Enough to please U-Boot and make it able to detect SDRAM SPD EEPROMs
Signed-off-by: François Revol <revol@free.fr>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PIIX4 errata says that "immediate polling of the Host Status Register BUSY
bit may indicate that the SMBus is NOT busy."
Due to this, some code does the following steps:
(a) set parameters
(b) start command
(c) check for smbus busy bit set (to know that command started)
(d) check for smbus busy bit not set (to know that command finished)
Let (c) happen, by immediately setting the busy bit, and really executing
the command when status register has been read once.
This fixes a problem with AMIBIOS, which can now properly initialize the PIIX4.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Don't use old_mmio in the memory region ops struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505580378-9044-6-git-send-email-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=tEkM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20170601' into staging
migration/next for 20170601
# gpg: Signature made Thu 01 Jun 2017 17:51:04 BST
# gpg: using RSA key 0xF487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/migration/20170601:
migration: Move include/migration/block.h into migration/
migration: Export ram.c functions in its own file
migration: Create include for migration snapshots
migration: Export rdma.c functions in its own file
migration: Export tls.c functions in its own file
migration: Export socket.c functions in its own file
migration: Export fd.c functions in its own file
migration: Export exec.c functions in its own file
migration: Split qemu-file.h
migration: Remove unneeded includes of migration/vmstate.h
migration: shut src return path unconditionally
migration: fix leak of src file on dst
migration: Remove section_id parameter from vmstate_load
migration: loadvm handlers are not used
migration: Use savevm_handlers instead of loadvm copy
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller maintains a state machine in the command
register, which is mostly used for debug.
Let's start adding a few states to handle abnormal STOP
commands. Today, the model uses the busy status of the bus as a
condition to do so but it is not precise enough.
Also remove the ABNORMAL bit for failing TX commands. This is
incorrect with respect to the specs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1494827476-1487-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Today, the LAST command is handled with the STOP command but this is
incorrect. Also nack the I2C bus when a LAST is issued.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1494827476-1487-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Multiple I2C commands can be fired simultaneously and the controller
execute the commands following these priorities:
(1) Master Start Command
(2) Master Transmit Command
(3) Slave Transmit Command or Master Receive Command
(4) Master Stop Command
The current code is incorrect with respect to the above sequence and
needs to be reworked to handle each individual command.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1494827476-1487-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split the file into public and internal interfaces. I have to rename
the external one because we can't have two include files with the same
name in the same directory. Build system gets confused. The only
exported functions are the ones that handle basic types.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The imx25 chip provides 3 i2c buses, but they have all been named
"i2c", which makes it difficult to predict which bus a device will
be connected to when specified on the command line.
This patch addresses the issue by naming the buses uniquely:
i2c-bus.0 i2c-bus.1 i2c-bus.2
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20170105043430.3176-2-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a NULL check for i2c slave init callbacks, so that we no longer
need to implement empty init functions.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20161202054617.6749-4-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: squashed in later tweak from Alistair to if() phrasing]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the guest attempts to talk to a nonexistent device over i2c,
the i2c_start_transfer() function will return non-zero, indicating
that the bus is signalling a NACK. Similarly, if the i2c_send()
function returns nonzero then the target device returned a NACK.
Handle this possibility in the bitbang_i2c code, by returning
the state machine to the STOPPED state and returning the NACK
bit to the guest.
This bit of missing functionality was spotted by Coverity
(it noticed that we weren't checking the return value from
i2c_start_transfer()).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1477332749-27098-1-git-send-email-peter.maydell@linaro.org
Some SMBus operations restart the transfer to convert from
write to read mode without an intervening i2c_end_transfer().
The second call cannot fail, so the return code is unchecked,
but this causes Coverity to complain. So add some asserts
and documentation about this.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change 2293c27fad (i2c: implement broadcast write) added broadcast
capability to the I2C bus, but it broke SMBus read transactions.
