mirror of
https://github.com/proski/madwifi
synced 2024-11-29 17:53:12 +03:00
4e9cfeafe3
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@2863 0192ed92-7a03-0410-a25b-9323aeb14dbd
239 lines
9.6 KiB
C
239 lines
9.6 KiB
C
/*-
|
|
* Copyright (c) 2002-2006 Sam Leffler, Errno Consulting, Atheros
|
|
* Communications, Inc. All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms are permitted
|
|
* provided that the following conditions are met:
|
|
* 1. The materials contained herein are unmodified and are used
|
|
* unmodified.
|
|
* 2. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following NO
|
|
* ''WARRANTY'' disclaimer below (''Disclaimer''), without
|
|
* modification.
|
|
* 3. Redistributions in binary form must reproduce at minimum a
|
|
* disclaimer similar to the Disclaimer below and any redistribution
|
|
* must be conditioned upon including a substantially similar
|
|
* Disclaimer requirement for further binary redistribution.
|
|
* 4. Neither the names of the above-listed copyright holders nor the
|
|
* names of any contributors may be used to endorse or promote
|
|
* product derived from this software without specific prior written
|
|
* permission.
|
|
*
|
|
* NO WARRANTY
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT,
|
|
* MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
* IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE
|
|
* FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
|
|
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
|
|
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
|
|
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
|
|
* OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGES.
|
|
*
|
|
* $Id$
|
|
*/
|
|
|
|
#ifndef _DEV_ATH_DESC_H
|
|
#define _DEV_ATH_DESC_H
|
|
|
|
#include "opt_ah.h" /* NB: required for AH_SUPPORT_AR5416 */
|
|
|
|
/*
|
|
* Transmit descriptor status. This structure is filled
|
|
* in only after the tx descriptor process method finds a
|
|
* ``done'' descriptor; at which point it returns something
|
|
* other than HAL_EINPROGRESS.
|
|
*
|
|
* Note that ts_antenna may not be valid for all h/w. It
|
|
* should be used only if non-zero.
|
|
*/
|
|
struct ath_tx_status {
|
|
u_int16_t ts_seqnum; /* h/w assigned sequence number */
|
|
u_int16_t ts_tstamp; /* h/w assigned timestamp */
|
|
u_int8_t ts_status; /* frame status, 0 => xmit ok */
|
|
u_int8_t ts_rate; /* h/w transmit rate index */
|
|
#define HAL_TXSTAT_ALTRATE 0x80 /* alternate xmit rate used */
|
|
int8_t ts_rssi; /* tx ack RSSI */
|
|
u_int8_t ts_shortretry; /* # short retries */
|
|
u_int8_t ts_longretry; /* # long retries */
|
|
u_int8_t ts_virtcol; /* virtual collision count */
|
|
u_int8_t ts_antenna; /* antenna information */
|
|
u_int8_t ts_finaltsi; /* final transmit series index */
|
|
#ifdef AH_SUPPORT_AR5416
|
|
/* 802.11n status */
|
|
u_int8_t ts_flags; /* misc flags */
|
|
int8_t ts_rssi_ctl[3]; /* tx ack RSSI [ctl, chain 0-2] */
|
|
int8_t ts_rssi_ext[3]; /* tx ack RSSI [ext, chain 0-2] */
|
|
/* #define ts_rssi ts_rssi_combined */
|
|
u_int32_t ts_ba_low; /* blockack bitmap low */
|
|
u_int32_t ts_ba_high; /* blockack bitmap high */
|
|
u_int32_t ts_evm0; /* evm bytes */
|
|
u_int32_t ts_evm1;
|
|
u_int32_t ts_evm2;
|
|
#endif /* AH_SUPPORT_AR5416 */
|
|
};
|
|
|
|
/* bits found in ts_status */
|
|
#define HAL_TXERR_XRETRY 0x01 /* excessive retries */
|
|
#define HAL_TXERR_FILT 0x02 /* blocked by tx filtering */
|
|
#define HAL_TXERR_FIFO 0x04 /* fifo underrun */
|
|
#define HAL_TXERR_XTXOP 0x08 /* txop exceeded */
|
|
#define HAL_TXERR_DESC_CFG_ERR 0x10 /* Error in 20/40 desc config */
|
|
#define HAL_TXERR_DATA_UNDERRUN 0x20 /* Tx buffer underrun */
|
|
#define HAL_TXERR_DELIM_UNDERRUN 0x40 /* Tx delimiter underrun */
|
|
|
|
/* bits found in ts_flags */
|
|
#define HAL_TX_BA 0x01 /* Block Ack seen */
|
|
#define HAL_TX_AGGR 0x02 /* Aggregate */
|
|
|
|
/*
|
|
* Receive descriptor status. This structure is filled
|
|
* in only after the rx descriptor process method finds a
|
|
* ``done'' descriptor; at which point it returns something
|
|
* other than HAL_EINPROGRESS.
