Reduce duplication of code by
* Removing from elf_common.h definitions available in os/kernel/elf.h
* Deleting elf32.h and elf64.h
* Renaming elf_common.h to elf_private.h
* Updating source to build using public and private ELF header files
together
Signed-off-by: Jessica Hamilton <jessica.l.hamilton@gmail.com>
* Called via arm_mailbox_bcm2835 *and* arm_framebuffer_bcm2835
* This is a bit messy. We really should be getting these
chipset-centric bases from the provided FDT / DTB.
* I can't think of a way to redo this without undoing
work towards FDT.
* The Raspberry pi 2 uses a new SoC which differs slightly
from the Raspberry Pi 1.
* Someday these two board targets could go away when we get
FDT support.
* To while there was some compatibility between
BCM2708 and BCM2805, it makes the BCM2806 changes
more confusing. We don't have any valueable BCM2708
targets.
The BOOT_GDT_SEGMENT_COUNT was based on USER_DATA_SEGMENT on both
x86 and x86_64. However, on x86_64 the order of the segments is
different, leading to a too small gBootGDT array. Move the define to
the arch specific headers so they can be setup correctly in either case.
Also add a STATIC_ASSERT() to check that the descriptors fit into the
array.
Pointed out by CID 1210898.
This patch adds user_access() which can be used to gracefully handle
page faults that may happen when accessing user memory. It is used
by arch_cpu_user{memcpy, memset, strlcpy}() to allow using optimized
functions from the standard library.
Currently only x64 uses this, but nothing really is arch specific here.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
The kernel is allowed to use fpu anywhere so we must make sure that
user state is not clobbered by saving fpu state at interrupt entry.
There is no need to do that in case of system calls since all fpu
data registers are caller saved.
We do not need, though, to save the whole fpu state at task swich
(again, thanks to calling convention). Only status and control
registers are preserved. This patch actually adds xmm0-15 register
to clobber list of task swich code, but the only reason of that is
to make sure that nothing bad happens inside the function that
executes that task swich. Inspection of the generated code shows
that no xmm registers are actually saved.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
Enable SSE as a part of the "preparation of the environment to run any
C or C++ code" in the entry points of stage2 bootloader.
SSE2 is going to be used by memset() and memcpy().
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
The possibility to specify custom memcpy and memset implementations
in cpu modules is currently unused and there is generally no point
in such feature.
There are only 2 x86 vendors that really matter and there isn't
very big difference in performance of the generic optmized versions
of these funcions across different models. Even if we wanted different
versions of memset and memcpy depending on the processor model or
features much better solution would be to use STT_GNU_IFUNC and save
one indirect call.
Long story short, we don't really benefit in any way from
get_optimized_functions and the feature it implements and it only adds
unnecessary complexity to the code.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
* Removes default mapping of a portion of the RAM (will be done
as needed)
* Passes on the page directory area to kernel, so on early vm init
the kernel can use the area for pagetable allocation.
* Leaves it to the platform to pass in physical memory range(s). This
will ultimately come from FDT.
* Fix long standing issue with allocation of the heap, potentially
causing other part of the bootloader to overwrite the heap.
* Implements pagetable allocator in kernel for early vm mapping.
This fixes the first PANIC seen, we now just get the same one later
on when the VM is up... more to come...
This reverts commit 3fbb24680c.
As I mentioned in #11131, this fix is not correct, and works around
the problem. The real reason was that arch_debug_call_with_fault_handler
was not working properly, so the fault handler went crazy.
With commit eb92810 that is fixed so this can be reverted.
If GCC knows what these functions are actually doing the resulting
code can be optimized better what is especially noticeable in case of
invocations of atomic_{or,and}() that ignore the result. Obviously,
everything is inlined what also improves performance.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
When an ARMv7 CPU is detected, immediately turn on the FPU. This allows
us to use vsnprintf in the TRACE call in that function, as our libc is
compiled with floating point support and will trigger a fault if the FPU
is not available.
This lets the boot go further, and crash in mmu_init. Next steps:
* Find why mmu_init is crashing
* Setup some fault handlers, otherwise we call uboot ones, and they are
not very helpful. They will also probably not work once the mmu is
enabledvery helpful. They will also probably not work once the mmu is
enabledvery helpful. They will also probably not work once the mmu is
enabled...
This patch makes it possible to inline rdmsr and wrmsr instruction. The
performance impact shouldn't be significant since they are used relatively
rarely and wrmsr is usually a serializing instruction, but there is no reason
not to do so.
The goal of this patch is to amortize the cost of context switch by making
the compiler aware that context switch clobbers all registers. Because all
register need to be saved anyway there is no additional cost of using
callee saved register in the function that does the context switch.
Similarly to previous patch regarding GDT this is mostly a rewrite of
IDT handling code from C to C++. Thanks to constexpr IDT is now entirely
generated at compile-time.
Virtually no functional change, just rewriting the code from
"C in *.cpp files" to C++. Use of constexpr may be advantageous but
that code is not performance critical anyway.
* Add isb just because.
* pdziepak pointed out that ARMv5 and before
had different barrier support.
* pdziepak also mentioned that dsb was too strong
for __sync_synchronize
* On ARMv6 or older, we do a simulated dsb.
* Move __sync_synchronize into thread.c in libroot
and use the new arch_atomic.h dsb/dmb defines.
* Gets arm @bootstrap-raw to end of bootstrap.
* Don't assume verdex as it isn't clear this was
occurring.
* Make an educated guess on HAIKU_BOOT_PLATFORM
based on provided board (but still allow it to
be overridden)
* Error out if user doesn't populate
HAIKU_BOOT_PLATFORM or enters an unknown board
name.
* You need to add "-sHAIKU_BOOT_BOARD=xxx" to
your jam to build for the proper ARM device.
* Rename beagle to beagleboneblk as per the
documentation.
* Use atomic_get_and_set for return value
* Atomics are no longer volatile
* Add missing arch_cpu_pause stub
* Move arch_cpu_idle to arch_cpu header to match
other architectures
* Set max cpu to 1 for PPC until atomic functions are finished
* We have atomic functions inline in the kernel and assembly
code in libroot post-scheduler merge... isn't that a lot of
duplication?
