9604e7689d
- Add support for byte system bus mode. Based on patch in kern/17193 by Christian Groessler, with some improvements by me. - Rename sc_flags in mb86960_softc to sc_stat, rename "type" to sc_flags to specify controller quirks and remove enum mb86960_type. - Pass controller type via new sc_flags in mb86960_softc rather than via an mb86960_attach() arg. - Handle unaligned mbufs properly in mb86960_write_mbufs(). (from ne2000.c) - Fix a signed/unsigned comparision warning. - Add definitions of status bits in the RX packed header. - Change types of some members in mb86960_softc.
361 lines
13 KiB
C
361 lines
13 KiB
C
/* $NetBSD: mb86960reg.h,v 1.8 2002/11/30 14:15:10 tsutsui Exp $ */
|
|
|
|
/*
|
|
* All Rights Reserved, Copyright (C) Fujitsu Limited 1995
|
|
*
|
|
* This software may be used, modified, copied, distributed, and sold, in
|
|
* both source and binary form provided that the above copyright, these
|
|
* terms and the following disclaimer are retained. The name of the author
|
|
* and/or the contributor may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
/*
|
|
* Registers of Fujitsu MB86960A/MB86965A Ethernet controller.
|
|
* Written and contributed by M.S. <seki@sysrap.cs.fujitsu.co.jp>
|
|
*/
|
|
|
|
/*
|
|
* Notes on register naming:
|
|
*
|
|
* Fujitsu documents for MB86960A/MB86965A uses no mnemorable names
|
|
* for their registers. They defined only three names for 32
|
|
* registers and appended numbers to distinguish registers of
|
|
* same name. Surprisingly, the numbers represent I/O address
|
|
* offsets of the registers from the base addresses, and their
|
|
* names correspond to the "bank" the registers are allocated.
|
|
* All this means that, for example, to say "read DLCR8" has no more
|
|
* than to say "read a register at offset 8 on bank DLCR."
|
|
*
|
|
* The following definitions may look silly, but that's what Fujitsu
|
|
* did, and it is necessary to know these names to read Fujitsu
|
|
* documents..
|
|
*/
|
|
|
|
/* Data Link Control Registrs, on invaliant port addresses. */
|
|
#define FE_DLCR0 0
|
|
#define FE_DLCR1 1
|
|
#define FE_DLCR2 2
|
|
#define FE_DLCR3 3
|
|
#define FE_DLCR4 4
|
|
#define FE_DLCR5 5
|
|
#define FE_DLCR6 6
|
|
#define FE_DLCR7 7
|
|
|
|
/* More DLCRs, on register bank #0. */
|
|
#define FE_DLCR8 8
|
|
#define FE_DLCR9 9
|
|
#define FE_DLCR10 10
|
|
#define FE_DLCR11 11
|
|
#define FE_DLCR12 12
|
|
#define FE_DLCR13 13
|
|
#define FE_DLCR14 14
|
|
#define FE_DLCR15 15
|
|
|
|
/* Malticast Address Registers. On register bank #1. */
|
|
#define FE_MAR8 8
|
|
#define FE_MAR9 9
|
|
#define FE_MAR10 10
|
|
#define FE_MAR11 11
|
|
#define FE_MAR12 12
|
|
#define FE_MAR13 13
|
|
#define FE_MAR14 14
|
|
#define FE_MAR15 15
|
|
|
|
/* Buffer Memory Port Registers. On register bank #2. */
|
|
#define FE_BMPR8 8
|
|
#define FE_BMPR9 9
|
|
#define FE_BMPR10 10
|
|
#define FE_BMPR11 11
|
|
#define FE_BMPR12 12
|
|
#define FE_BMPR13 13
|
|
#define FE_BMPR14 14
|
|
#define FE_BMPR15 15
|
|
|
|
/* More BMPRs, only on MB86965A, accessible only when JLI mode. */
|
|
#define FE_BMPR16 16
|
|
#define FE_BMPR17 17
|
|
#define FE_BMPR18 18
|
|
#define FE_BMPR19 19
|
|
|
|
#define FE_RESET 31
|
|
|
|
/*
|
|
* Definitions of registers.
