569 lines
15 KiB
C
569 lines
15 KiB
C
/* $NetBSD: si_vme.c,v 1.17 2002/09/27 20:36:32 thorpej Exp $ */
|
|
|
|
/*-
|
|
* Copyright (c) 1996 The NetBSD Foundation, Inc.
|
|
* All rights reserved.
|
|
*
|
|
* This code is derived from software contributed to The NetBSD Foundation
|
|
* by Adam Glass, David Jones, and Gordon W. Ross.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. All advertising materials mentioning features or use of this software
|
|
* must display the following acknowledgement:
|
|
* This product includes software developed by the NetBSD
|
|
* Foundation, Inc. and its contributors.
|
|
* 4. Neither the name of The NetBSD Foundation nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
|
|
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
|
|
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
|
|
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
/*
|
|
* This file contains only the machine-dependent parts of the
|
|
* Sun3 SCSI driver. (Autoconfig stuff and DMA functions.)
|
|
* The machine-independent parts are in ncr5380sbc.c
|
|
*
|
|
* Supported hardware includes:
|
|
* Sun SCSI-3 on OBIO (Sun3/50,Sun3/60)
|
|
* Sun SCSI-3 on VME (Sun3/160,Sun3/260)
|
|
*
|
|
* Could be made to support the Sun3/E if someone wanted to.
|
|
*
|
|
* Note: Both supported variants of the Sun SCSI-3 adapter have
|
|
* some really unusual "features" for this driver to deal with,
|
|
* generally related to the DMA engine. The OBIO variant will
|
|
* ignore any attempt to write the FIFO count register while the
|
|
* SCSI bus is in DATA_IN or DATA_OUT phase. This is dealt with
|
|
* by setting the FIFO count early in COMMAND or MSG_IN phase.
|
|
*
|
|
* The VME variant has a bit to enable or disable the DMA engine,
|
|
* but that bit also gates the interrupt line from the NCR5380!
|
|
* Therefore, in order to get any interrupt from the 5380, (i.e.
|
|
* for reselect) one must clear the DMA engine transfer count and
|
|
* then enable DMA. This has the further complication that you
|
|
* CAN NOT touch the NCR5380 while the DMA enable bit is set, so
|
|
* we have to turn DMA back off before we even look at the 5380.
|
|
*
|
|
* What wonderfully whacky hardware this is!
|
|
*
|
|
* Credits, history:
|
|
*
|
|
* David Jones wrote the initial version of this module, which
|
|
* included support for the VME adapter only. (no reselection).
|
|
*
|
|
* Gordon Ross added support for the OBIO adapter, and re-worked
|
|
* both the VME and OBIO code to support disconnect/reselect.
|
|
* (Required figuring out the hardware "features" noted above.)
|
|
*
|
|
* The autoconfiguration boilerplate came from Adam Glass.
|
|
*/
|
|
|
|
/*****************************************************************
|
|
* VME functions for DMA
|
|
****************************************************************/
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/errno.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/malloc.h>
|
|
#include <sys/device.h>
|
|
#include <sys/buf.h>
|
|
#include <sys/proc.h>
|
|
#include <sys/user.h>
|
|
|
|
#include <dev/scsipi/scsi_all.h>
|
|
#include <dev/scsipi/scsipi_all.h>
|
|
#include <dev/scsipi/scsipi_debug.h>
|
|
#include <dev/scsipi/scsiconf.h>
|
|
|
|
#include <machine/autoconf.h>
|
|
#include <machine/dvma.h>
|
|
|
|
/* #define DEBUG XXX */
|
|
|
|
#include <dev/ic/ncr5380reg.h>
|
|
#include <dev/ic/ncr5380var.h>
|
|
|
|
#include "sireg.h"
|
|
#include "sivar.h"
|
|
|
|
void si_vme_dma_setup __P((struct ncr5380_softc *));
|
|
void si_vme_dma_start __P((struct ncr5380_softc *));
|
|
void si_vme_dma_eop __P((struct ncr5380_softc *));
|
|
void si_vme_dma_stop __P((struct ncr5380_softc *));
|
|
|
|
void si_vme_intr_on __P((struct ncr5380_softc *));
|
|
void si_vme_intr_off __P((struct ncr5380_softc *));
|
|
|
|
static void si_vme_reset __P((struct ncr5380_softc *));
|
|
|
|
/*
|
|
* New-style autoconfig attachment
|
|
*/
|
|
|
|
static int si_vme_match __P((struct device *, struct cfdata *, void *));
|
|
static void si_vme_attach __P((struct device *, struct device *, void *));
|
|
|
|
const struct cfattach si_vme_ca = {
|
|
sizeof(struct si_softc), si_vme_match, si_vme_attach
|
|
};
|
|
|
|
/*
|
|
* Options for disconnect/reselect, DMA, and interrupts.
