NetBSD/usr.sbin/xntp/xntpd/refclock_pst.c

336 lines
8.6 KiB
C

/*
* refclock_pst - clock driver for PSTI/Traconex WWV/WWVH receivers
*/
#ifdef HAVE_CONFIG_H
#include <config.h>
#endif
#if defined(REFCLOCK) && defined(PST)
#include <stdio.h>
#include <ctype.h>
#include <sys/time.h>
#include "ntpd.h"
#include "ntp_io.h"
#include "ntp_refclock.h"
#include "ntp_stdlib.h"
/*
* This driver supports the PSTI 1010 and Traconex 1020 WWV/WWVH
* Receivers. No specific claim of accuracy is made for these receiver,
* but actual experience suggests that 10 ms would be a conservative
* assumption.
*
* The DIPswitches should be set for 9600 bps line speed, 24-hour day-
* of-year format and UTC time zone. Automatic correction for DST should
* be disabled. It is very important that the year be set correctly in
* the DIPswitches; otherwise, the day of year will be incorrect after
* 28 April of a normal or leap year. The propagation delay DIPswitches
* should be set according to the distance from the transmitter for both
* WWV and WWVH, as described in the instructions. While the delay can
* be set only to within 11 ms, the fudge time1 parameter can be used
* for vernier corrections.
*
* Using the poll sequence QTQDQM, the response timecode is in three
* sections totalling 50 ASCII printing characters, as concatenated by
* the driver, in the following format:
*
* ahh:mm:ss.fffs<cr> yy/dd/mm/ddd<cr> frdzycchhSSFTttttuuxx<cr>
*
* on-time = first <cr>
* hh:mm:ss.fff = hours, minutes, seconds, milliseconds
* a = AM/PM indicator (' ' for 24-hour mode)
* yy = year (from internal switches)
* dd/mm/ddd = day of month, month, day of year
* s = daylight-saving indicator (' ' for 24-hour mode)
* f = frequency enable (O = all frequencies enabled)
* r = baud rate (3 = 1200, 6 = 9600)
* d = features indicator (@ = month/day display enabled)
* z = time zone (0 = UTC)
* y = year (5 = 91)
* cc = WWV propagation delay (52 = 22 ms)
* hh = WWVH propagation delay (81 = 33 ms)
* SS = status (80 or 82 = operating correctly)
* F = current receive frequency (4 = 15 MHz)
* T = transmitter (C = WWV, H = WWVH)
* tttt = time since last update (0000 = minutes)
* uu = flush character (03 = ^c)
* xx = 94 (unknown)
*
* The alarm condition is indicated by other than '8' at A, which occurs
* during initial synchronization and when received signal is lost for
* an extended period; unlock condition is indicated by other than
* "0000" in the tttt subfield at Q.
*
* Fudge Factors
*
* There are no special fudge factors other than the generic.
*/
/*
* Interface definitions
*/
#define DEVICE "/dev/pst%d" /* device name and unit */
#define SPEED232 B9600 /* uart speed (9600 baud) */
#define PRECISION (-10) /* precision assumed (about 1 ms) */
#define WWVREFID "WWV\0" /* WWV reference ID */
#define WWVHREFID "WWVH" /* WWVH reference ID */
#define DESCRIPTION "PSTI/Traconex WWV/WWVH Receiver" /* WRU */
#define NSAMPLES 3 /* stages of median filter */
#define LENPST 46 /* min timecode length */
/*
* Imported from ntp_timer module
*/
extern u_long current_time; /* current time (s) */
/*
* Imported from ntpd module
*/
extern int debug; /* global debug flag */
/*
* Unit control structure
*/
struct pstunit {
int pollcnt; /* poll message counter */
u_char tcswitch; /* timecode switch */
char *lastptr; /* pointer to timecode data */
};
/*
* Function prototypes
*/
static int pst_start P((int, struct peer *));
static void pst_shutdown P((int, struct peer *));
static void pst_receive P((struct recvbuf *));
static void pst_poll P((int, struct peer *));
/*
* Transfer vector
*/
struct refclock refclock_pst = {
pst_start, /* start up driver */
pst_shutdown, /* shut down driver */
pst_poll, /* transmit poll message */
noentry, /* not used (old pst_control) */
noentry, /* initialize driver */
noentry, /* not used (old pst_buginfo) */
NOFLAGS /* not used */
};
/*
* pst_start - open the devices and initialize data for processing
*/
static int
pst_start(unit, peer)
int unit;
struct peer *peer;
{
register struct pstunit *up;
struct refclockproc *pp;
int fd;
char device[20];
/*
* Open serial port. Use CLK line discipline, if available.
