- rewrite of the logical sector handling code to make seek latency support possible
- implemented variable HD seek latency for seek and read commands
- TODO #1: CD-ROM seek command returns status immediately, but it clears the DSC bit
and sets it at completion. Device should not accept ATAPI commands until DSC is set.
- TODO #2: clean up the seek latency code
- temporarily disabled seek latency support for ATAPI command 0x2b until the
seeking status is implemented correctly
- fix for the MSVC compilation fix (result was always 0.0)
- now using the more accurate name "seek latency"
- fixed CD-ROM LBA address range checks and renamed limit to "max_lba"
- make the latency for CD-ROM access variable depending on the distance between
current and new block address, Maximum value should only occur at first access
or after media change.
- TODO: make hard disk seek timing variable, too.
- still TODO: seek latency for USB drives (requires asynchronus packet support).
- If the runtime flag of a bx_list_c object is set, all it's items are set up
as runtime options.
- Set the runtime parameter for all top-level runtime-only lists. Setting up
each single parameter is no longer needed.
- use #if BX_SUPPORT_CDROM instead of #ifdef LOWLEVEL_CDROM
- devices with cdrom support now use the base class cdrom_base_c
- cdrom count variable moved to cdrom.cc
- cdrom_misc.cc: don't use ioctl's for ISO files
- removed parameter "present" and use the new drive type "none" instead
- re-implemented cdrom media status parameter as a bx_param_enum_c
- TODO: change floppy media status parameter type to be consistent
- renamed config parameter "i440fx_support" to "enabled"
- new config parameter "chipset" added (current choices "i430FX" and "i440FX")
- don't load ACPI support if the i430FX chipset is selected
- select register values for the core PCI devices depending on the chipset
- USB UHCI must be connected to a PCI slot if the i430FX chipset is used
- rombios changes to make the i430FX chipset work
- TODO #1: implement limitation to 1 cpu and 128 MB RAM for the i430FX chipset
- TODO #2: verify register behaviour of both chipsets
dummy parameter and it's save/restore handlers. Currently only the save
support is implemented and the specific save function is only written for
flat mode images (copies whole disk image file to the save/restore folder).
- TODO #1: implement save function for the other disk image modes
- TODO #2: add restore support (replace disk image file with the one from the
save/restore folder)
- bx_list_c: don't accept duplicate param names in list (except dependent lists
and special menus)
- added BX_PANIC for malloc() failure
- harddrv: fixed wrong variable found with bx_list_c changes
invalid module names, save log actions to bochsrc)
- added new member 'name' to the logfunctions class for the case the prefix
is too short. Added to some devices with longer names.
existing "iolight timer" code in the hard drive code. If an LED is registered
with the "auto-off" flag, the device only needs to turn on the LED to indicate
data transfer. The LED timer in the gui code turns it off after 0.5 seconds if
it is not actived by another transfer. Added this feature to all network
devices.
- TODO #1: implement this feature in the USB host controllers
- TODO #2: the unused timer in the hard drive code could be used for the
emulation of seek functions
* if the image provides a geometry, always use it.
* if the cylinder value is set to 0 and the image supports autodetection,
calculate the cylinder value from disk size, sectors and heads.
* in all other cases the specified geometry is used.
* a panic only occurs if the image size is too small for the geometry.
* extra data past the end of the disk now causes an info message.
- TODO #1: 'flat' mode hdimage: read disk size of raw devices on Linux
- TODO #2: 'flat' mode hdimage: use geometry from MBR on image if present
parameters (path + status) have been set. TODO: implement this feature for the floppy, too.
- call update_drive_status_buttons() from update_runtime_options() to reduce the number of calls.
Now call update_runtime_options() from the gui floppy / cdrom handlers after closing dialog.
duplicate log prefixes on Windows if both IDE and USB cdroms are used in plugin mode. Windows also
requires the cdrom base class and the init_cdrom() method to link and work correctly.
* moved runtime handlers for cdrom from config.cc to the device object
* cd media status variable is now always of type bx_bool
* changed obsolete gui names like "cdromD" to "cdrom1"
* TODO: implement new runtime config mechanism similar to USB