An SMBus read transaction does two i2c_start_transaction() calls
without an intervening i2c_end_transfer() call. This will
result in i2c_start_transfer() adding the same device to the
current_devs list twice, and then the ->event() for the same
device gets called twice in the second call to i2c_start_transfer(),
resulting in the smbus code getting confused.
Note that this happens even with pure I2C devices when simulating
SMBus over I2C.
This fix only scans the bus if the current set of devices is empty.
This means that the current set of devices stays fixed until
i2c_end_transfer() is called, which is really what you want.
This also deletes the empty check from the top of i2c_end_transfer().
It's unnecessary, and it prevents the broadcast variable from being
set to false at the end of the transaction if no devices were on
the bus.
Cc: KONRAD Frederic <fred.konrad@greensocs.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Kwon <hyun.kwon@xilinx.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1470153614-6657-1-git-send-email-minyard@acm.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU fails migration with following error:
qemu-system-x86_64: Missing section footer for i2c_bus
qemu-system-x86_64: load of migration failed: Invalid argument
when migrating from:
qemu-system-x86_64-v2.6.0 -m 256M rhel72.img -M pc-i440fx-2.6
to
qemu-system-x86_64-v2.7.0-rc0 -m 256M rhel72.img -M pc-i440fx-2.6
Regression is added by commit 2293c27f (i2c: implement broadcast write)
Fix it by dropping 'broadcast' VMState introduced by 2293c27f and
reuse broadcast 0x00 address as broadcast flag in bus->saved_address.
Then if there were ongoing broadcast at migration time, set
bus->saved_address to it and at i2c_slave_post_load() time check
for it instead of transfering and using 'broadcast' VMState.
As result of reusing existing saved_address VMState, no compat
glue will be needed to keep forward/backward compatiblity. which
makes fix much less intrusive.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1469623198-177227-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ICH9 SMB bridge can be created using qdev API despite existence of helper
function. The type name is needed for such creation. Using a preprocessor
alias instead the string type name itself is preferable.
The patch makes the alias accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement an I2C slave which implements DDC and returns the
EDID data for an attached monitor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1465833014-21982-7-git-send-email-fred.konrad@greensocs.com
- Rebased on the current master.
- Modified for QOM.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
[PMM: actually wire up the vmstate to dc->vmsd]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most of the control flow logic between send and recv (error checking
etc) is the same. Factor this out into a common send_recv() API.
This is then usable by clients, where the control logic for send
and receive differs only by a boolean. E.g.
if (send)
i2c_send(...):
else
i2c_recv(...);
becomes:
i2c_send_recv(... , send);
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1465833014-21982-4-git-send-email-fred.konrad@greensocs.com
Changes from FK:
* Rebased on master.
* Rebased on my i2c broadcast patch.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This does a write to every slaves when the I2C bus get a write to address 0.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-3-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The dev field in i2cbus is not used.
So just drop it.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-2-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-5-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the omap_i2c_init into an instance_init and realize function
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-4-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Rename the exynos4210_i2c_realize to exynos4210_i2c_init
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-3-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
directly connected to the APB bus. They can be programmed as master or
slave but the propopsed model only supports the master mode.
On the TODO list, we also have :
- improve and harden the state machine.
- bus recovery support (used by the Linux driver).
- transfer mode state machine bits. this is not strictly necessary as
it is mostly used for debug. The bus busy bit is deducted from the
I2C core engine of qemu.
- support of the pool buffer: 2048 bytes of internal SRAM (not used
by the Linux driver).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1464704307-25178-1-git-send-email-clg@kaod.org
[PMM: removed unused functions aspeed_i2c_bus_get_state() and
aspeed_i2c_bus_set_state()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-36-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Device init() methods aren't supposed to call hw_error(), they should
report the error and fail cleanly. Do that.