|
|
* By default, allow disconnect/reselect on targets 4-6.
|
|
* Those are normally tapes that really need it enabled.
|
|
*/
|
|
int si_vme_options = 0x0f;
|
|
|
|
|
|
static int
|
|
si_vme_match(parent, cf, aux)
|
|
struct device *parent;
|
|
struct cfdata *cf;
|
|
void *aux;
|
|
{
|
|
struct confargs *ca = aux;
|
|
int probe_addr;
|
|
|
|
/* No default VME address. */
|
|
if (ca->ca_paddr == -1)
|
|
return (0);
|
|
|
|
/* Make sure something is there... */
|
|
probe_addr = ca->ca_paddr + 1;
|
|
if (bus_peek(ca->ca_bustype, probe_addr, 1) == -1)
|
|
return (0);
|
|
|
|
/*
|
|
* If this is a VME SCSI board, we have to determine whether
|
|
* it is an "sc" (Sun2) or "si" (Sun3) SCSI board. This can
|
|
* be determined using the fact that the "sc" board occupies
|
|
* 4K bytes in VME space but the "si" board occupies 2K bytes.
|
|
*/
|
|
/* Note: the "si" board should NOT respond here. */
|
|
probe_addr = ca->ca_paddr + 0x801;
|
|
if (bus_peek(ca->ca_bustype, probe_addr, 1) != -1) {
|
|
/* Something responded at 2K+1. Maybe an "sc" board? */
|
|
#ifdef DEBUG
|
|
printf("si_vme_match: May be an `sc' board at pa=0x%x\n",
|
|
ca->ca_paddr);
|
|
#endif
|
|
return(0);
|
|
}
|
|
|
|
/* Default interrupt priority. */
|
|
if (ca->ca_intpri == -1)
|
|
ca->ca_intpri = 2;
|
|
|
|
return (1);
|
|
}
|
|
|
|
static void
|
|
si_vme_attach(parent, self, args)
|
|
struct device *parent, *self;
|
|
void *args;
|
|
{
|
|
struct si_softc *sc = (struct si_softc *) self;
|
|
struct ncr5380_softc *ncr_sc = &sc->ncr_sc;
|
|
struct cfdata *cf = self->dv_cfdata;
|
|
struct confargs *ca = args;
|
|
|
|
/* Get options from config flags if specified. */
|
|
if (cf->cf_flags)
|
|
sc->sc_options = cf->cf_flags;
|
|
else
|
|
sc->sc_options = si_vme_options;
|
|
|
|
printf(": options=0x%x\n", sc->sc_options);
|
|
|
|
sc->sc_adapter_type = ca->ca_bustype;
|
|
sc->sc_regs = (struct si_regs *)
|
|
bus_mapin(ca->ca_bustype, ca->ca_paddr,
|
|
sizeof(struct si_regs));
|
|
sc->sc_adapter_iv_am =
|
|
VME_SUPV_DATA_24 | (ca->ca_intvec & 0xFF);
|
|
|
|
/*
|
|
* MD function pointers used by the MI code.