|
|
*
|
|
* If rx_status is zero, then the frame was received ok;
|
|
* otherwise the error information is indicated and rs_phyerr
|
|
* contains a phy error code if HAL_RXERR_PHY is set. In general
|
|
* the frame contents is undefined when an error occurred thought
|
|
* for some errors (e.g. a decryption error), it may be meaningful.
|
|
*
|
|
* Note that the receive timestamp is expanded using the TSF to
|
|
* at least 15 bits (regardless of what the h/w provides directly).
|
|
* Newer hardware supports a full 32-bits; use HAL_CAP_32TSTAMP to
|
|
* find out if the hardware is capable.
|
|
*
|
|
* rx_rssi is in units of dbm above the noise floor. This value
|
|
* is measured during the preamble and PLCP; i.e. with the initial
|
|
* 4us of detection. The noise floor is typically a consistent
|
|
* -96dBm absolute power in a 20MHz channel.
|
|
*/
|
|
struct ath_rx_status {
|
|
u_int16_t rs_datalen; /* rx frame length */
|
|
u_int8_t rs_status; /* rx status, 0 => recv ok */
|
|
u_int8_t rs_phyerr; /* phy error code */
|
|
int8_t rs_rssi; /* rx frame RSSI (combined for 11n) */
|
|
u_int8_t rs_keyix; /* key cache index */
|
|
u_int8_t rs_rate; /* h/w receive rate index */
|
|
u_int8_t rs_more; /* more descriptors follow */
|
|
u_int32_t rs_tstamp; /* h/w assigned timestamp */
|
|
u_int32_t rs_antenna; /* antenna information */
|
|
#ifdef AH_SUPPORT_AR5416
|
|
/* 802.11n status */
|
|
int8_t rs_rssi_ctl[3]; /* rx frame RSSI [ctl, chain 0-2] */
|
|
int8_t rs_rssi_ext[3]; /* rx frame RSSI [ext, chain 0-2] */
|
|
u_int8_t rs_isaggr; /* is part of the aggregate */
|
|
u_int8_t rs_moreaggr; /* more frames in aggr to follow */
|
|
u_int8_t rs_num_delims; /* number of delims in aggr */
|
|
u_int8_t rs_flags; /* misc flags */
|
|
u_int32_t rs_evm0; /* evm bytes */
|
|
u_int32_t rs_evm1;
|
|
u_int32_t rs_evm2;
|
|
#endif /* AH_SUPPORT_AR5416 */
|
|
};
|
|
|
|
/* bits found in rs_status */
|
|
#define HAL_RXERR_CRC 0x01 /* CRC error on frame */
|
|
#define HAL_RXERR_PHY 0x02 /* PHY error, rs_phyerr is valid */
|
|
#define HAL_RXERR_FIFO 0x04 /* fifo overrun */
|
|
#define HAL_RXERR_DECRYPT 0x08 /* non-Michael decrypt error */
|
|
#define HAL_RXERR_MIC 0x10 /* Michael MIC decrypt error */
|
|
|
|
/* bits found in rs_flags */
|
|
#define HAL_RX_MORE 0x01 /* more descriptors follow */
|
|
#define HAL_RX_MORE_AGGR 0x02 /* more frames in aggr */
|
|
#define HAL_RX_GI 0x04 /* full gi */
|
|
#define HAL_RX_2040 0x08 /* 40 MHz */
|
|
#define HAL_RX_DELIM_CRC_PRE 0x10 /* crc error in delimiter pre */
|
|
#define HAL_RX_DELIM_CRC_POST 0x20 /* crc error in delim after */
|
|
#define HAL_RX_DECRYPT_BUSY 0x40 /* decrypt was too slow */
|
|
#define HAL_RX_DUP_FRAME 0x80 /* Dup frame rx'd on control channel */
|
|
|
|
enum {
|
|
HAL_PHYERR_UNDERRUN = 0, /* Transmit underrun */
|
|
HAL_PHYERR_TIMING = 1, /* Timing error */
|
|
HAL_PHYERR_PARITY = 2, /* Illegal parity */
|
|
HAL_PHYERR_RATE = 3, /* Illegal rate */
|
|
HAL_PHYERR_LENGTH = 4, /* Illegal length */
|
|
HAL_PHYERR_RADAR = 5, /* Radar detect */
|
|
HAL_PHYERR_SERVICE = 6, /* Illegal service */