|
|
* I don't have Fujitsu documents of MB86960A/MB86965A, so I don't
|
|
* know the official names for each flags and fields. The following
|
|
* names are assigned by me (the author of this file,) since I cannot
|
|
* mnemorize hexadecimal constants for all of these functions.
|
|
* Comments? FIXME.
|
|
*/
|
|
|
|
/* DLCR0 -- transmitter status */
|
|
#define FE_D0_BUSERR 0x01 /* Bus write error */
|
|
#define FE_D0_COLL16 0x02 /* Collision limit (16) encountered */
|
|
#define FE_D0_COLLID 0x04 /* Collision on last transmission */
|
|
#define FE_D0_JABBER 0x08 /* Jabber */
|
|
#define FE_D0_CRLOST 0x10 /* Carrier lost on last transmission */
|
|
#define FE_D0_PKTRCD 0x20 /* No corrision on last transmission */
|
|
#define FE_D0_NETBSY 0x40 /* Network Busy (Carrier Detected) */
|
|
#define FE_D0_TXDONE 0x80 /* Transmission complete */
|
|
|
|
/* DLCR1 -- receiver status */
|
|
#define FE_D1_OVRFLO 0x01 /* Receiver buffer overflow */
|
|
#define FE_D1_CRCERR 0x02 /* CRC error on last packet */
|
|
#define FE_D1_ALGERR 0x04 /* Alignment error on last packet */
|
|
#define FE_D1_SRTPKT 0x08 /* Short (RUNT) packet is received */
|
|
#define FE_D1_RMTRST 0x10 /* Remote reset packet (type = 0x0900) */
|
|
#define FE_D1_DMAEOP 0x20 /* Host asserted End of DMA OPeration */
|
|
#define FE_D1_BUSERR 0x40 /* Bus read error */
|
|
#define FE_D1_PKTRDY 0x80 /* Packet(s) ready on receive buffer */
|
|
|
|
#define FE_D1_ERRBITS "\20\4SRTPKT\3ALGERR\2CRCERR\1OVRFLO"
|
|
|
|
/* DLCR2 -- transmitter interrupt control; same layout as DLCR0 */
|
|
#define FE_D2_BUSERR FE_D0_BUSERR
|
|
#define FE_D2_COLL16 FE_D0_COLL16
|
|
#define FE_D2_COLLID FE_D0_COLLID
|
|
#define FE_D2_JABBER FE_D0_JABBER
|
|
#define FE_D2_TXDONE FE_D0_TXDONE
|
|
|
|
#define FE_D2_RESERVED 0x70
|
|
|
|
/* DLCR3 -- receiver interrupt control; same layout as DLCR1 */
|
|
#define FE_D3_OVRFLO FE_D1_OVRFLO
|
|
#define FE_D3_CRCERR FE_D1_CRCERR
|
|
#define FE_D3_ALGERR FE_D1_ALGERR
|
|
#define FE_D3_SRTPKT FE_D1_SRTPKT
|
|
#define FE_D3_RMTRST FE_D1_RMTRST
|
|
#define FE_D3_DMAEOP FE_D1_DMAEOP
|
|
#define FE_D3_BUSERR FE_D1_BUSERR
|
|
#define FE_D3_PKTRDY FE_D1_PKTRDY
|
|
|
|
/* DLCR4 -- transmitter operation mode */
|
|
#define FE_D4_DSC 0x01 /* Disable carrier sense on trans. */
|
|
#define FE_D4_LBC 0x02 /* Loop back test control */
|
|
#define FE_D4_CNTRL 0x04 /* - ??? */
|
|
#define FE_D4_TEST1 0x08 /* Test output #1 */
|
|
#define FE_D4_COL 0xF0 /* Collision counter */
|
|
|
|
#define FE_D4_LBC_ENABLE 0x00 /* Perform loop back test */
|
|
#define FE_D4_LBC_DISABLE 0x02 /* Normal operation */
|
|
|
|
#define FE_D4_COL_SHIFT 4
|
|
|
|
/* DLCR5 -- receiver operation mode */
|
|
#define FE_D5_AFM0 0x01 /* Receive packets for other stations */