|
|
*/
|
|
ncr_sc->sc_pio_out = ncr5380_pio_out;
|
|
ncr_sc->sc_pio_in = ncr5380_pio_in;
|
|
ncr_sc->sc_dma_alloc = si_dma_alloc;
|
|
ncr_sc->sc_dma_free = si_dma_free;
|
|
ncr_sc->sc_dma_setup = si_vme_dma_setup;
|
|
ncr_sc->sc_dma_start = si_vme_dma_start;
|
|
ncr_sc->sc_dma_poll = si_dma_poll;
|
|
ncr_sc->sc_dma_eop = si_vme_dma_eop;
|
|
ncr_sc->sc_dma_stop = si_vme_dma_stop;
|
|
ncr_sc->sc_intr_on = si_vme_intr_on;
|
|
ncr_sc->sc_intr_off = si_vme_intr_off;
|
|
|
|
/* Attach interrupt handler. */
|
|
isr_add_vectored(si_intr, (void *)sc,
|
|
ca->ca_intpri, ca->ca_intvec);
|
|
|
|
/* Reset the hardware. */
|
|
si_vme_reset(ncr_sc);
|
|
|
|
/* Do the common attach stuff. */
|
|
si_attach(sc);
|
|
}
|
|
|
|
static void
|
|
si_vme_reset(struct ncr5380_softc *ncr_sc)
|
|
{
|
|
struct si_softc *sc = (struct si_softc *)ncr_sc;
|
|
volatile struct si_regs *si = sc->sc_regs;
|
|
|
|
#ifdef DEBUG
|
|
if (si_debug) {
|
|
printf("si_vme_reset\n");
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* The SCSI3 controller has an 8K FIFO to buffer data between the
|
|
* 5380 and the DMA. Make sure it starts out empty.
|
|
*
|
|
* The reset bits in the CSR are active low.
|
|
*/
|
|
si->si_csr = 0;
|
|
delay(10);
|
|
si->si_csr = SI_CSR_FIFO_RES | SI_CSR_SCSI_RES | SI_CSR_INTR_EN;
|
|
delay(10);
|
|
si->fifo_count = 0;
|
|
|
|
/* Make sure the DMA engine is stopped. */
|
|
si->dma_addrh = 0;
|
|
si->dma_addrl = 0;
|
|
si->dma_counth = 0;
|
|
si->dma_countl = 0;
|
|
si->si_iv_am = sc->sc_adapter_iv_am;
|
|
si->fifo_cnt_hi = 0;
|
|
}
|
|
|
|
/*
|
|
* This is called when the bus is going idle,
|
|
* so we want to enable the SBC interrupts.
|
|
* That is controlled by the DMA enable!
|
|
* Who would have guessed!
|
|
* What a NASTY trick!
|
|
*/
|
|
void
|
|
si_vme_intr_on(ncr_sc)
|
|
struct ncr5380_softc *ncr_sc;
|
|
{
|
|
struct si_softc *sc = (struct si_softc *)ncr_sc;
|
|
volatile struct si_regs *si = sc->sc_regs;
|
|
|
|
/* receive mode should be safer */
|
|
si->si_csr &= ~SI_CSR_SEND;
|
|
|
|
/* Clear the count so nothing happens. */
|
|
si->dma_counth = 0;
|
|
si->dma_countl = 0;
|
|
|
|
/* Clear the start address too. (paranoid?) */
|
|
si->dma_addrh = 0;
|
|
si->dma_addrl = 0;
|
|
|
|
/* Finally, enable the DMA engine. */
|
|
si->si_csr |= SI_CSR_DMA_EN;
|
|
}
|
|
|
|
/*
|
|
* This is called when the bus is idle and we are
|
|
* about to start playing with the SBC chip.
