Since we're using multi-part uImage format, we can add the FDT as
a seperate "blob" in the uImage, if the used U-Boot version is not
"FDT enabled".
This is used for example for our Verdex target. Currently I've got
a local hack in the platform/u-boot/Jamfile, looking into pulling
in the FDT files and a proper Jam setup to do that properly...
This detects everything up to ARMv6 right now. Need to check more
recent ARM ARMs for ARMv7 detection.
The detected details get passed on to the kernel, which can use
the pre-detected info for selecting right pagetable format and such.
Copyright removal of Axel done after agreement with Axel @ BeGeistert
that for files that were copy/pasted from x86 arch and then fully
replaced the implementation, removal of original copyright holder is
allowed, since their actual code is gone ;)
This is to make sure all ARM platforms will benefit from planned work on this
MMU/CPU code. The less code duplicated, the better.
Compile-tested for all supported ARM platforms
This also implements the fault handler correctly now, and cleans up the
exception handling. Seems a lot more stable now, no unexpected panics or
faults happening anymore.
* The only implementation that would accept more than 2 TB was the one in
scsi_disk. But even that one was limited to 63 TB.
* Now there is a new utility function devfs_compute_geometry_size() which
does it correctly for sizes up to 2^64 which should be good enough for
quite some time :-)
* This fixes bug #8992.
The lowest 4 bits of the MSR serves as a hint to the hardware to
favor performance or energy saving. 0 means a hint preference for
highest performance while 15 corresponds to the maximum energy
savings. A value of 7 translates into a hint to balance performance
with energy savings.
The default reset value of the MSR is 0. If BIOS doesn't intialize
the MSR, the hardware will run in performance state. This patch
initialize the MSR with value of 7 for balance between performance
and energy savings
Signed-off-by: Fredrik Holmqvist <fredrik.holmqvist@gmail.com>
Renamed {32,64}/int.cpp to {32,64}/descriptors.cpp, which now contain
functions for GDT and TSS setup that were previously in arch_cpu.cpp,
as well as the IDT setup code. These get called from the init functions
in arch_cpu.cpp, rather than having a bunch of ifdef'd chunks of code
for 32/64.
Reused x86 arch_user_debugger.cpp, with a few minor changes to make
the code work for both 32 and 64 bit. Something isn't quite working
right, if a breakpoint is hit the kernel will hang. Other than that
everything appears to work correctly.
* Changed IS_USER_ADDRESS to check an address using USER_BASE and
USER_SIZE, rather than just !IS_KERNEL_ADDRESS. The old check would
allow user buffers to point into the physical memory map area.
* Added an unmapped hole at the end of the bottom half of the address
space which catches buffers that cross into the uncanonical address
region. This also removes the need to check for uncanonical return
addresses in the syscall handler, it is no longer possible for the
return address to be uncanonical under normal circumstances. All
cases in which the return address might be changed by the kernel
are still handled via the IRET path.
The cookie is used to store the base address of the area that was just
visited. On 64-bit systems, int32 is not sufficient. Therefore, changed
to ssize_t which retains compatibility on x86 while expanding to a
sufficient size on x86_64.
Userland switch is implemented, as is basic system call support (using
SYSCALL/SYSRET). The system call handler is not yet complete: it doesn't
handle more than 6 arguments, and does not perform all the necessary kernel
entry/exit work (neither does the interrupt handler). However, this is
sufficient for runtime_loader to start and print some debug output.
Since this argument may be used to pass pointers, uint32 is not
correct for 64-bit. Effectively no change on 32-bit targets, both
size_t and uint32 are unsigned long there.
No major changes to the kernel: just compiled in arch_smp.cpp and fixed the
IDT load in arch_cpu_init_percpu to use the correct limit for x86_64 (uses
sizeof(interrupt_descriptor)). In the boot loader, changed smp_boot_other_cpus
to construct a temporary GDT and get the page directory address from CR3, as
what's in kernel_args will be 64-bit stuff and will not work to switch the
CPUs into 32-bit mode in the trampoline code. Refactored 64-bit kernel entry
code to not use the stack after disabling paging, as the secondary CPUs are
given a 32-bit virtual stack address by the SMP trampoline code which will
no longer work.
A proper page fault handler was required for areas that were not locked
into the kernel address space. This enables the boot process to get
up to the point of trying to find the boot volume.
* Thread creation and switching is working fine, however threads do not yet
get interrupted because I've not implemented hardware interrupt handling
yet (I'll do that next).
* I've made some changes to struct iframe: I've removed the e/r prefixes
from the member names for both 32/64, so now they're just named ip, ax,
bp, etc. This makes it easier to write code that works with both 32/64
without having to deal with different iframe member names.
This has been done by adding typedefs in elf_common.h to the correct ELF
structures for the architecture, and changing all Elf32_* uses to those
types. I don't know whether image loading works as I cannot test it yet,
there may be some 64-bit safety issues around. However, symbol lookup for
the kernel is working correctly.
* Uses 64-bit multiplication, special handling for CPUs clocked < 1 GHz
in system_time_nsecs() not required like on x86.
* Tested against a straight conversion of the x86 version, noticably
faster with a large number of system_time() calls.
* Added empty source files for all the 64-bit paging method code, and a
stub implementation of X86PagingMethod64Bit.
* arch_vm_translation_map.cpp has been modified to use X86PagingMethod64Bit
on x86_64.
* Some things are currently ifndef'd out completely for x86_64 because
they aren't implemented, there's a few other ifdef's to handle x86_64
differences but most of the code works unchanged.
* Renamed some i386_* functions to x86_*.
* Added a temporary method for setting the current thread on x86_64
(a global variable, not SMP safe). This will be changed to be done
via the GS segment but I've not implemented that yet.
For now I've just put all the stub functions that are needed to link the
kernel into a file called stubs.cpp. I've not yet moved across the interrupt
handling code or the ELF64 relocation code to the x86 directory. Once those
have been moved I can get rid of the x86_64 headers/source directories.
Not many changes seeing as there's not much x86_64 stuff done yet. Small
differences are handled with ifdefs, large differences (descriptors.h,
struct iframe) have separate headers under arch/x86/32 and arch/x86/64.
