NetBSD/sys/arch/mac68k/include/psc.h

107 lines
4.5 KiB
C

/* $NetBSD: psc.h,v 1.2 1997/11/07 13:31:21 briggs Exp $ */
/*-
* Copyright (c) 1997 David Huang <khym@bga.com>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*/
/*
* Some register definitions for the PSC, present only on the
* Centris/Quadra 660av and the Quadra 840av.
*/
extern volatile u_int8_t *PSCBase;
#define psc_reg1(r) (*((volatile u_int8_t *)(PSCBase+r)))
#define psc_reg2(r) (*((volatile u_int16_t *)(PSCBase+r)))
#define psc_reg4(r) (*((volatile u_int32_t *)(PSCBase+r)))
int add_psc_lev3_intr __P((void (*)(void *), void *));
int add_psc_lev4_intr __P((int, int (*)(void *), void *));
int add_psc_lev5_intr __P((int, void (*)(void *), void *));
int add_psc_lev6_intr __P((int, void (*)(void *), void *));
int remove_psc_lev3_intr __P((void));
int remove_psc_lev4_intr __P((int));
int remove_psc_lev5_intr __P((int));
int remove_psc_lev6_intr __P((int));
/*
* Reading an interrupt status register returns a mask of the
* currently interrupting devices (one bit per device). Reading an
* interrupt enable register returns a mask of the currently enabled
* devices. Writing an interrupt enable register with the MSB set
* enables the interrupts in the lower 4 bits, while writing with the
* MSB clear disables the corresponding interrupts.
* e.g. write 0x81 to enable device 0, write 0x86 to enable devices 1
* and 2, write 0x02 to disable device 1.
*
* Level 3 device 0 is MACE
* Level 4 device 0 is 3210 DSP?
* Level 4 device 1 is SCC channel A (modem port)
* Level 4 device 2 is SCC channel B (printer port)
* Level 4 device 3 is MACE DMA completion
* Level 5 device 0 is 3210 DSP?
* Level 5 device 1 is 3210 DSP?
* Level 6 device 0 is ?
* Level 6 device 1 is ?
* Level 6 device 2 is ?
*/
/* PSC interrupt registers */
#define PSC_LEV3_ISR 0x130 /* level 3 interrupt status register */
#define PSC_LEV3_IER 0x134 /* level 3 interrupt enable register */
#define PSCINTR_ENET 0 /* Ethernet interrupt */
#define PSC_LEV4_ISR 0x140 /* level 4 interrupt status register */
#define PSC_LEV4_IER 0x144 /* level 4 interrupt enable register */
#define PSCINTR_SCCA 1 /* SCC channel A interrupt */
#define PSCINTR_SCCB 2 /* SCC channel B interrupt */
#define PSCINTR_ENET_DMA 3 /* Ethernet DMA completion interrupt */
#define PSC_LEV5_ISR 0x150 /* level 5 interrupt status register */
#define PSC_LEV5_IER 0x154 /* level 5 interrupt enable register */
#define PSC_LEV6_ISR 0x160 /* level 6 interrupt status register */
#define PSC_LEV6_IER 0x164 /* level 6 interrupt enable register */
/* PSC DMA channel control registers */
#define PSC_ENETRD_CTL 0xc10 /* MACE receive DMA channel control/status */
#define PSC_ENETWR_CTL 0xc20 /* MACE transmit DMA channel control/status */
/* PSC DMA channels */
#define PSC_ENETRD_ADDR 0x1020 /* MACE receive DMA address register */
#define PSC_ENETRD_LEN 0x1024 /* MACE receive DMA buffer count */
#define PSC_ENETRD_CMD 0x1028 /* MACE receive DMA command register */
#define PSC_ENETWR_ADDR 0x1040 /* MACE transmit DMA address register */
#define PSC_ENETWR_LEN 0x1044 /* MACE transmit DMA length */
#define PSC_ENETWR_CMD 0x1048 /* MACE transmit DMA command register */
/*
* PSC DMA channels are controlled by two sets of registers (see p.29
* of the Quadra 840av and Centris 660av Developer Note). Add the
* following offsets to get the desired register set.
*/
#define PSC_SET0 0x00
#define PSC_SET1 0x10