* Lots of coding style and formatting, tedious and annoying
* Quite a few bad merges as far as I can tell; at least one of which was serious - reintroduced a leak
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3202 0192ed92-7a03-0410-a25b-9323aeb14dbd
branch to trunk. especially notable is, that due to improved nexttbtt (next
"target beacon transmit time") calculation we will now get the correct backoff
behaviour for beacons, resulting in only one beacon per beacon interval (the
current head version will send N beacons for N stations in the beacon interval
because they are poorly synchronized). also because of the better timer
synchronization there is no more time lag of up to 1 minute until we see
beacons after a merge. thanks to benoit for figuring that out!
the difference between this patch and the version in the dfs-branch is that it
still uses self linked descriptors and uses the SWBA interrupt only for
updating the nexttbtt. this is necessary to recognize HW merges, for which we
don't get any notification by the hardware (see the thread "IBSS testing" on
this list for more details).
also i tried to clean up a bit, use a more descriptive function name for timer
updates (ath_beacon_update_timers instead of ath_beacon_config) and generally
better distingush between a HW merge and a SW merge.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@3027 0192ed92-7a03-0410-a25b-9323aeb14dbd
Preprocessor flag now used to toggle printk output prior to blocking on
a spinlock.
There is of course a chance that the spinlock will be taken between the time we check it and print our little message, but this should still be of some assistance troubleshoot locking mistakes that come up in the future.
If you turn on the flag, you can find out what locks are being contended for and from which functions... i.e. ath_intr fights for a particular lock, etc.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@2944 0192ed92-7a03-0410-a25b-9323aeb14dbd
* Counters for total outstanding instances for each resource type (skb, ath_node and ath_buf)
* One pair of acquisition/release functions per resource type in unlocked and one in locked
* Adds some more _debug versions of functions in the call chain that acquire/release resources so that the original func/line in the driver as well as the func/line that affected the resource use can be shown in the trace. Intermediate stack frames aren't necessary to trace the leaks.
* Changes naming convention for "lock-required" functions to suffix _locked for the versions that expect locking, to be consistent with some other places in the code.
* Consolidate debug messages to the helper functions that actually affect the reference count or acquire/release a resource
* Additional sanity checks and leak detection (esp for detecting node ref leaks through skb)
* skb references are nulled out by the new sbk unref/free function.
I've tested these changes extensively and found lots of cases where we didn't get enough node references when cloning skbuff, and where the kernel drops packets due to performance issues and leaks our node references.
With these changes and the tracing enabled I have verified that:
* TX BUF: tx buffers always go down to zero when the tx queue is done, and you can watch tx queue usage ratio go up and down again as the driver is working. There are no leaks here at the moment, although there *are* some in the madwifi-dfs branch during CAC at the moment.
* skbuff leaks in all the common flows are fixed. We were leaking node references in a lot of places where kernel was dropping skb's due to congestion and we were failing to increment node references when cloning skbuffs. These are now detected, as are skbuffs that are reaped by the kernel while still holding a node reference.
* the ath_node count works correctly and on an idle system we get about 5 references per station table node, with 2 node instances per VAP. One for the bss and one for the node in the station table, I believe. The ath_node count goes up and down but always lands back at the stable number based on the vaps you have configured and the number of actual stations in the station table. The point here is that it's pretty constant what you will see over time, despite excessive node creation/release in our code during input (esp input_all). Thank god for the slab allocator.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@2902 0192ed92-7a03-0410-a25b-9323aeb14dbd
catch messages that occur during VAP startup (before you can possibly invoke
80211debug).
Support for shared debug flags where they take effect across all devices
(i.e. shared flags in athdebug), and when they take effect across all VAPs
(i.e. shared flags in 80211debug).
Some additional debugging flags, including some in preparation for more leak
detection code to be merged shortly as well as some from madwifi-dfs.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@2888 0192ed92-7a03-0410-a25b-9323aeb14dbd
SET_MODULE_OWNER() is not defined in 2.6.24, but it's already a no-op in
2.6.23. Make sure that it will be a no-op in 2.6.23 and newer kernels.
git-svn-id: http://madwifi-project.org/svn/madwifi/trunk@2754 0192ed92-7a03-0410-a25b-9323aeb14dbd
benoit