Use CONFIG_LOCALVERSION as an alternative to check that the
configuration settings have been included.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@4134 0192ed92-7a03-0410-a25b-9323aeb14dbd
However, the netif_rx and vlan_hwaccel_receive_skb functions dispatch the SKB to the higher networking levels, out of our domain.
Therefore, handle node references as appropriate.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3708 0192ed92-7a03-0410-a25b-9323aeb14dbd
* Convert last SKB_CB()->ni to SKB_NI
* Lots of comments
* Refactor various pieces of code for consistency, readability, and removal of goto
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3666 0192ed92-7a03-0410-a25b-9323aeb14dbd
* Lots of coding style and formatting, tedious and annoying
* Quite a few bad merges as far as I can tell; at least one of which was serious - reintroduced a leak
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3202 0192ed92-7a03-0410-a25b-9323aeb14dbd
We were setting this field to 0 as we had no easy way of determining
what TX power was used to transmit a frame. However, by including this
field and setting it to 0dBm we are saying that each frame is being
transmitted at 1mW, which is incorrect. Better to simply not write the
field at all, however this introduces the need for padding in the TX
header to ensure that the TX_FLAGS field is aligned to a 16-bit
boundary.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3014 0192ed92-7a03-0410-a25b-9323aeb14dbd
* Counters for total outstanding instances for each resource type (skb, ath_node and ath_buf)
* One pair of acquisition/release functions per resource type in unlocked and one in locked
* Adds some more _debug versions of functions in the call chain that acquire/release resources so that the original func/line in the driver as well as the func/line that affected the resource use can be shown in the trace. Intermediate stack frames aren't necessary to trace the leaks.
* Changes naming convention for "lock-required" functions to suffix _locked for the versions that expect locking, to be consistent with some other places in the code.
* Consolidate debug messages to the helper functions that actually affect the reference count or acquire/release a resource
* Additional sanity checks and leak detection (esp for detecting node ref leaks through skb)
* skb references are nulled out by the new sbk unref/free function.
I've tested these changes extensively and found lots of cases where we didn't get enough node references when cloning skbuff, and where the kernel drops packets due to performance issues and leaks our node references.
With these changes and the tracing enabled I have verified that:
* TX BUF: tx buffers always go down to zero when the tx queue is done, and you can watch tx queue usage ratio go up and down again as the driver is working. There are no leaks here at the moment, although there *are* some in the madwifi-dfs branch during CAC at the moment.
* skbuff leaks in all the common flows are fixed. We were leaking node references in a lot of places where kernel was dropping skb's due to congestion and we were failing to increment node references when cloning skbuffs. These are now detected, as are skbuffs that are reaped by the kernel while still holding a node reference.
* the ath_node count works correctly and on an idle system we get about 5 references per station table node, with 2 node instances per VAP. One for the bss and one for the node in the station table, I believe. The ath_node count goes up and down but always lands back at the stable number based on the vaps you have configured and the number of actual stations in the station table. The point here is that it's pretty constant what you will see over time, despite excessive node creation/release in our code during input (esp input_all). Thank god for the slab allocator.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@2902 0192ed92-7a03-0410-a25b-9323aeb14dbd