|
|
#define FE_D5_AFM1 0x02 /* Receive packets for this station */
|
|
#define FE_D5_RMTRST 0x04 /* Enable remote reset operation */
|
|
#define FE_D5_SRTPKT 0x08 /* Accept short (RUNT) packets */
|
|
#define FE_D5_SRTADR 0x10 /* Short (16 bits?) MAC address */
|
|
#define FE_D5_BADPKT 0x20 /* Accept packets with error */
|
|
#define FE_D5_BUFEMP 0x40 /* Receive buffer is empty */
|
|
#define FE_D5_TEST2 0x80 /* Test output #2 */
|
|
|
|
/* DLCR6 -- hardware configuration #0 */
|
|
#define FE_D6_BUFSIZ 0x03 /* Size of NIC buffer SRAM */
|
|
#define FE_D6_TXBSIZ 0x0C /* Size (and config)of trans. buffer */
|
|
#define FE_D6_BBW 0x10 /* Buffer SRAM bus width */
|
|
#define FE_D6_SBW 0x20 /* System bus width */
|
|
#define FE_D6_SRAM 0x40 /* Buffer SRAM access time */
|
|
#define FE_D6_DLC 0x80 /* Disable DLC (recever/transmitter) */
|
|
|
|
#define FE_D6_BUFSIZ_8KB 0x00 /* The board has 8KB SRAM */
|
|
#define FE_D6_BUFSIZ_16KB 0x01 /* The board has 16KB SRAM */
|
|
#define FE_D6_BUFSIZ_32KB 0x02 /* The board has 32KB SRAM */
|
|
#define FE_D6_BUFSIZ_64KB 0x03 /* The board has 64KB SRAM */
|
|
|
|
#define FE_D6_TXBSIZ_1x2KB 0x00 /* Single 2KB buffer for trans. */
|
|
#define FE_D6_TXBSIZ_2x2KB 0x04 /* Double 2KB buffers */
|
|
#define FE_D6_TXBSIZ_2x4KB 0x08 /* Double 4KB buffers */
|
|
#define FE_D6_TXBSIZ_2x8KB 0x0C /* Double 8KB buffers */
|
|
|
|
#define FE_D6_BBW_WORD 0x00 /* SRAM has 16 bit data line */
|
|
#define FE_D6_BBW_BYTE 0x10 /* SRAM has 8 bit data line */
|
|
|
|
#define FE_D6_SBW_WORD 0x00 /* Access with 16 bit (AT) bus */
|
|
#define FE_D6_SBW_BYTE 0x20 /* Access with 8 bit (XT) bus */
|
|
|
|
#define FE_D6_SRAM_150ns 0x00 /* The board has slow SRAM */
|
|
#define FE_D6_SRAM_100ns 0x40 /* The board has fast SRAM */
|
|
|
|
#define FE_D6_DLC_ENABLE 0x00 /* Normal operation */
|
|
#define FE_D6_DLC_DISABLE 0x80 /* Stop sending/receiving */
|
|
|
|
/* DLC7 -- hardware configuration #1 */
|
|
#define FE_D7_BYTSWP 0x01 /* Host byte order control */
|
|
#define FE_D7_EOPPOL 0x02 /* Polarity of DMA EOP signal */
|
|
#define FE_D7_RBS 0x0C /* Register bank select */
|
|
#define FE_D7_RDYPNS 0x10 /* Senses RDYPNSEL input signal */
|
|
#define FE_D7_POWER 0x20 /* Stand-by (power down) mode control */
|
|
#define FE_D7_ED 0xC0 /* Encoder/Decoder config (for MB86960) */
|
|
#define FE_D7_IDENT 0xC0 /* Chip identification */
|
|
|
|
#define FE_D7_BYTSWP_LH 0x00 /* DEC/Intel byte order */
|
|
#define FE_D7_BYTSWP_HL 0x01 /* IBM/Motorolla byte order */
|
|
|
|
#define FE_D7_RBS_DLCR 0x00 /* Select DLCR8-15 */
|
|
#define FE_D7_RBS_MAR 0x04 /* Select MAR8-15 */
|
|
#define FE_D7_RBS_BMPR 0x08 /* Select BMPR8-15 */
|
|
|
|
#define FE_D7_POWER_DOWN 0x00 /* Power down (stand-by) mode */