The errors are all device misconfiguration. All callers use
qdev_init_nofail(), so this patch merely converts hw_error() crashes
into &error_abort crashes. Improvement, because now it crashes closer
to where the misconfiguration bug would be, and a few more bad
examples of hw_error() use are gone.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1450370121-5768-3-git-send-email-armbru@redhat.com>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() output is following the same format as
the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 328acfe6fc09a5afdbfbfd5220e0869fd5082660.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The slave mode is not implemented.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 508dbf2ebe26ec383d3a12a1db5a7890ac8acf20.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As core.c, piix4.c, ich9.c and pcihp.c are for x86, add CONFIG_ACPI_X86
to make it only for x86. ARM doesn't support cpu and memory hotplug, add
CONFIG_ACPI_CPU_HOTPLUG and CONFIG_ACPI_MEMORY_HOTPLUG to exclude them
for target-arm.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1432522520-8068-24-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are a number of ffs(3) callers that do roughly:
bit = ffs(val);
if (bit) {
do_something(bit - 1);
}
This pattern can be converted to ctz32() like this:
zeroes = ctz32(val);
if (zeroes != 32) {
do_something(zeroes);
}
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-6-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Steps:
1.enable qemu debug print, using simply scprit as below:
grep "//#define DEBUG" * -rl | xargs sed -i "s/\/\/#define DEBUG/#define DEBUG/g"
2. make -j
3. get some warning:
hw/i2c/pm_smbus.c: In function 'smb_ioport_writeb':
hw/i2c/pm_smbus.c:142: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/i2c/pm_smbus.c:142: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i2c/pm_smbus.c: In function 'smb_ioport_readb':
hw/i2c/pm_smbus.c:209: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/intc/i8259.c: In function 'pic_ioport_read':
hw/intc/i8259.c:373: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/input/pckbd.c: In function 'kbd_write_command':
hw/input/pckbd.c:232: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/input/pckbd.c: In function 'kbd_write_data':
hw/input/pckbd.c:333: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_writeb':
hw/isa/apm.c:44: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/isa/apm.c:44: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_readb':
hw/isa/apm.c:67: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/timer/mc146818rtc.c: In function 'cmos_ioport_write':
hw/timer/mc146818rtc.c:394: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i386/pc.c: In function 'port92_write':
hw/i386/pc.c:479: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
Fix them.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Pointer properties can be set only by code, not by device_add. A
device with a pointer property can work with device_add only when the
property may remain null.
This is the case for property "interrupt_vector" of device
"etraxfs,pic". Add a comment there.
Set cannot_instantiate_with_device_add_yet for the other devices with
pointer properties, with a comment explaining why.
Juha Riihimäki and Peter Maydell deserve my thanks for making "pointer
property must not remain null" blatantly obvious in the OMAP devices.
Only device "smbus-eeprom" is actually changed. The others are all
sysbus devices, which get cannot_instantiate_with_device_add_yet set
in their abstract base's class init function. Setting it again in
their class init function is technically redundant, but serves as
insurance for when sysbus devices become available with device_add,
and as documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> (for ETRAX)
Signed-off-by: Andreas Färber <afaerber@suse.de>
An ICH9 southbridge contains several PCI devices, some of them with
multiple functions. We model each function as a separate qdev. Two
of them need some special wiring set up in pc_q35_init() to work: the
LPC controller at 00:1f.0, and the SMBus controller at 00:1f.3.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The name field in a VMStateDescription is part of the migration state
versioning, so changing it will break migration. It's therefore a
bad idea to use a QOM typename macro to initialize it, because in
general we're free to rename QOM types as part of code refactoring
and cleanup. For the handful of devices that were doing this by
mistake, replace the QOM typenames with the corresponding literal
strings.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
[AF: Use TYPE_PVSCSI for TypeInfo instead]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Previous realization doesn't consider flags in the status register.
Add DS and INTR bits of HST_STS register set after transaction execution.
Update bits resetting in HST_STS register. Update error processing:
if DEV_ERR bit set transaction isn't execution.
Signed-off-by: MRatnikov <m.o.ratnikov@gmail.com>
Message-id: 1373230982-9190-1-git-send-email-m.o.ratnikov@gmail.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
