166 lines
5.9 KiB
Plaintext
166 lines
5.9 KiB
Plaintext
/* $NetBSD: README,v 1.3 2007/10/17 19:56:54 garbled Exp $ */
|
|
|
|
Overview
|
|
|
|
This is a port to the Motorola "SandPoint" evaluation system. The
|
|
SandPoint is the successor to the "Yellowknife" system. The system
|
|
can be fitted with different PMCs (Processor Mezzanine Cards). This
|
|
port is specifically for the rev X2 motherboard system with the PPC
|
|
8240 PMC rev X4 installed. It also works with the Altimus X2 PMC
|
|
(MPC7400 with MPC107).
|
|
|
|
All references (cf) listed here are for the MPC8240 Integrated Processor
|
|
User's Manual.
|
|
|
|
Information on the Sandpoint can be found on Motorola's web site:
|
|
http://www.mot.com/SPS/PowerPC/teksupport/refdesigns/sandpoint.html
|
|
|
|
|
|
SandPoint Hardware Configuration
|
|
|
|
This port was developed on a Sandpoint X2 motherboard with a Unity X4 PMC.
|
|
|
|
This port assumes that the jumpers are set as follows:
|
|
S3/S4 - Mode 1: PMC w/o IDE (switches opposite, one nearest PCI
|
|
slot toward near edge)
|
|
S5 - Interrupt to PMC normal (switch toward near edge)
|
|
S6 - Local I/O shared with slot 2 (switch toward near edge)
|
|
|
|
Mode 0 (PMC w/ IDE) does not appear to work right with ISA interrupts. The
|
|
interrupts from the Winbond chip do not appear at the PMC.
|
|
|
|
On the PPMC, we assume a 100MHz clock.
|
|
on PPMC: (C == closed, or "on")
|
|
SW2:
|
|
C ROM on PCI bus (DINK32 on mainboard)
|
|
- Map "B": CHRP
|
|
C Motorola PPMC
|
|
C Wait for initialization (peripheral mode)
|
|
- Program mode: Normal mode
|
|
- Select normal ROM
|
|
- 33 MHz only
|
|
- COP only resets local CPU/MPC107
|
|
SW3:
|
|
-C--C PCI 33, Mem 66, PPC 266
|
|
-- 0.5 - 0.9 ns PCI hold time
|
|
C 25 ohm PCI drive strength
|
|
|
|
|
|
Address Map
|
|
|
|
For this port, we choose the "Address Map B" (CHRP-compatible) for the
|
|
system (see SW2, #2, above):
|
|
|
|
(Processor View)
|
|
0000 0000 0009 FFFF System Memory
|
|
000A 0000 000F FFFF Compatibility Hole (programmable to go to PCI space
|
|
or system memory--programmed for system memory--cf 5.8)
|
|
0010 0000 3FFF FFFF System memory
|
|
4000 0000 7FFF FFFF Reserved (programmed to give a memory select
|
|
error if accessed--cf 5.7.2)
|
|
8000 0000 FCFF FFFF PCI memory space
|
|
FD00 0000 FDFF FFFF PCI/ISA memory space (see 5.8, CPU_FD_ALIAS_EN)
|
|
FE00 0000 FE7F FFFF PCI/ISA I/O space (Forwarded to PCI address space
|
|
with high byte zeroed, but FE01 0000 and up are
|
|
reserved)
|
|
FE80 0000 FEBF FFFF PCI I/O space (Forwarded to PCI I/O space with high
|
|
byte zeroed)
|
|
FEC0 0000 FEDF FFFF PCI configuration address register (Each word in this
|
|
range is aliased to the PCI CONFIG_ADDR register)
|
|
FEE0 0000 FEEF FFFF PCI configuration data register (Each word in this
|
|
range is aliased to the PCI CONFIG_DATA register)
|
|
FEF0 0000 FEFF FFFF PCI interrupt acknowledge
|
|
FF00 0000 FF7F FFFF 32- or 64-bit Flash/ROM space (Can hit either local
|
|
memory or PCI bus -- cf. 5.6)
|
|
FF80 0000 FFFF FFFF 8-, 32- or 64-bit Flash/ROM space (Can hit either
|
|
local memory or PCI bus -- cf. 5.6)
|
|
|
|
This is a host-mode port, so the inbound and output translation windows
|
|
are unused.
