) generic hooks:
- cpu_synchronize_all_states in qemu_savevm_state_complete
(initial sync from kernel before vmsave)
- cpu_synchronize_all_post_init in qemu_loadvm_state
(writeback after vmload)
- cpu_synchronize_all_post_init in main after machine init
- cpu_synchronize_all_post_reset in qemu_system_reset
(writeback after system reset)
These writeback points + the existing one of VCPU exec after
cpu_synchronize_state map on three levels of writeback:
- KVM_PUT_RUNTIME_STATE (during runtime, other VCPUs continue to run)
- KVM_PUT_RESET_STATE (on synchronous system reset, all VCPUs stopped)
- KVM_PUT_FULL_STATE (on init or vmload, all VCPUs stopped as well)
This level is passed to the arch-specific VCPU state writing function
that will decide which concrete substates need to be written. That way,
no writer of load, save or reset functions that interact with in-kernel
KVM states will ever have to worry about synchronization again. That
also means that a lot of reasons for races, segfaults and deadlocks are
eliminated.
cpu_synchronize_state remains untouched, just as Anthony suggested. We
continue to need it before reading or writing of VCPU states that are
also tracked by in-kernel KVM subsystems.
Consequently, this patch removes many cpu_synchronize_state calls that
are now redundant, just like remaining explicit register syncs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
So far we synchronized any dirty VCPU state back into the kernel before
updating the guest debug state. This was a tribute to a deficite in x86
kernels before 2.6.33. But as this is an arch-dependent issue, it is
better handle in the x86 part of KVM and remove the writeback point for
generic code. This also avoids overwriting the flushed state later on if
user space decides to change some more registers before resuming the
guest.
We furthermore need to reinject guest exceptions via the appropriate
mechanism. That is KVM_SET_GUEST_DEBUG for older kernels and
KVM_SET_VCPU_EVENTS for recent ones. Using both mechanisms at the same
time will cause state corruptions.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Port qemu-kvm's -mem-path and -mem-prealloc options. These are useful
for backing guest memory with huge pages via hugetlbfs.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
CC: john cooper <john.cooper@redhat.com>
Instead of allocating a separate chunk for the first 640KB and another
for 1MB+, allocate one large chunk. This plays well in terms of alignment
and size with large pages.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
I always try to keep standard includes sorted
and add a comment why they are there (so they
can be removed when they are no longer needed).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
C++ comments are unwanted, so this is fixed here.
* Replace C++ comments by C comments.
* Put code which was deactivated by a C++ comment in #if 0...#endif.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Real hardware would run an internal self-test.
The emulation just returns a passed status.
Original patch was from Reimar Döffinger, thanks.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move code which reads the command block to the
new function read_cb. The patch also fixes some
endianess issues related to the command block
and moves declarations of local variables to
the beginning of the block.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no need for a local variable "status".
Using tx.status makes it clearer which status
is addressed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CU Start is allowed when the CU is in the idle or suspended state.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The RNR interrupt is triggered under these conditions:
* the RU is not ready to receive a frame due to missing resources
* the RU is ready and a RU abort command was requested
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When compiling with -Wshadow, gcc gives a warning
which is fixed by renaming stat -> status.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of magic numbers like 0x8000, symbolic names are used
for the SCB command and status bits.
There are too many configuration bits to use symbolic names
there, too. Using the BIT macro is a little help when comparing
code and documentation.
For the same reason, some other constants were replaced by
the BITS macro.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add descriptions for all devices.
These descriptions are shown when users call
qemu -device ?
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only two boot ROM files are needed for all devices.
* Add these GPXE ROM files using new naming convention
(as discussed on qemu-devel). Both files were created
with http://rom-o-matic.net/, PCI vendor / device ids
as in ROM filenames and option BANNER_TIMEOUT = 0.
* Remove old PXE ROM file for i82559er.
It was replaced by gpxe-eepro100-80861209.rom.
* Update pc-bios/README (and sort entries).
Full support still needs additional eepro100 fixes.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The phy handling was wrong for PXE, GPXE boot:
GPXE's eepro100 driver did not detect a valid link.
This is fixed here.
V2 - Use UPPER_CASE for enum values
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some system control block registers were addressed
using their offset value. Use symbolic names now
and clean the documentation.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When debug output was enabled (by defining DEBUG_EEPRO100),
some debug messages resulted in a compiler error.
This is fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Hello,
curses_keys.h is using obscure constant values while the curses.h header
provides fine defines, let's use the latter.
To be applied on top of my previous patch.
Samuel
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Hello,
There is a small incoherency in curses_keys.h, which makes it fail to
emit \n when using e.g. -k fr: curses2keysym transforms \r and 0x157
into \n, but name2keysym binds \r with Return, not \n. The patch below
fixes that.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
When restoring register values, increase the stack register for skipped
values.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Userspace doesn't have physical memory, so cpu_physical_memory_rw
makes no sense. This is only used to implement cpu_memory_rw_debug, so
just implement that directly instead.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Userspace emulation doesn't have a physical address space, so
l1_phys_map makes no sense. This code is never actually used, so don't
try and build it.
Signed-off-by: Paul Brook <paul@codesourcery.com>
implementation only widened the 32bit source vector elements into a
64bit destination vector but forgot to perform the actual shifting
operation.
Signed-off-by: Juha Riihimäki <juha.riihimaki@nokia.com>
Signed-off-by: Riku Voipio <riku.voipio@nokia.com>
Acked-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The rounding/truncating options were inverted. truncating
was done when rounding was meant and vice verse.
Signed-off-by: Riku Voipio <riku.voipio@nokia.com>
Acked-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If you make use of hw breakpoints on a 32bit x86 linux host, qemu
will segmentation fault when processing the exception.
The problem is that the value of env is stored in $ebp in the op_helper
raise_exception() function, and it can have the wrong value when
calling it from non generated code.
It is possible to work around the problem by restoring the value of
env before calling raise_exception() using a new helper function that
takes (CPUState *) as one of the arguments.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move userland PALcode handling into linux-user main loop so that
we can send signals from there. This also makes alpha_palcode.c
system-level only, so don't build it for userland. Add defines
for GENTRAP PALcall mapping to signals.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
