NetBSD/sys/dev/ic/cd1190reg.h

176 lines
6.1 KiB
C

/* $NetBSD: cd1190reg.h,v 1.5 2008/07/02 10:16:20 plunky Exp $ */
/*-
* Copyright (c) 1998 Iain Hibbert.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Definitions for Cirrus Logic CD1190 parallel chips.
*/
/* ACK Width Register */
#define CD1190_AWR 0x03
/* Controller Command Register */
#define CD1190_CCR 0x0b
#define CD1190_CCR_CGC (1<<7) /* Change Global Config Command */
#define CD1190_CCR_CGC_RESET (1<<0) /* CGC Reset Command */
#define CD1190_CCR_PAR (1<<6) /* Parallel Command */
#define CD1190_CCR_PAR_DISABLE (1<<2) /* PAR Parallel Disable */
#define CD1190_CCR_PAR_FLUSH (1<<1) /* PAR Flush FIFO */
#define CD1190_CCR_PAR_ENABLE (1<<0) /* PAR Parallel Enable */
#define CD1190_CCR_SIG (1<<5) /* Signal Command */
#define CD1190_CCR_SIG_SET_BUSY (1<<2) /* SIG Set Busy Output */
#define CD1190_CCR_SIG_ACK (1<<1) /* SIG Pulse ACK Output */
#define CD1190_CCR_SIG_CLR_BUSY (1<<0) /* SIG Clear Busy Output */
#define CD1190_CCR_TIM (1<<4) /* Timer Command */
#define CD1190_CCR_TIM_ENABLE (1<<3) /* Timer Enabled */
/* Data Time-0ut Register */
#define CD1190_DTR 0x09
/* End Of Service Request Register */
#define CD1190_ESR 0x10
/* FIFO Count Register */
#define CD1190_FCR 0x0e
/* FIFO Data Register */
#define CD1190_FDR 0x12
/* Firmware Revision Register */
#define CD1190_FRR 0x0f
/* FIFO Threshold Register */
#define CD1190_FTR 0x08
/* Global Config Register */
#define CD1190_GCR 0x0a
#define CD1190_GCR_NOACK (1<<2) /* NO-ACK handshaking */
#define CD1190_GCR_MODE (1<<1) /* Peripheral/Controller Mode */
#define CD1190_GCR_DIR (1<<0) /* Input/Output Direction */
/* defines for variable CD1190_IO */
#define CD1190_CO 0x00
#define CD1190_CI 0x01
#define CD1190_PO 0x02
#define CD1190_PI 0x03
/* Interrupt Config Register */
#define CD1190_ICR 0x01
#define CD1190_ICR_ENABLE (1<<7) /* Enable Interrupts */
#define CD1190_ICR_ACK (1<<3) /* Enable: Unsolicited ACK */
#define CD1190_ICR_FIFO (1<<2) /* Enable: FIFO Thresh/Time */
#define CD1190_ICR_SIGNAL (1<<1) /* Enable: Signal Status */
#define CD1190_ICR_TIMER (1<<0) /* Enable: Timer Expired */
/* Interrupt Status Register */
#define CD1190_ISR 0x0c
#define CD1190_ISR_INTERRUPT (1<<7) /* Interrupt Has Occurred */
#define CD1190_ISR_ACK (1<<3) /* Unsolicited ACK */
#define CD1190_ISR_FIFO (1<<2) /* FIFO Thresh/Time */
#define CD1190_ISR_SIGNAL (1<<1) /* Signal Status */
#define CD1190_ISR_TIMER (1<<0) /* Timer Expired */
/* Interrupt Vector Register */
#define CD1190_IVR 0x00
/* Parallel Status Register */
#define CD1190_PSR 0x1c
#define CD1190_PSR_ENP (1<<7) /* Parallel Enabled */
#define CD1190_PSR_BUSY (1<<6) /* Parallel Busy */
#define CD1190_PSR_ACK (1<<5) /* Parallel Acknowledge */
#define CD1190_PSR_STATUS (CD1190_PSR_ENP | CD1190_PSR_BUSY)
#define CD1190_PSR_NORMAL CD1190_PSR_ENP
/* Signal Control Register */
#define CD1190_SCR 0x1e
#define CD1190_SCR_WRRD (1<<7) /* Read Only: Write/Read */
#define CD1190_SCR_IP3 (1<<6) /* Read Only: Input Line 3 */
#define CD1190_SCR_IP2 (1<<5) /* Read Only: Input Line 2 */
#define CD1190_SCR_IP1 (1<<4) /* Read Only: Input Line 1 */
#define CD1190_SCR_WR_WRRD (1<<3) /* Write/Read */
#define CD1190_SCR_OP3 (1<<2) /* Output Line 3 */
#define CD1190_SCR_OP2 (1<<1) /* Output Line 2 */
#define CD1190_SCR_OP1 (1<<0) /* Output Line 1 */
/* Input signals
*
* IP3 - *ERROR
* IP2 - PAPER EMPTY / FAULT
* IP1 - SELECT
* WRRD - AFD
* OP3 - SLIN
* OP2 - *INIT / *RESET
* OP1 - N/A
*/
#define CD1190_SCR_NOERROR CD1190_SCR_IP3 /* Printer Error (active low) */
#define CD1190_SCR_PE CD1190_SCR_IP2 /* Paper Empty */
#define CD1190_SCR_SELECT CD1190_SCR_IP1 /* Printer Select */
#define CD1190_SCR_STATUS (CD1190_SCR_IP3 | CD1190_SCR_IP2 | CD1190_SCR_IP1)
/* Outout signals - Active High?
*
* IP3 - SLIN
* IP2 - *INIT / *RESET
* IP1 - N/A
* WRRD - AFD
* OP3 - *ERROR
* OP2 - SELECT
* OP1 - PAPER EMPTY / FAULT
*/
#define CD1190_SCR_RESET CD1190_SCR_OP2
#define CD1190_SCR_SEL_IN CD1190_SCR_OP3
/* Specification Register ZEROes */
#define CD1190_SR0 0x06
#define CD1190_SR0_WRRD (1<<7) /* WR/RD 1 to 0 Change */
#define CD1190_SR0_IP3 (1<<6) /* IP3 1 to 0 Change */
#define CD1190_SR0_IP2 (1<<5) /* IP2 1 to 0 Change */
#define CD1190_SR0_IP1 (1<<4) /* IP1 1 to 0 Change */
/* Specification Register ONEs */
#define CD1190_SR1 0x07
#define CD1190_SR1_WRRD (1<<7) /* WR/RD 0 to 1 Change */
#define CD1190_SR1_IP3 (1<<6) /* IP3 0 to 1 Change */
#define CD1190_SR1_IP2 (1<<5) /* IP2 0 to 1 Change */
#define CD1190_SR1_IP1 (1<<4) /* IP1 0 to 1 Change */
/* Signal Status Register */
#define CD1190_SSR 0x0d
#define CD1190_SSR_WRRD (1<<7) /* WR/RD Change */
#define CD1190_SSR_IP3 (1<<6) /* IP3 Change */
#define CD1190_SSR_IP2 (1<<5) /* IP2 Change */
#define CD1190_SSR_IP1 (1<<4) /* IP1 Change */
/* Strobe Width Register */
#define CD1190_SWR 0x02
/* Timer Multipler Register */
#define CD1190_TMR 0x05
/* Timer Prescale Register */
#define CD1190_TPR 0x04