*/
(void)sprintf(device, DEVICE, unit);
if (!(fd = refclock_open(device, SPEED232, LDISC_CLK)))
return (0);
/*
* Allocate and initialize unit structure
*/
if (!(up = (struct pstunit *)
emalloc(sizeof(struct pstunit)))) {
(void) close(fd);
return (0);
}
memset((char *)up, 0, sizeof(struct pstunit));
pp = peer->procptr;
pp->io.clock_recv = pst_receive;
pp->io.srcclock = (caddr_t)peer;
pp->io.datalen = 0;
pp->io.fd = fd;
if (!io_addclock(&pp->io)) {
(void) close(fd);
free(up);
return (0);
}
pp->unitptr = (caddr_t)up;
/*
* Initialize miscellaneous variables
*/
peer->precision = PRECISION;
pp->clockdesc = DESCRIPTION;
memcpy((char *)&pp->refid, WWVREFID, 4);
up->pollcnt = 2;
return (1);
}
/*
* pst_shutdown - shut down the clock
*/
static void
pst_shutdown(unit, peer)
int unit;
struct peer *peer;
{
register struct pstunit *up;
struct refclockproc *pp;
pp = peer->procptr;
up = (struct pstunit *)pp->unitptr;
io_closeclock(&pp->io);
free(up);
}
/*
* pst_receive - receive data from the serial interface
*/
static void
pst_receive(rbufp)
struct recvbuf *rbufp;
{
register struct pstunit *up;
struct refclockproc *pp;
struct peer *peer;
l_fp trtmp;
u_long ltemp;
char ampmchar; /* AM/PM indicator */
char daychar; /* standard/daylight indicator */
char junque[10]; /* "yy/dd/mm/" discard */
char info[14]; /* "frdzycchhSSFT" clock info */
/*
* Initialize pointers and read the timecode and timestamp
*/
peer = (struct peer *)rbufp->recv_srcclock;
pp = peer->procptr;
up = (struct pstunit *)pp->unitptr;
up->lastptr += refclock_gtlin(rbufp, up->lastptr, pp->lastcode
+ BMAX - 2 - up->lastptr, &trtmp);
*up->lastptr++ = ' ';
*up->lastptr = '\0';
/*
* Note we get a buffer and timestamp for each <cr>, but only
* the first timestamp is retained.
*/
if (!up->tcswitch)
pp->lastrec = trtmp;
up->tcswitch++;
pp->lencode = up->lastptr - pp->lastcode;
if (up->tcswitch < 3)
return;
up->pollcnt = 2;
record_clock_stats(&peer->srcadr, pp->lastcode);
#ifdef DEBUG
if (debug)
printf("pst: timecode %d %s\n", pp->lencode,
pp->lastcode);
#endif
/*
* We get down to business, check the timecode format and decode
* its contents. If the timecode has invalid length or is not in
* proper format, we declare bad format and exit.
*/
if (pp->lencode < LENPST) {
refclock_report(peer, CEVNT_BADREPLY);
return;
}
/*
* Timecode format:
* "ahh:mm:ss.fffs yy/dd/mm/ddd frdzycchhSSFTttttuuxx"
*/
if (sscanf(pp->lastcode, "%c%2d:%2d:%2d.%3d%c %9s%3d%13s%4ld",
&ampmchar, &pp->hour, &pp->minute, &pp->second,
&pp->msec, &daychar, junque, &pp->day,
info, &ltemp) != 10) {
refclock_report(peer, CEVNT_BADREPLY);
return;
}
/*
* Decode synchronization, quality and last update. If
* unsynchronized, set the leap bits accordingly and exit. Once
* synchronized, the dispersion depends only on when the clock
* was last heard, which depends on the time since last update,
* as reported by the clock.
*/
if (info[9] != '8') {
pp->leap = LEAP_NOTINSYNC;
} else {
pp->leap = 0;
pp->lasttime = current_time - ltemp;
if (info[12] == 'H')
memcpy((char *)&pp->refid, WWVHREFID, 4);
else
memcpy((char *)&pp->refid, WWVREFID, 4);
if (peer->stratum <= 1)
peer->refid = pp->refid;
}
/*
* Process the new sample in the median filter and determine the
* reference clock offset and dispersion. We use lastrec as both
* the reference time and receive time in order to avoid being
* cute, like setting the reference time later than the receive
* time, which may cause a paranoid protocol module to chuck out
* the data.
*/
if (!refclock_process(pp, NSAMPLES, NSAMPLES)) {
refclock_report(peer, CEVNT_BADTIME);
return;
}
trtmp = pp->lastrec;
trtmp.l_ui -= ltemp;
refclock_receive(peer, &pp->offset, 0, pp->dispersion, &trtmp,
&pp->lastrec, pp->leap);
}
/*
* pst_poll - called by the transmit procedure
*/
static void
pst_poll(unit, peer)
int unit;
struct peer *peer;
{
register struct pstunit *up;
struct refclockproc *pp;
/*
* Time to poll the clock. The PSTI/Traconex clock responds to a
* "QTQDQMT" by returning a timecode in the format specified
* above. If nothing is heard from the clock for two polls,
* declare a timeout and keep going.
*/
pp = peer->procptr;
up = (struct pstunit *)pp->unitptr;
if (up->pollcnt == 0)
refclock_report(peer, CEVNT_TIMEOUT);
else
up->pollcnt--;
up->tcswitch = 0;
up->lastptr = pp->lastcode;
if (write(pp->io.fd, "QTQDQMT", 6) != 6) {
refclock_report(peer, CEVNT_FAULT);
} else
pp->polls++;
}
#endif