if init() is called a second time. This allows me to restart a
simulation (wxwindows interface only) without restarting the whole
application.
- modified: iodev/*.cc
These seem to be working better, are a more simple design,
easier to understand, and AFAIK don't have race conditions
in them like the old ones do.
Re-coded the apic timer, to return cycle accurate values
which vary with each iteration of a read from a guest OS.
The previous implementation had very poor resolution. It
also didn't check the mask bit to see if an apic timer
interrupt should occur on countdown to 0. The apic timer
now calls its own bochs timer, rather than tag on the
one in iodev/devices.cc.
I needed to use one new function which is an inline in
pc_sytem.h. That would have to be added to the old pc_system.h if
we have to back-out to it.
Linux/x86-64 now boots until it hits two undefined opcodes:
FXRSTOR (0f ae). This restores FPU, MMX, XMM and MXCSR registers
from a 512-byte region of memory. We don't implement this yet.
MOVNTDQ (66 0f e7). This is a move involving an XMM register.
The 0x66 prefix is used so it's a double quadword, rather than
MOVNTQ (0f e7) which operates on a single quadword.
The Linux kernel panic is on the MOVNTQD opcodes. Perhaps that's
because that opcode is used in exception handling of the 1st?
Looks like we need to implement some new instructions.
requesting source can be registered as well. Otherwise, there
is no way to know which source modules are requesting
suspect frequencies which are too high.
to request bulk IO operations to IO devices which are bulk IO aware.
Currently, I modified only harddrv.cc to be aware. I added some
fields to the bx_devices_c class for the IO instructions to
place requests and receive responses from the IO device emulation.
Devices except the hard drive, don't monitor these fields so they
respond as normal. The hard drive now monitors these fields for
bulk requests, and if enabled, it memcpy()'s data straight from
the disk buffer to memory. This eliminates numerous inp/outp calling
sequences per disk sector.
I used the fields in bx_devices_c so that I would not have to
disrupt most IO device modules. Enhancements can be made to
other devices if they use high-bandwidth IO via in/out instructions.
Some devices already had one. Some I had to add an empty one.
I did a little cleaning of init() methods to make them more uniform
but generally I left them alone.
- I also put these exact diffs into a patch "patch.iodev-add-reset"
in case I want to revert these changes for some reason, for example
if they break an old patch. It should be deleted after a while.
DMA functions defined. Most of the changes are based on the "bochs sync"
version of plex86. Here is the list of changes:
* register/unregister functions for DMA channels added. The DMA controller
can use the DMA read/write handlers of registered devices directly.
* "hardwired" code in dma.cc removed
* all DMA related code in devices.cc and iodev.h removed
* DMA related code in pc_system.* removed except HRQ handling
* macros for DMA functions defined in bochs.h
* floppy and SB16 code modified to use the changes described above
. ports 0x0400 0x0401 and 0xfff0 : rombios
. ports 0x0500 0x0501 and 0x0502 : vgabios
The rombios log output was previously handled by the unmmapped device
- new functions raise_irq() and lower_irq()
- all trigger_irq() / untrigger_irq() calls are replaced by the new functions
- REMARK: timer IRQ handling is not correct but it works
- TODO: IOAPIC IRQ handling needs to be changed
Fixed a "feature" in pc_system.cc with setting timers to small values
that can cause bochs to hang.
Significantly improved the performance of the new PIT.
It's probably ready to become the default now.
Added a preliminary implementation of the slowdown timer
that Bryce and I had talked about.
BX_SUPPORT_APIC were used. To follow the pattern used by other
names like this, I changed them all to BX_SUPPORT_APIC.
Thanks to Tom Lindström for chasing this down!
To see the commit logs for this use either cvsweb or
cvs update -r BRANCH-io-cleanup and then 'cvs log' the various files.
In general this provides a generic interface for logging.
logfunctions:: is a class that is inherited by some classes, and also
. allocated as a standalone global called 'genlog'. All logging uses
. one of the ::info(), ::error(), ::ldebug(), ::panic() methods of this
. class through 'BX_INFO(), BX_ERROR(), BX_DEBUG(), BX_PANIC()' macros
. respectively.
.
. An example usage:
. BX_INFO(("Hello, World!\n"));
iofunctions:: is a class that is allocated once by default, and assigned
as the iofunction of each logfunctions instance. It is this class that
maintains the file descriptor and other output related code, at this
point using vfprintf(). At some future point, someone may choose to
write a gui 'console' for bochs to which messages would be redirected
simply by assigning a different iofunction class to the various logfunctions
objects.
More cleanup is coming, but this works for now. If you want to see alot
of debugging output, in main.cc, change onoff[LOGLEV_DEBUG]=0 to =1.
Comments, bugs, flames, to me: todd@fries.net
