NetBSD/sys/dev/ic/mb86950reg.h

147 lines
5.7 KiB
C

/* $NetBSD: mb86950reg.h,v 1.2 2005/04/03 11:37:19 jdolecek Exp $ */
/*
* Copyright (c) 1995 Mika Kortelainen
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Mika Kortelainen
* 4. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Adapted from if_qnreg.h for the amiga port of NetBSD by Dave J. Barnes, 2004.
*/
/*
* The Fujitsu mb86950, "EtherStar", is the predecessor to the mb8696x
* NICE supported by the ate driver. While similar in function and
* programming to the mb8696x, the register offset differences and
* quirks make it nearly impossible to have one driver for both the
* EtherStar and NICE chips.
*
* Definitions from Fujitsu documentation.
*/
#define ESTAR_DLCR0 0 /* Transmit status */
#define DLCR_TX_STAT ESTAR_DLCR0
#define ESTAR_DLCR1 1 /* Transmit masks */
#define DLCR_TX_INT_EN ESTAR_DLCR1
/* DLCR0/1 - Transmit Status & Masks */
#define TX_DONE 0x80 /* Transmit okay */
/* bit 6 - Net Busy, carrier sense ? */
/* bit 5 - Transmit packet received ? */
#define TX_CR_LOST 0x10 /* Carrier lost while attempting to transmit */
#define TX_UNDERFLO 0x08 /* fifo underflow */
#define TX_COL 0x04 /* Collision */
#define TX_16COL 0x02 /* 16 collision */
#define TX_BUS_WR_ERR 0x01 /* Bus write error, fifo overflo */
#define CLEAR_TX_ERR (TX_UNDERFLO | TX_COL | TX_16COL | TX_BUS_WR_ERR) /* Clear transmit errors */
#define TX_MASK (TX_DONE | TX_16COL)
#define ESTAR_DLCR2 2 /* Receive status */
#define DLCR_RX_STAT ESTAR_DLCR2
#define ESTAR_DLCR3 3 /* Receive masks */
#define DLCR_RX_INT_EN ESTAR_DLCR3
/* DLCR2/3 - Receive Status & Masks */
#define RX_PKT 0x80 /* Packet ready */
#define RX_BUS_RD_ERR 0x40 /* fifo underflow, harmless, normally masked off */
/* bit 5 - DMA end of process ? */
/* bit 4 - remote control packet rx ? */
#define RX_SHORT_ERR 0x08 /* Short packet */
#define RX_ALIGN_ERR 0x04 /* Alignment error */
#define RX_CRC_ERR 0x02 /* CRC error */
#define RX_OVERFLO 0x01 /* Receive buf overflow */
#define CLEAR_RX_ERR RX_MASK /* Clear receive and errors */
#define RX_MASK (RX_PKT | RX_SHORT_ERR | RX_ALIGN_ERR | RX_CRC_ERR | RX_OVERFLO | RX_BUS_RD_ERR)
#define RX_ERR_MASK (RX_SHORT_ERR | RX_ALIGN_ERR | RX_CRC_ERR | RX_OVERFLO | RX_BUS_RD_ERR)
#define ESTAR_DLCR4 4 /* Transmit mode */
#define DLCR_TX_MODE ESTAR_DLCR4
/* DLCR4 - Transmit Mode */
/* bits 7, 6, 5, 4 - collision count ? */
#define COL_MASK 0xf0
/* bit 3 - nc */
/* bit 2 - gen output ? */
#define LBC 0x02 /* Loopback control */
/* bit 0 - defer ?, normally 0 */
#define ESTAR_DLCR5 5 /* Receive mode */
#define DLCR_RX_MODE ESTAR_DLCR5
/* DLCR5 - Receive Mode */
/* Normal mode: accept physical address, broadcast address.
*/
/* bit 7 - Disable CRC test mode */
#define RX_BUF_EMTY 0x40 /* Buffer empty */
/* bit 5 - accept packet with errors or nc ?, normally set to 0 */
/* bit 4 - 40 bit address ?, normally set to 0 */
/* bit 3 - accept runts ?, normally set to 0 */
/* bit 2 - remote reset ? normally set to 0 */
/* bit 1 & 0 - address filter mode */
/* 00 = reject */
/* 01 = normal mode */
#define NORMAL_MODE 0x01
/* 10 = ? */
/* 11 = promiscuous mode */
#define PROMISCUOUS_MODE 0x03 /* Accept all packets */
#define ESTAR_DLCR6 6 /* Software reset */
#define DLCR_CONFIG ESTAR_DLCR6
/* DLCR6 - Enable Data Link Controller */
#define DISABLE_DLC 0x80 /* Disable data link controller */
#define ENABLE_DLC 0x00 /* Enable data link controller */
#define ESTAR_DLCR7 7 /* TDR (LSB) */
#define ESTAR_DLCR8 8 /* Node ID0 */
#define DLCR_NODE_ID ESTAR_DLCR8
#define ESTAR_DLCR9 9 /* Node ID1 */
#define ESTAR_DLCR10 10 /* Node ID2 */
#define ESTAR_DLCR11 11 /* Node ID3 */
#define ESTAR_DLCR12 12 /* Node ID4 */
#define ESTAR_DLCR13 13 /* Node ID5 */
#define ESTAR_DLCR15 15 /* TDR (MSB) */
/* The next three are usually accessed as words */
#define ESTAR_BMPR0 16 /* Buffer memory port (FIFO) */
#define BMPR_FIFO ESTAR_BMPR0
#define ESTAR_BMPR2 18 /* Packet length */
#define BMPR_TX_LENGTH ESTAR_BMPR2
/* BMPR2:BMPR3 - Packet Length Registers (Write-only) */
#define TRANSMIT_START 0x8000
#define ESTAR_BMPR4 20 /* DMA enable */
#define BMPR_DMA ESTAR_BMPR4