147 lines
3.7 KiB
Plaintext
147 lines
3.7 KiB
Plaintext
.\" $NetBSD: hardware,v 1.6 2009/10/08 05:28:23 snj Exp $
|
|
.
|
|
.Nx*M
|
|
is a port of
|
|
.Nx
|
|
to PowerPC based evaluation boards.
|
|
At the present time, the following boards are supported:
|
|
.(bullet
|
|
Artesyn's PM/PPC board
|
|
.It
|
|
IBM PowerPC 405GP based Walnut
|
|
.It
|
|
Marvell PowerPC 750 based EV-64260
|
|
.It
|
|
NCD Explora451 NC
|
|
.It
|
|
Plat'Home OpenBlockS200
|
|
.It
|
|
Plat'Home OpenBlockS266 microserver
|
|
.bullet)
|
|
.Pp
|
|
However, this documentation is specific to installing
|
|
.Nx*M
|
|
on the Walnut board only.
|
|
.
|
|
.Ss2 Supported devices
|
|
.(bullet -offset indent
|
|
Ethernet:
|
|
The built-in Ethernet card is not supported, so another PCI
|
|
Ethernet card supported by
|
|
.Nx
|
|
must be provided if you want to use
|
|
.Nx*M
|
|
on a network.
|
|
Any PCI Ethernet card supported by
|
|
.Nx
|
|
should work.
|
|
.It
|
|
SCSI:
|
|
Any PCI SCSI card supported by
|
|
.Nx
|
|
should work, as should most SCSI disk/tape/CD-ROM devices.
|
|
.It
|
|
IDE:
|
|
.(bullet -compact
|
|
.\" XXXX
|
|
Promise Ultra66
|
|
.Pq Em pciide
|
|
.It
|
|
Other PCI IDE controllers should work, but there are no reports.
|
|
.It
|
|
Most IDE disk/CD-ROM/ATAPI devices should work.
|
|
.bullet)
|
|
.It
|
|
Audio
|
|
.(bullet -compact
|
|
PCI audio cards, although none have been tested.
|
|
.bullet)
|
|
.It
|
|
Serial ports
|
|
.(bullet -compact
|
|
On-board serial ports
|
|
.Pq Em com0
|
|
and
|
|
.Pq Em com1
|
|
.It
|
|
Some PCI serial ports should work, but no one has tried them
|
|
.bullet)
|
|
.It
|
|
PCI cards
|
|
.(bullet -compact
|
|
Most MI PCI cards should work, although very few have been tested with
|
|
.Nx*M
|
|
.Lk http://www.NetBSD.org/support/hardware/pci.html
|
|
.bullet)
|
|
.bullet)
|
|
.
|
|
.Ss2 Unsupported devices
|
|
.(bullet -offset indent
|
|
On-board Ethernet
|
|
.Pp
|
|
.Em Note :
|
|
This does not concern booting the kernel itself, since that
|
|
is done by the firmware.
|
|
For using an NFS root you will have to provide a supported network card,
|
|
though.
|
|
.bullet)
|
|
.
|
|
.Ss2 Supported boot devices and media
|
|
.
|
|
The firmware only supports booting from network or the serial port,
|
|
so you cannot boot from disk even if you install a disk controller.
|
|
Instructions for booting from serial port are not provided; in the
|
|
following we will describe how to setup netbooting.
|
|
.Pp
|
|
The first step is setting the IP addresses of both the walnut itself
|
|
and the host that will be serving the kernel image.
|
|
From the main menu, choose 3 to set the IP address of the machine:
|
|
.(disp
|
|
1 - Enable/disable tests
|
|
2 - Enable/disable boot devices
|
|
3 - Change IP addresses
|
|
4 - Ping test
|
|
5 - Toggle ROM monitor debugger
|
|
6 - Toggle automatic menu
|
|
7 - Display configuration
|
|
8 - Save changes to configuration
|
|
9 - Set baud rate for s1 boot
|
|
A - Enable/disable I cache (Enabled )
|
|
B - Enable/disable D cache (Enabled )
|
|
0 - Exit menu and continue
|
|
-\*[Gt] 3
|
|
.disp)
|
|
.Pp
|
|
Set the IP address for the local Ethernet with 1:
|
|
.(disp
|
|
--- CHANGE IP ADDRESS ---
|
|
Device List:
|
|
001 Enabled Ethernet [ENET]
|
|
local=0.0.0.0 remote=0.0.0.0 hwaddr=0004ace312bd
|
|
004 Disabled Serial Port 2 [S2]
|
|
local=8.1.1.2 remote=255.255.255.255 hwaddr=ffffffffffff
|
|
----------------------------
|
|
select device to change -\*[Gt]1
|
|
1 - Change local address
|
|
2 - Change remote address
|
|
0 - Return to main menu
|
|
-\*[Gt]1
|
|
Current IP address = (0.0.0.0)
|
|
Enter new IP address -\*[Gt]Enter IP address in dot notation, (eg. 8.1.1.2)
|
|
.disp)
|
|
.Pp
|
|
Here you enter the machine's IP address, e.g. 10.0.0.1.
|
|
Now you need to do the same thing to set the host IP address (choice 2
|
|
from the menu above).
|
|
.Pp
|
|
Once both the local and remote addresses are set, you can use
|
|
the ping test to make sure the ethernet is working; or you can
|
|
simply use option 0, "Exit menu and continue" to try to boot the
|
|
machine, if you already set up the remote machine to provide
|
|
a kernel image.
|
|
For details on how to do that, see the
|
|
.Sx Booting from the network
|
|
section below.
|
|
.Pp
|
|
You should now be able to boot the operating system.
|