|
|
*/
|
|
void
|
|
si_vme_intr_off(ncr_sc)
|
|
struct ncr5380_softc *ncr_sc;
|
|
{
|
|
struct si_softc *sc = (struct si_softc *)ncr_sc;
|
|
volatile struct si_regs *si = sc->sc_regs;
|
|
|
|
si->si_csr &= ~SI_CSR_DMA_EN;
|
|
}
|
|
|
|
/*
|
|
* This function is called during the COMMAND or MSG_IN phase
|
|
* that precedes a DATA_IN or DATA_OUT phase, in case we need
|
|
* to setup the DMA engine before the bus enters a DATA phase.
|
|
*
|
|
* XXX: The VME adapter appears to suppress SBC interrupts
|
|
* when the FIFO is not empty or the FIFO count is non-zero!
|
|
*
|
|
* On the VME version, setup the start addres, but clear the
|
|
* count (to make sure it stays idle) and set that later.
|
|
*/
|
|
void
|
|
si_vme_dma_setup(ncr_sc)
|
|
struct ncr5380_softc *ncr_sc;
|
|
{
|
|
struct si_softc *sc = (struct si_softc *)ncr_sc;
|
|
struct sci_req *sr = ncr_sc->sc_current;
|
|
struct si_dma_handle *dh = sr->sr_dma_hand;
|
|
volatile struct si_regs *si = sc->sc_regs;
|
|
long data_pa;
|
|
int xlen;
|
|
|
|
/*
|
|
* Get the DVMA mapping for this segment.
|
|
* XXX - Should separate allocation and mapin.
|
|
*/
|
|
data_pa = dvma_kvtopa(dh->dh_dvma, sc->sc_adapter_type);
|
|
data_pa += (ncr_sc->sc_dataptr - dh->dh_addr);
|
|
if (data_pa & 1)
|
|
panic("si_dma_start: bad pa=0x%lx", data_pa);
|
|
xlen = ncr_sc->sc_datalen;
|
|
xlen &= ~1; /* XXX: necessary? */
|
|
sc->sc_reqlen = xlen; /* XXX: or less? */
|
|
|
|
#ifdef DEBUG
|
|
if (si_debug & 2) {
|
|
printf("si_dma_setup: dh=%p, pa=0x%lx, xlen=0x%x\n",
|
|
dh, data_pa, xlen);
|
|
}
|
|
#endif
|
|
|
|
/* Set direction (send/recv) */
|
|
if (dh->dh_flags & SIDH_OUT) {
|
|
si->si_csr |= SI_CSR_SEND;
|
|
} else {
|
|
si->si_csr &= ~SI_CSR_SEND;
|
|
}
|
|
|
|
/* Reset the FIFO. */
|
|
si->si_csr &= ~SI_CSR_FIFO_RES; /* active low */
|
|
si->si_csr |= SI_CSR_FIFO_RES;
|
|
|
|
if (data_pa & 2) {
|
|
si->si_csr |= SI_CSR_BPCON;
|
|
} else {
|
|
si->si_csr &= ~SI_CSR_BPCON;
|
|
}
|
|
|
|
/* Load the start address. */
|
|
si->dma_addrh = (ushort)(data_pa >> 16);
|
|
si->dma_addrl = (ushort)(data_pa & 0xFFFF);
|
|
|
|
/*
|
|
* Keep the count zero or it may start early!
|
|
*/
|
|
si->dma_counth = 0;
|
|
si->dma_countl = 0;
|
|
|
|
#if 0
|
|
/* Clear FIFO counter. (also hits dma_count) */
|
|
si->fifo_cnt_hi = 0;
|
|
si->fifo_count = 0;
|
|
#endif
|
|
}
|
|
|
|
|
|
void
|
|
si_vme_dma_start(ncr_sc)
|
|
struct ncr5380_softc *ncr_sc;
|
|
{
|
|
struct si_softc *sc = (struct si_softc *)ncr_sc;
|
|
struct sci_req *sr = ncr_sc->sc_current;
|
|
struct si_dma_handle *dh = sr->sr_dma_hand;
|
|
volatile struct si_regs *si = sc->sc_regs;
|
|
int s, xlen;
|
|
|
|
xlen = sc->sc_reqlen;
|
|
|
|
/* This MAY be time critical (not sure). */
|
|
s = splhigh();
|
|
|
|
si->dma_counth = (ushort)(xlen >> 16);
|
|
si->dma_countl = (ushort)(xlen & 0xFFFF);
|
|
|
|
/* Set it anyway, even though dma_count hits it. */
|
|
si->fifo_cnt_hi = (ushort)(xlen >> 16);
|
|
si->fifo_count = (ushort)(xlen & 0xFFFF);
|
|
|
|
/*
|
|
* Acknowledge the phase change. (After DMA setup!)
