1) Move all debug preprocessor flags out into make files
2) Add support for remaining preprocessor flags to be set by ENV variables
3) Add support for HAL tracing to include device name
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3481 0192ed92-7a03-0410-a25b-9323aeb14dbd
The need to use software instead of hardware for beacon timers in AP+STA mode (aka nosbeacon) is now just determined in software, as we always knew whether or not to enable this.
The confusing bssid and -bssid parameters are now deprecated.
The "uniquebssid" flag is equivalent to "bssid" and can be used to force IEEE80211_CLONE_BSSID flag. If this is not specified, then the BSSID used will be the next unused BSSID in the sequence, which could very well be the parent device's MAC address.
"uniquebssid" equates directly to IEEE80211_CLONE_BSSID" flag therefore.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3476 0192ed92-7a03-0410-a25b-9323aeb14dbd
* Restructure one set of control blocks into a more readable form
* Add some additional debug output
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3456 0192ed92-7a03-0410-a25b-9323aeb14dbd
This changeset adds a node statistic. If this is not liked, I encourage it to be fixed; I might learn something.
Thanks nbd.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3334 0192ed92-7a03-0410-a25b-9323aeb14dbd
So, ccmp_attach is called for each new key. Hence, only try to allocate a software context if IEEE80211_KEY_SWCRYPT is specified. Also, if we need a software context and fail, fail immediately; thus, the check in ccmp_setkey can be eleminated, as it is not actually a separate condition.
I think that when I touched this last, I was confused about the purpose of ccmp_attach.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3322 0192ed92-7a03-0410-a25b-9323aeb14dbd
time in ms, or the number of beacons for the
beacon miss alarm. If we haven't had a beacon
in this period, the alarm is sounded and
action (i.e. roaming) is taken.
This patch changes the storage of the beacon
miss threshold to integral beacon count but
corrects the previous intent.
The default beacon miss alarm is going to be
850ms which is half way between the two hard
coded limits that were there before.
The old hard coded limits assumed that the
beacon interval was 100ms and set the limit to
10 (1000ms) for software beacon miss timer
and 7 for hardware beacon miss timer.
The new default is 850ms (the midpoint between
the two previous defaults). This value is rounded
up to the next nearest beacon interval.
There is no upper bound on the beacon miss
threshold specified, since it may need to be
wildly inflated with 25ms beacon interval, or
wildly reduced with 1000ms beacon interval.
The minimum is still 2 beacons, regardless of
the beacon interval.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3314 0192ed92-7a03-0410-a25b-9323aeb14dbd
* Based on patches from nbd
* av_beacon_alloc code has been reimplemented using atomic bit operations; I think this is safe for SMP
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3310 0192ed92-7a03-0410-a25b-9323aeb14dbd
messages from 1000 to 192 and drop the length
needed to display the [atomic] node count.
Slamming this much data on the stack can cause
stack overflows with 4k stacks quite easily,
especially when hard interrupts occur and
extend a stack that is already almost full.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3307 0192ed92-7a03-0410-a25b-9323aeb14dbd
count of the new bss node. The allocation
function gives us a reference. With this extra
reference, every invocation of reset_bss was
causing a leak of one node ~4kb every time the
interface was brought back up (or the BSS was reset
for other reasons).
This fixes ticket #1682. I can run ifconfig down/up
cycle for a long time. I'll run it overnight next
to be sure.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3301 0192ed92-7a03-0410-a25b-9323aeb14dbd
node in the node table. The node reference was
being taken in any path where the wds node was found
and not just when the wds node was first added.
This would have caused wds nodes to get inflated
reference counts, and be leaked on bss reset when
nodes were flushed from the node tables.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3300 0192ed92-7a03-0410-a25b-9323aeb14dbd
copy of the bss node is used to send a message
we need to make sure all code paths release
it when done. This bug combined with repeated
auth failures would cause node references to
grow with every failure. Then, if you were
taking down the interface and bringing it back
up you would leak one page (4kb) every time the
the node table was flushed on transition to UP.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3299 0192ed92-7a03-0410-a25b-9323aeb14dbd
This changes some iwpriv names, because I believe they will be more readily usable and understandable
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3279 0192ed92-7a03-0410-a25b-9323aeb14dbd