|
|
#define FE_D7_POWER_UP 0x20 /* Normal operation */
|
|
|
|
#define FE_D7_ED_NORMAL 0x00 /* Normal NICE */
|
|
#define FE_D7_ED_MON 0x40 /* NICE + Monitor */
|
|
#define FE_D7_ED_BYPASS 0x80 /* Encoder/Decorder Bypass */
|
|
#define FE_D7_ED_TEST 0xC0 /* Encoder/Decorder Test */
|
|
|
|
#define FE_D7_IDENT_86960 0x00 /* MB86960 (NICE) */
|
|
#define FE_D7_IDENT_86964 0x40 /* MB86964 */
|
|
#define FE_D7_IDENT_86967 0x80 /* MB86967 */
|
|
#define FE_D7_IDENT_86965 0xC0 /* MB86965 (EtherCoupler) */
|
|
|
|
/* DLCR8 thru DLCR13 are for Ethernet station address. */
|
|
|
|
/* DLCR14 and DLCR15 are for TDR (Time Domain Reflectometry). */
|
|
|
|
/* MAR8 thru MAR15 are for Multicast address filter. */
|
|
|
|
/* BMPR8 and BMPR9 are for packet data. */
|
|
|
|
/* BMPR10 -- transmitter start trigger */
|
|
#define FE_B10_START 0x80 /* Start transmitter */
|
|
#define FE_B10_COUNT 0x7F /* Packet count */
|
|
|
|
/* BMPR11 -- 16 collisions control */
|
|
#define FE_B11_CTRL 0x01 /* Skip or resend errored packets */
|
|
#define FE_B11_MODE1 0x02 /* Restart transmitter after COLL16 */
|
|
#define FE_B11_MODE2 0x04 /* Automatic restart enable */
|
|
|
|
#define FE_B11_CTRL_RESEND 0x00 /* Re-send the collided packet */
|
|
#define FE_B11_CTRL_SKIP 0x01 /* Skip the collided packet */
|
|
|
|
/* BMPR12 -- DMA enable */
|
|
#define FE_B12_TXDMA 0x01 /* Enable transmitter DMA */
|
|
#define FE_B12_RXDMA 0x02 /* Enable receiver DMA */
|
|
|
|
/* BMPR13 -- DMA control */
|
|
#define FE_B13_BSTCTL 0x03 /* DMA burst mode control */
|
|
#define FE_B13_TPTYPE 0x04 /* Twisted pair cable impedance */
|
|
#define FE_B13_PORT 0x18 /* Port (TP/AUI) selection */
|
|
#define FE_B13_LNKTST 0x20 /* Link test enable */
|
|
#define FE_B13_SQTHLD 0x40 /* Lower squelch threshold */
|
|
#define FE_B13_IOUNLK 0x80 /* Change I/O base address */
|
|
|
|
#define FE_B13_BSTCTL_1 0x00
|
|
#define FE_B13_BSTCTL_4 0x01
|
|
#define FE_B13_BSTCTL_8 0x02
|
|
#define FE_B13_BSTCLT_12 0x03
|
|
|
|
#define FE_B13_TPTYPE_UTP 0x00 /* Unshielded (standard) cable */
|
|
#define FE_B13_TPTYPE_STP 0x04 /* Shielded (IBM) cable */
|
|
|
|
#define FE_B13_PORT_AUTO 0x00 /* Auto detected */
|
|
#define FE_B13_PORT_TP 0x08 /* Force TP */
|
|
#define FE_B13_PORT_AUI 0x18 /* Force AUI */
|
|
|
|
/* BMPR14 -- More receiver control and more transmission interrupts */
|
|
#define FE_B14_FILTER 0x01 /* Filter out self-originated packets */
|
|
#define FE_B14_SQE 0x02 /* SQE interrupt enable */
|
|
#define FE_B14_SKIP 0x04 /* Skip a received packet */
|
|
#define FE_B14_RJAB 0x20 /* RJAB interrupt enable */
|
|
#define FE_B14_LLD 0x40 /* Local-link-down interrupt enable */
|
|
#define FE_B14_RLD 0x80 /* Remote-link-down interrupt enable */