|
|
* Put the SBIC into DMA mode, and start the transfer.
|
|
*/
|
|
if (dh->dh_flags & SIDH_OUT) {
|
|
*ncr_sc->sci_tcmd = PHASE_DATA_OUT;
|
|
SCI_CLR_INTR(ncr_sc);
|
|
*ncr_sc->sci_icmd = SCI_ICMD_DATA;
|
|
*ncr_sc->sci_mode |= (SCI_MODE_DMA | SCI_MODE_DMA_IE);
|
|
*ncr_sc->sci_dma_send = 0; /* start it */
|
|
} else {
|
|
*ncr_sc->sci_tcmd = PHASE_DATA_IN;
|
|
SCI_CLR_INTR(ncr_sc);
|
|
*ncr_sc->sci_icmd = 0;
|
|
*ncr_sc->sci_mode |= (SCI_MODE_DMA | SCI_MODE_DMA_IE);
|
|
*ncr_sc->sci_irecv = 0; /* start it */
|
|
}
|
|
|
|
/* Let'er rip! */
|
|
si->si_csr |= SI_CSR_DMA_EN;
|
|
|
|
splx(s);
|
|
ncr_sc->sc_state |= NCR_DOINGDMA;
|
|
|
|
#ifdef DEBUG
|
|
if (si_debug & 2) {
|
|
printf("si_dma_start: started, flags=0x%x\n",
|
|
ncr_sc->sc_state);
|
|
}
|
|
#endif
|
|
}
|
|
|
|
|
|
void
|
|
si_vme_dma_eop(ncr_sc)
|
|
struct ncr5380_softc *ncr_sc;
|
|
{
|
|
|
|
/* Not needed - DMA was stopped prior to examining sci_csr */
|
|
}
|
|
|
|
|
|
void
|
|
si_vme_dma_stop(ncr_sc)
|
|
struct ncr5380_softc *ncr_sc;
|
|
{
|
|
struct si_softc *sc = (struct si_softc *)ncr_sc;
|
|
struct sci_req *sr = ncr_sc->sc_current;
|
|
struct si_dma_handle *dh = sr->sr_dma_hand;
|
|
volatile struct si_regs *si = sc->sc_regs;
|
|
int resid, ntrans;
|
|
|
|
if ((ncr_sc->sc_state & NCR_DOINGDMA) == 0) {
|
|
#ifdef DEBUG
|
|
printf("si_dma_stop: dma not running\n");
|
|
#endif
|
|
return;
|
|
}
|
|
ncr_sc->sc_state &= ~NCR_DOINGDMA;
|
|
|
|
/* First, halt the DMA engine. */
|
|
si->si_csr &= ~SI_CSR_DMA_EN; /* VME only */
|
|
|
|
/* Set an impossible phase to prevent data movement? */
|
|
*ncr_sc->sci_tcmd = PHASE_INVALID;
|
|
|
|
if (si->si_csr & (SI_CSR_DMA_CONFLICT | SI_CSR_DMA_BUS_ERR)) {
|
|
printf("si: DMA error, csr=0x%x, reset\n", si->si_csr);
|
|
sr->sr_xs->error = XS_DRIVER_STUFFUP;
|
|
ncr_sc->sc_state |= NCR_ABORTING;
|
|
si_vme_reset(ncr_sc);
|
|
goto out;
|
|
}
|
|
|
|
/* Note that timeout may have set the error flag. */
|
|
if (ncr_sc->sc_state & NCR_ABORTING)
|
|
goto out;
|
|
|
|
/* XXX: Wait for DMA to actually finish? */
|
|
|
|
/*
|
|
* Now try to figure out how much actually transferred
|
|
*
|
|
* The fifo_count does not reflect how many bytes were
|
|
* actually transferred for VME.