|
|
|
|
The Embedded Utilities Memory Block (EUMB) is set to be 1M below the end
|
|
of the PCI memory space: FC00 0000, so EUMBBAR is FC00 0000, giving us
|
|
|
|
Message unit (I2O) base : FC00 0000 (cf. 10.2, 10.2.3, 10.3)
|
|
DMA base : FC00 1000 (cf. 9.2)
|
|
ATU base : FC00 2000 (cf. 4.3.3)
|
|
I2C base : FC00 3000 (cf. 11.3)
|
|
EPIC base : FC04 0000 (cf. 12.2)
|
|
|
|
|
|
|
|
Boot Information
|
|
|
|
The SandPoint ships with the Motorola DINK32 ROM. This is a rather
|
|
basic ROM with only serial-download (S-Record) capability for
|
|
loading the kernel. Basically, the kernel is loaded to a specified
|
|
address and you jump to it. The ROM takes care of initializing
|
|
the MICRs and MCCRs. There is really no boot information to pass.
|
|
|
|
It would be nice to have a much more complete ROM interface, allowing
|
|
settings for, say, bootp/tftp boot, automatic boot, and persistent
|
|
settings (for console rate, auto boot, bootp, etc), and that might
|
|
be provided at some point, but that's not available as of this
|
|
writing.
|
|
|
|
So, the kernel is hard-coded to boot w/ 32MB for now.
|
|
|
|
|
|
|
|
Interrupt Configuration
|
|
|
|
The 8240 has the internal EPIC. For the SandPoint, the EPIC is programmed
|
|
in mixed-mode (GCR) with direct interrupts (EICR). With this configuration,
|
|
there are 13 available interrupts:
|
|
4 global timers
|
|
5 direct IRQs
|
|
IRQ0 - PCI Slot #0 INTA#
|
|
IRQ1 - PCI Slot #1 INTA# / shared with WinBond I/O
|
|
IRQ2 - PCI Slot #2 INTA#
|
|
IRQ3 - PCI Slot #3 INTA#
|
|
IRQ4 - On-PPMC 16552 interrupt (Unity X2)
|
|
IRQ4 - pulled down w/ resistor (Unity X4)
|
|
4 internal interrupts
|
|
I2C
|
|
DMA Ch0
|
|
DMA Ch1
|
|
I2O message unit
|
|
|
|
The SandPoint can run in one of 4 interrupt modes:
|
|
0 - PMC host with IDE (3.3v PCI slots are unavailable)
|
|
1 - PMC host w/o IDE (all PCI slots are available)
|
|
2 - PMC agent, Winbond providing arbitration & interrupt to INTA# on PMC
|
|
3 - Yellowknife mode--just like #2, except drives INTA# on 4th PCI slot
|
|
|
|
We choose to run in mode 1 as Motorola recommends modes 0 or 1 for
|
|
all new development. Unfortunately, mode 0 does not appear to
|
|
work--"ISA" interrupts are lost. In this mode, with interrupts
|
|
routed to PCI slot 3, we have to check for both a Winbond (ISA)
|
|
interrupt, and a PCI slot interrupt. So basically, we have a
|
|
two-level interrupt configuration for Winbond interrupts. The ISA
|
|
bus attachment registers an interrupt for PCI slot 3 with its own
|
|
interrupt handler. Drivers for ISA devices on the Winbond will
|
|
register interrupts with the ISA interrupt handler. The sticky
|
|
part of this is how to deal with one global interrupt priority.
|
|
|
|
|
|
|
|
SandPoint III "SP3" Interrupt Configuration
|
|
|
|
With a help of additional logic circuit SP3 organizes external
|
|
interrupt sources as EPIC serial mode interrupts.
|
|
16 serial IRQs
|
|
IRQ0 - WinBond South bridge i8259 PIC, polarity inverted
|
|
IRQ1 - reserved
|
|
IRQ2 - PCI Slot #1, INTA#
|
|
IRQ3 - PCI Slot #2, INTA#
|
|
IRQ4 - PCI Slot #3, INTA#
|
|
IRQ5 - PCI Slot #4, INTA#
|
|
IRQ6 - WinBond INTA#
|
|
IRQ7 - WinBond INTB#
|
|
IRQ8 - WinBond INTC#
|
|
IRQ9 - WinBond INTD#
|
|
IRQ10 thru 15 - reserved
|
|
SP3 provides switch selections to emulate SP1/2 compatible EPIC
|
|
direct mode interrupt assignments.
|