164 lines
5.3 KiB
Plaintext
164 lines
5.3 KiB
Plaintext
.\" $NetBSD: prep,v 1.17 1999/01/13 07:30:02 ross Exp $
|
|
.Pp
|
|
You will need an AmigaDOS hard drive prep tool to prepare your hard
|
|
drives for use with NetBSD/Amiga. HDToolBox is provided with the
|
|
system software and on floppy installation disks since Release 2.0
|
|
of AmigaDOS, so we will provide instructions for its use.
|
|
.
|
|
.Ss2 "Preparing your hard disk with HDToolBox"
|
|
.
|
|
.Pp
|
|
A full explanation of HDToolBox can be found with your
|
|
AmigaDOS manuals and is beyond the scope of this document.
|
|
.Pp
|
|
The first time you partition a drive, you need to set its drive
|
|
type so that you have working geometry parameters. To do this
|
|
you enter the "Change drive type" menu, and either use "read
|
|
parameters from drive" or set them manually.
|
|
.Pp
|
|
Note you will be modifying your HD's. If you mess something
|
|
up here you could lose everything on all the drives that
|
|
you configure. It is therefore advised that you:
|
|
.Bl -enum
|
|
.It
|
|
Write down your current configurations. Do this
|
|
by examining each partition on the drive and the
|
|
drives parameters (from Change drive type.)
|
|
.It
|
|
Back up the partitions you are keeping.
|
|
.El
|
|
What you need to do is partition your drives; creating at least
|
|
root, swap and /usr partitions and possibly at least one more for
|
|
/usr/local if you have the space.
|
|
.Pp
|
|
This should be done as the HDToolBox manual describes. One thing
|
|
to note is that if you are not using a Commodore controller you
|
|
will need to specify the device your SCSI controller uses, e.g.
|
|
if you have a Warp Engine you would:
|
|
.Pp
|
|
from cli,
|
|
.Dl "hdtoolbox warpdrive.device"
|
|
.Pp
|
|
from wb set the tooltype,
|
|
.Dl "SCSI_DEVICE_NAME=warpdrive.device"
|
|
.Pp
|
|
The important things you need to do above and beyond normal
|
|
partitioning includes (from Partition Drive section):
|
|
.Bl -enum
|
|
.It
|
|
Marking all NetBSD partitions as non-bootable, with
|
|
two exceptions: the root partition, if you want to boot
|
|
NetBSD directly, or the swap partition, if you want
|
|
to boot the installation miniroot directly.
|
|
.It
|
|
Changing the file system parameters of the partitions
|
|
to NetBSD ones. This must be done from the
|
|
partitioning section and `Advanced options' must
|
|
be enabled.
|
|
.El
|
|
.Pp
|
|
To Make the needed changes:
|
|
.Pp
|
|
.Bl -bullet -compact
|
|
.It
|
|
Click the `Adv. Options' button
|
|
.It
|
|
Click the `Change file system' button
|
|
.It
|
|
Choose `Custom File System'
|
|
.It
|
|
Turn off `Automount' if on.
|
|
.It
|
|
Set the dostype to one of these three choices:
|
|
.Bd -literal -offset indent
|
|
root partition : 0x4e425207
|
|
swap partition : 0x4e425301
|
|
other partitions: 0x4e425507
|
|
.Ed
|
|
.Pp
|
|
Here `other' refers to other partitions you will
|
|
format for reading and writing under NetBSD (e.g.
|
|
/usr)
|
|
.Pp
|
|
Make sure you hit the return key to enter this value
|
|
as some versions of HDToolBox will forget your entry
|
|
if you don't.
|
|
.It
|
|
Turn custom boot code off
|
|
.It
|
|
Set Reserved Blocks start and end to 0.
|
|
.It
|
|
Click Ok.
|
|
.El
|
|
.Pp
|
|
On the root (and, for installation, swap) partition,
|
|
set instead this:
|
|
.Pp
|
|
.Bl -bullet -compact
|
|
.It
|
|
Turn custom boot code on
|
|
.It
|
|
Set Reserved Blocks start and end to 0.
|
|
.It
|
|
Set Number of Custom Boot Blocks to 16
|
|
.It
|
|
Set Automount This Partition on
|
|
.It
|
|
Click Ok.
|
|
.Pp
|
|
Mask and maxtransfer are not used with NetBSD.
|
|
.El
|
|
.Pp
|
|
Once this is done NetBSD/Amiga will be able to recognize your
|
|
disks and which partitions it should use.
|
|
.
|
|
.Ss2 "Transferring the miniroot file system"
|
|
.
|
|
The NetBSD/Amiga installation or upgrade now uses a "miniroot"
|
|
file system which is installed on the partition used by NetBSD
|
|
for swapping. This removes the requirement of using a floppy
|
|
disk for the file system used by the installation or upgrade
|
|
process. It also allows more utilities to be present on the
|
|
file system than would be available when using an 880K floppy
|
|
disk.
|
|
.Pp
|
|
Once the hard disk has been prepared for NetBSD, the miniroot
|
|
file system (miniroot.fs) is transferred to the swap
|
|
partition configured during the hard disk prep (or the existing
|
|
swap partition in the case of an upgrade). The xstreamtodev
|
|
utility provided in the "amiga/installation/misc" directory can
|
|
be used on AmigaDOS to transfer the file system for either a new
|
|
installation or an upgrade. The file system can also be
|
|
transferred on an existing NetBSD system for an update by
|
|
using dd. This should only be done after booting NetBSD
|
|
into single-user state. It may also be possible to shutdown
|
|
to single-user, providing that the single-user state processes
|
|
are not using the swap partition.
|
|
.Pp
|
|
On AmigaDOS, the command:
|
|
.Dl "xstreamtodev --input=miniroot.fs --rdb-name=\*<swap partition\*>"
|
|
where \*<swap partition\*> is the name you gave to the NetBSD
|
|
partition to be used for swapping. If xstreamtodev is unable
|
|
to determine the SCSI driver device name or the unit number
|
|
of the specified partition, you may also need to include the
|
|
option
|
|
.Dl --device=\*<driver.name\*>
|
|
and/or
|
|
.Dl --unit=\*<SCSI unit number\*>
|
|
.Pp
|
|
To transfer the miniroot using NetBSD, you should be booted up
|
|
in single user state on the current NetBSD system, or use the
|
|
"shutdown now" command to shutdown to single-user state. Then
|
|
copy the miniroot using dd:
|
|
.Dl dd if=miniroot.fs of=/dev/rsd0b
|
|
where
|
|
.Pa /dev/rsd0b
|
|
should be the device path of the swap partition
|
|
your system is configured to use. Once the file is copied,
|
|
reboot back to AmigaDOS to boot the upgrade kernel.
|
|
.(tag Em Caveat:
|
|
Once you have started installation, if you abort it
|
|
and want to retry you must reinstall the miniroot.fs on the swap
|
|
partition.
|
|
.tag)
|