|
|
*
|
|
* SCSI-3 VME interface is a little funny on writes:
|
|
* if we have a disconnect, the dma has overshot by
|
|
* one byte and the resid needs to be incremented.
|
|
* Only happens for partial transfers.
|
|
* (Thanks to Matt Jacob)
|
|
*/
|
|
|
|
resid = si->fifo_count & 0xFFFF;
|
|
if (dh->dh_flags & SIDH_OUT)
|
|
if ((resid > 0) && (resid < sc->sc_reqlen))
|
|
resid++;
|
|
ntrans = sc->sc_reqlen - resid;
|
|
|
|
#ifdef DEBUG
|
|
if (si_debug & 2) {
|
|
printf("si_dma_stop: resid=0x%x ntrans=0x%x\n",
|
|
resid, ntrans);
|
|
}
|
|
#endif
|
|
|
|
if (ntrans < MIN_DMA_LEN) {
|
|
printf("si: fifo count: 0x%x\n", resid);
|
|
ncr_sc->sc_state |= NCR_ABORTING;
|
|
goto out;
|
|
}
|
|
if (ntrans > ncr_sc->sc_datalen)
|
|
panic("si_dma_stop: excess transfer");
|
|
|
|
/* Adjust data pointer */
|
|
ncr_sc->sc_dataptr += ntrans;
|
|
ncr_sc->sc_datalen -= ntrans;
|
|
|
|
/*
|
|
* After a read, we may need to clean-up
|
|
* "Left-over bytes" (yuck!)
|
|
*/
|
|
if (((dh->dh_flags & SIDH_OUT) == 0) &&
|
|
((si->si_csr & SI_CSR_LOB) != 0))
|
|
{
|
|
char *cp = ncr_sc->sc_dataptr;
|
|
#ifdef DEBUG
|
|
printf("si: Got Left-over bytes!\n");
|
|
#endif
|
|
if (si->si_csr & SI_CSR_BPCON) {
|
|
/* have SI_CSR_BPCON */
|
|
cp[-1] = (si->si_bprl & 0xff00) >> 8;
|
|
} else {
|
|
switch (si->si_csr & SI_CSR_LOB) {
|
|
case SI_CSR_LOB_THREE:
|
|
cp[-3] = (si->si_bprh & 0xff00) >> 8;
|
|
cp[-2] = (si->si_bprh & 0x00ff);
|
|
cp[-1] = (si->si_bprl & 0xff00) >> 8;
|
|
break;
|
|
case SI_CSR_LOB_TWO:
|
|
cp[-2] = (si->si_bprh & 0xff00) >> 8;
|
|
cp[-1] = (si->si_bprh & 0x00ff);
|
|
break;
|
|
case SI_CSR_LOB_ONE:
|
|
cp[-1] = (si->si_bprh & 0xff00) >> 8;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
out:
|
|
si->dma_addrh = 0;
|
|
si->dma_addrl = 0;
|
|
|
|
si->dma_counth = 0;
|
|
si->dma_countl = 0;
|
|
|
|
si->fifo_cnt_hi = 0;
|
|
si->fifo_count = 0;
|
|
|
|
/* Put SBIC back in PIO mode. */
|
|
*ncr_sc->sci_mode &= ~(SCI_MODE_DMA | SCI_MODE_DMA_IE);
|
|
*ncr_sc->sci_icmd = 0;
|
|
}
|