|
|
HAL_PHYERR_TOR = 7, /* Transmit override receive */
|
|
/* NB: these are specific to the 5212 */
|
|
HAL_PHYERR_OFDM_TIMING = 17, /* */
|
|
HAL_PHYERR_OFDM_SIGNAL_PARITY = 18, /* */
|
|
HAL_PHYERR_OFDM_RATE_ILLEGAL = 19, /* */
|
|
HAL_PHYERR_OFDM_LENGTH_ILLEGAL = 20, /* */
|
|
HAL_PHYERR_OFDM_POWER_DROP = 21, /* */
|
|
HAL_PHYERR_OFDM_SERVICE = 22, /* */
|
|
HAL_PHYERR_OFDM_RESTART = 23, /* */
|
|
HAL_PHYERR_CCK_TIMING = 25, /* */
|
|
HAL_PHYERR_CCK_HEADER_CRC = 26, /* */
|
|
HAL_PHYERR_CCK_RATE_ILLEGAL = 27, /* */
|
|
HAL_PHYERR_CCK_SERVICE = 30, /* */
|
|
HAL_PHYERR_CCK_RESTART = 31, /* */
|
|
};
|
|
|
|
/* value found in rs_keyix to mark invalid entries */
|
|
#define HAL_RXKEYIX_INVALID ((u_int8_t) -1)
|
|
/* value used to specify no encryption key for xmit */
|
|
#define HAL_TXKEYIX_INVALID ((u_int) -1)
|
|
|
|
/* XXX rs_antenna definitions */
|
|
|
|
/*
|
|
* Definitions for the software frame/packet descriptors used by
|
|
* the Atheros HAL. This definition obscures hardware-specific
|
|
* details from the driver. Drivers are expected to fillin the
|
|
* portions of a descriptor that are not opaque then use HAL calls
|
|
* to complete the work. Status for completed frames is returned
|
|
* in a device-independent format.
|
|
*/
|
|
#ifdef AH_SUPPORT_AR5416
|
|
#define HAL_DESC_HW_SIZE 20
|
|
#else
|
|
#define HAL_DESC_HW_SIZE 4
|
|
#endif /* AH_SUPPORT_AR5416 */
|
|
|
|
struct ath_desc {
|
|
/*
|
|
* The following definitions are passed directly
|
|
* the hardware and managed by the HAL. Drivers
|
|
* should not touch those elements marked opaque.
|
|
*/
|
|
u_int32_t ds_link; /* phys address of next descriptor */
|
|
u_int32_t ds_data; /* phys address of data buffer */
|
|
u_int32_t ds_ctl0; /* opaque DMA control 0 */
|
|
u_int32_t ds_ctl1; /* opaque DMA control 1 */
|
|
u_int32_t ds_hw[HAL_DESC_HW_SIZE]; /* opaque h/w region */
|
|
};
|
|
|
|
struct ath_desc_status {
|
|
union {
|
|
struct ath_tx_status tx;/* xmit status */
|
|
struct ath_rx_status rx;/* recv status */
|
|
} ds_us;
|
|
};
|
|
|
|
#define ds_txstat ds_us.tx
|
|
#define ds_rxstat ds_us.rx
|
|
|
|
/* flags passed to tx descriptor setup methods */
|
|
#define HAL_TXDESC_CLRDMASK 0x0001 /* clear destination filter mask */
|
|
#define HAL_TXDESC_NOACK 0x0002 /* don't wait for ACK */
|
|
#define HAL_TXDESC_RTSENA 0x0004 /* enable RTS */
|
|
#define HAL_TXDESC_CTSENA 0x0008 /* enable CTS */
|
|
#define HAL_TXDESC_INTREQ 0x0010 /* enable per-descriptor interrupt */
|
|
#define HAL_TXDESC_VEOL 0x0020 /* mark virtual EOL */
|
|
/* NB: this only affects frame, not any RTS/CTS */
|
|
#define HAL_TXDESC_DURENA 0x0040 /* enable h/w write of duration field */
|
|
#define HAL_TXDESC_EXT_ONLY 0x0080 /* send on ext channel only (11n) */
|
|
#define HAL_TXDESC_EXT_AND_CTL 0x0100 /* send on ext + ctl channels (11n) */
|
|
#define HAL_TXDESC_VMF 0x0200 /* virtual more frag */
|
|
|
|
/* flags passed to rx descriptor setup methods */
|
|
#define HAL_RXDESC_INTREQ 0x0020 /* enable per-descriptor interrupt */
|
|
#endif /* _DEV_ATH_DESC_H */
|