187 lines
6.8 KiB
Plaintext
187 lines
6.8 KiB
Plaintext
.\" $NetBSD: xfer,v 1.6 2000/03/13 22:37:15 soren Exp $
|
|
.
|
|
Installation is supported from several media types, including:
|
|
.Bl -bullet -compact -offset indent
|
|
.It
|
|
Removable SCSI hard disk, or Magneto-Optical disk (MO)
|
|
.It
|
|
Tape
|
|
.It
|
|
Remote NFS partition
|
|
.It
|
|
FTP
|
|
.El
|
|
.Pp
|
|
You'll need to have a install floppy disk. On the first, you'll put
|
|
the install floppy image.
|
|
.Pp
|
|
If you are using a UN*X-like system to write the floppy images to
|
|
disks, you should use the
|
|
.Pa dd
|
|
command to copy the file system images (.fs files) directly to the raw
|
|
floppy disks. It is suggested that you read the dd(1) manual page or
|
|
ask your system administrator to determine the correct set of
|
|
arguments to use; it will be slightly different from system to system,
|
|
and a comprehensive list of the possibilities is beyond the scope of
|
|
this document.
|
|
.Pp
|
|
If you are using Human68k to write the floppy images to disks, you
|
|
should use the
|
|
.Pa rawrite
|
|
utility, provided in the
|
|
.Pa installation/misc
|
|
directory of the NetBSD distribution. It will write the file system
|
|
images (.fs files) to disks.
|
|
.Pp
|
|
If you can retrieve
|
|
.Pa loadbsd.x
|
|
utility and
|
|
.Pa netbsd.INSTALL
|
|
file which can be found in
|
|
.Pa installation/misc
|
|
directory into your Human68k disk, you can run installation kernel
|
|
without preparing the special boot floppy. Simply type:
|
|
.D1 Ic loadbsd netbsd.INSTALL
|
|
from the Human68k command line, then
|
|
.Nx
|
|
will start the installation sequence.
|
|
.Pp
|
|
Obviously, the steps necessary to prepare the distribution sets for
|
|
installation or upgrade depend on which installation medium you
|
|
choose. The steps for the various media are outlined below.
|
|
.Pp
|
|
.Bl -tag -width indent
|
|
.It Em Install\ From\ Removable\ SCSI\ Hard\ Disk\ or\ MO
|
|
.Pp
|
|
To install NetBSD from a removable device
|
|
the media
|
|
.Em must
|
|
be of the IBM
|
|
.Em Super-floppy
|
|
format. The Human68k format is not recognized
|
|
by this release of the NetBSD/\*m. If you have a MS-DOS (or
|
|
MS-Windows) machine with an MO drive connected, use it. If
|
|
you don't, and if you have a program to handle IBM format MO
|
|
for Human68k, copy all the files in the subdirectory
|
|
.Pa x68k/binaries
|
|
and CHANGE THEIR NAMES IN UPPER CASE.
|
|
.
|
|
.It Em Install\ From\ Tape
|
|
.Pp
|
|
To install or upgrade NetBSD using a tape, you need to do the
|
|
following:
|
|
.Pp
|
|
To install NetBSD from a tape, you need to make a tape that
|
|
contains the distribution set files, in "tar" format. If
|
|
you're making the tape on a UN*X-like system, the easiest way
|
|
to do so is probably something like:
|
|
.D1 Ic tar\ cf Ar tape_device Ar dist_directories
|
|
where
|
|
.Ar tape_device
|
|
is the name of the tape device that
|
|
describes the tape drive you're using (possibly /dev/rst0, or
|
|
something similar, but it will vary from system to system.
|
|
(If you can't figure it out, ask your system administrator.)
|
|
In the above example,
|
|
.Ar dist_directories
|
|
are the
|
|
distribution sets' directories, for the distribution sets you
|
|
wish to place on the tape. For instance, to put the
|
|
.Sy base No and Sy etc
|
|
distributions on tape (in order to do the absolute
|
|
minimum installation to a new disk), you would do the
|
|
following:
|
|
.D1 Ic cd .../NetBSD-\*V # the top of the tree
|
|
.D1 Ic cd x68k/binary/sets
|
|
.D1 Ic tar\ cf Ar tape_device Ic base.tgz\ etc.tgz
|
|
(Note that you still need to fill in
|
|
.Ar tape_device
|
|
in the example.)