|
|
|
|
/* BMPR15 -- More transmitter status; basically same layout as BMPR14 */
|
|
#define FE_B15_SQE FE_B14_SQE
|
|
#define FE_B15_RCVPOL 0x08 /* Reversed receive line polarity */
|
|
#define FE_B15_RMTPRT 0x10 /* ??? */
|
|
#define FE_B15_RAJB FE_B14_RJAB
|
|
#define FE_B15_LLD FE_B14_LLD
|
|
#define FE_B15_RLD FE_B14_RLD
|
|
|
|
/* BMPR16 -- EEPROM control */
|
|
#define FE_B16_DOUT 0x04 /* EEPROM Data in (CPU to EEPROM) */
|
|
#define FE_B16_SELECT 0x20 /* EEPROM chip select */
|
|
#define FE_B16_CLOCK 0x40 /* EEPROM shift clock */
|
|
#define FE_B16_DIN 0x80 /* EEPROM data out (EEPROM to CPU) */
|
|
|
|
/* BMPR17 -- EEPROM data */
|
|
#define FE_B17_DATA 0x80 /* EEPROM data bit */
|
|
|
|
/* BMPR18 I/O Base Address (Only JLI mode) */
|
|
|
|
/* BMPR19 -- Jumperless Setting (Only JLI mode) */
|
|
#define FE_B19_IRQ 0xC0
|
|
#define FE_B19_IRQ_SHIFT 6
|
|
|
|
#define FE_B19_ROM 0x38
|
|
#define FE_B19_ROM_SHIFT 3
|
|
|
|
#define FE_B19_ADDR 0x07
|
|
#define FE_B19_ADDR_SHIFT 0
|
|
|
|
/*
|
|
* EEPROM specification (of JLI mode).
|
|
*/
|
|
|
|
/* Number of bytes in an EEPROM accessible through 86965. */
|
|
#define FE_EEPROM_SIZE 32
|
|
|
|
/* Offset for JLI config; automatically copied into BMPR19 at startup. */
|
|
#define FE_EEPROM_CONF 0x00
|
|
|
|
/* Delay for 93c06 EEPROM access */
|
|
#define FE_EEPROM_DELAY() DELAY(4)
|
|
|
|
/*
|
|
* EEPROM allocation of AT1700/RE2000.
|
|
*/
|
|
#define FE_ATI_EEP_ADDR 0x08 /* Station address (0x08-0x0d) */
|
|
#define FE_ATI_EEP_MEDIA 0x18 /* Media type */
|
|
#define FE_ATI_EEP_MAGIC 0x19 /* XXX Magic */
|
|
#define FE_ATI_EEP_MODEL 0x1e /* Hardware type */
|
|
#define FE_ATI_MODEL_AT1700T 0x00
|
|
#define FE_ATI_MODEL_AT1700BT 0x01
|
|
#define FE_ATI_MODEL_AT1700FT 0x02
|
|
#define FE_ATI_MODEL_AT1700AT 0x03
|
|
#define FE_ATI_EEP_REVISION 0x1f /* Hardware revision */
|
|
|
|
/*
|
|
* Some 86960 specific constants.
|
|
*/
|
|
|
|
/* Length (in bytes) of a Multicast Address Filter. */
|
|
#define FE_FILTER_LEN 8
|
|
|
|
/* How many packets we can put in the transmission buffer on NIC memory. */
|
|
#define FE_QUEUEING_MAX 127
|
|
|
|
/* Size (in bytes) of a "packet length" word in transmission buffer. */
|
|
#define FE_TXLEN_SIZE 2
|
|
|
|
/* receive packet status in the receive packet header. */
|
|
#define FE_RXSTAT_GOODPKT 0x20
|
|
#define FE_RXSTAT_RMT0900 0x10
|
|
#define FE_RXSTAT_SHORTPKT 0x08
|
|
#define FE_RXSTAT_ALIGNERR 0x04
|
|
#define FE_RXSTAT_CRCERR 0x02
|
|
|
|
/*
|
|
* FUJITSU MBH10302 specific Registers.
|
|
*/
|
|
|
|
#define FE_MBH0 0x10 /* Master interrupt register */
|
|
#define FE_MBH_ENADDR 0x1A /* Mac address */
|
|
#define FE_MBH0_MASK 0x0D
|
|
#define FE_MBH0_INTR_ENABLE 0x10 /* Enable interrupts */
|