|
|
.Pp
|
|
Once you have the files on the tape, you can proceed to the
|
|
next step in the installation or upgrade process. If you're
|
|
installing NetBSD from scratch, go to the section on preparing
|
|
your hard disk, below. If you're upgrading an existing
|
|
installation, go directly to the section on upgrading.
|
|
.It Em Install\ From\ Remote\ NFS\ Partition
|
|
.Pp
|
|
To install or upgrade NetBSD using a remote partition, mounted via
|
|
NFS, you must do the following:
|
|
.(Note
|
|
This method of installation is recommended only for
|
|
those already familiar with using BSD network
|
|
configuration and management commands. If you aren't,
|
|
this documentation should help, but is not intended to
|
|
be all-encompassing.
|
|
.Note)
|
|
.Pp
|
|
Place the NetBSD distribution sets you wish to install into a
|
|
directory on an NFS server, and make that directory mountable
|
|
by the machine on which you are installing or upgrading NetBSD.
|
|
This will probably require modifying the /etc/exports file on
|
|
of the NFS server and resetting its mount daemon (mountd).
|
|
(Both of these actions will probably require superuser
|
|
privileges on the server.)
|
|
.Pp
|
|
You need to know the numeric IP address of the NFS server,
|
|
and, if the server is not on a network directly connected to
|
|
the machine on which you're installing or upgrading NetBSD,
|
|
you need to know the numeric IP address of the router closest
|
|
to the NetBSD machine. Finally, you need to know the numeric
|
|
IP address of the NetBSD machine itself.
|
|
.Pp
|
|
Once the NFS server is set up properly and you have the
|
|
information mentioned above, you can proceed to the next step
|
|
in the installation or upgrade process. If you're installing
|
|
NetBSD from scratch, go to the section on preparing your hard
|
|
disk, below. If you're upgrading an existing installation, go
|
|
directly to the section on upgrading.
|
|
.Pp
|
|
.It Em Install\ via\ FTP
|
|
.Pp
|
|
To install or upgrade NetBSD by using FTP to get the installation
|
|
sets, you must do the following:
|
|
.(Note
|
|
This method of installation is recommended only for
|
|
those already familiar with using BSD network
|
|
configuration and management commands. If you aren't,
|
|
this documentation should help, but is not intended to
|
|
be all-encompassing.
|
|
.Note)
|
|
.Pp
|
|
The preparations for this installation/upgrade method are
|
|
easy; all you make sure that there's some FTP site from which
|
|
you can retrieve the NetBSD distribution when you're about to
|
|
install or upgrade. You need to know the numeric IP address
|
|
of that site, and, if it's not on a network directly connected
|
|
to the machine on which you're installing or upgrading NetBSD,
|
|
you need to know the numeric IP address of the router closest
|
|
to the NetBSD machine. Finally, you need to know the numeric
|
|
IP address of the NetBSD machine itself.
|
|
.Pp
|
|
Once you have this information, you can proceed to the next
|
|
step in the installation or upgrade process. If you're
|
|
installing NetBSD from scratch, go to the section on
|
|
preparing your hard disk, below. If you're upgrading an
|
|
existing installation, go directly to the section on
|
|
upgrading.
|
|
.El
|
|
.Pp
|
|
If you are upgrading NetBSD, you also have the option of installing
|
|
NetBSD by putting the new distribution sets somewhere in your existing
|
|
file system, and using them from there. To do that, you must do the
|
|
following:
|
|
.Bl -enum
|
|
.It
|
|
Place the distribution sets you wish to upgrade somewhere in
|
|
your current file system tree. At a bare minimum, you must
|
|
upgrade the "base" binary distribution, and so must put the
|
|
"base.tgz" set somewhere in your file system. If you wish,
|
|
you can do the other sets, as well, but you should NOT upgrade
|
|
the "etc" distribution; the "etc" distribution contains system
|
|
configuration files that you should review and update by hand.
|
|
.It
|
|
Once you have done this, you can proceed to the next step in
|
|
the upgrade process, actually upgrading your system.
|
|
.El
|