183 lines
8.6 KiB
C
183 lines
8.6 KiB
C
/* $NetBSD: makphyreg.h,v 1.11 2020/08/03 07:25:59 msaitoh Exp $ */
|
|
|
|
/*-
|
|
* Copyright (c) 2001 The NetBSD Foundation, Inc.
|
|
* All rights reserved.
|
|
*
|
|
* This code is derived from software contributed to The NetBSD Foundation
|
|
* by Jason R. Thorpe.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
|
|
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
|
|
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
|
|
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#ifndef _DEV_MII_MAKPHYREG_H_
|
|
#define _DEV_MII_MAKPHYREG_H_
|
|
|
|
/*
|
|
* Marvell 88E1000 ``Alaska'' 10/100/1000 PHY registers.
|
|
*/
|
|
|
|
#define MAKPHY_PSCR 0x10 /* PHY specific control register */
|
|
#define PSCR_DIS_JABBER (1U << 0) /* disable jabber */
|
|
#define PSCR_POL_REV (1U << 1) /* polarity reversal */
|
|
#define PSCR_SQE_TEST (1U << 2) /* SQE test */
|
|
#define PSCR_MBO (1U << 3) /* must be one */
|
|
#define PSCR_DIS_125CLK (1U << 4) /* 125CLK low */
|
|
#define PSCR_MDI_XOVER_MODE(x) ((x) << 5) /* crossover mode */
|
|
#define PSCR_LOW_10T_THRESH (1U << 7) /* lower 10BASE-T Rx threshold */
|
|
#define PSCR_EN_DETECT(x) ((x) << 8) /* Energy Detect */
|
|
#define PSCR_FORCE_LINK_GOOD (1U << 10) /* force link good */
|
|
#define PSCR_CRS_ON_TX (1U << 11) /* assert CRS on transmit */
|
|
#define PSCR_RX_FIFO(x) ((x) << 12) /* Rx FIFO depth */
|
|
#define PSCR_TX_FIFO(x) ((x) << 14) /* Tx FIFO depth */
|
|
|
|
#define XOVER_MODE_MDI 0
|
|
#define XOVER_MODE_MDIX 1
|
|
#define XOVER_MODE_AUTO 2
|
|
|
|
/* 88E3016 */
|
|
/* bit 2 and 3 are reserved */
|
|
#define E3016_PSCR_MDI_XOVER_MODE(x) ((x) << 4) /* crossover mode */
|
|
#define E3016_PSCR_SIGDET_POLARITY (1U << 6) /* 0: Active H, 1: Active L */
|
|
#define E3016_PSCR_EXTDIST (1U << 7) /* Enable Extended Distance */
|
|
#define E3016_PSCR_FEFI_DIS (1U << 8) /* Disable FEFI */
|
|
#define E3016_PSCR_SCRAMBLE_DIS (1U << 9) /* Disable Scrambler */
|
|
/* bit 10 is reserved */
|
|
#define E3016_PSCR_NLPGEN_DIS (1U << 11) /* Disable Linkpulse Generation */
|
|
#define E3016_PSCR_REG8NXTPG (1U << 12) /* En. Link Partner Next Page R */
|
|
#define E3016_PSCR_NLPCHK_DIS (1U << 13) /* Disable NLP check */
|
|
#define E3016_PSCR_EN_DETECT (1U << 14) /* Energy Detect */
|
|
/* bit 15 is reserved */
|
|
|
|
/* 88E1112 page 1 */
|
|
#define MAKPHY_FSCR 0x10 /* Fiber specific control register */
|
|
#define FSCR_XMITTER_DIS 0x0008 /* Transmitter Disable */
|
|
|
|
/* 88E1112 page 2 */
|
|
#define MAKPHY_MSCR 0x10 /* MAC specific control register */
|
|
#define MSCR_TX_FIFODEPTH 0xc000 /* Transmi FIFO Depth */
|
|
#define MSCR_RX_FIFODEPTH 0x3000 /* Receive FIFO Depth */
|
|
#define MSCR_AUTOPREF_MASK 0x0c00 /* Autoselect preferred media mask */
|
|
#define MSCR_AUTOPREF_NO 0x0000 /* No preference */
|
|
#define MSCR_AUTOPREF_FIBER 0x0400 /* Preferred Fiber */
|
|
#define MSCR_AUTOPREF_COPPER 0x0800 /* Preferred Copper */
|
|
#define MSCR_MODE_MASK 0x0380 /* Mode select mask */
|
|
#define MSCR_M_100FX 0x0000 /* 100BASE-FX */
|
|
#define MSCR_M_COOPER_GBIC 0x0080 /* Copper GBIC */
|
|
#define MSCR_M_AUTO_COPPER_SGMII 0x0100 /* Auto Copper/SGMII */
|
|
#define MSCR_M_AUTO_COPPER_1000X 0x0180 /* Auto Copper/1000BASE-X */
|
|
#define MSCR_M_COPPER 0x0280 /* Copper only */
|
|
#define MSCR_M_SGMII 0x0300 /* SGMII only */
|
|
#define MSCR_M_1000X 0x0380 /* 1000BASE-X only */
|
|
#define MSCR_SGMII_PDOWN 0x0008 /* SGMII MAC Interface Power Down */
|
|
#define MSCR_ENHANCED_SGMII 0x0004 /* Enhanced SGMII */
|
|
|
|
#define MAKPHY_PSSR 0x11 /* PHY specific status register */
|
|
#define MAKPHY_PSSR_JABBER (1U << 0) /* jabber indication */
|
|
#define MAKPHY_PSSR_POLARITY (1U << 1) /* polarity indiciation */
|
|
#define MAKPHY_PSSR_MDIX (1U << 6) /* 1 = MIDX, 0 = MDI */
|
|
#define MAKPHY_PSSR_CABLE_LENGTH_get(x) (((x) >> 7) & 0x3)
|
|
#define MAKPHY_PSSR_LINK (1U << 10) /* link indication */
|
|
#define MAKPHY_PSSR_RESOLVED (1U << 11) /* speed and duplex resolved */
|
|
#define MAKPHY_PSSR_PAGE_RECEIVED (1U << 12) /* page received */
|
|
#define MAKPHY_PSSR_DUPLEX (1U << 13) /* 1 = FDX */
|
|
#define MAKPHY_PSSR_SPEED_get(x) (((x) >> 14) & 0x3)
|
|
|
|
#define SPEED_10 0
|
|
#define SPEED_100 1
|
|
#define SPEED_1000 2
|
|
#define SPEED_reserved 3
|
|
|
|
/* For 88E1112 */
|
|
#define MAKPHY_PSSR_RESOLUTION_FIBER (1U << 7) /*
|
|
* Fiber/Copper resolution
|
|
* 1 = Fiber, 0 = Copper
|
|
*/
|
|
|
|
#define MAKPHY_IE 0x12 /* Interrupt enable */
|
|
#define IE_JABBER (1U << 0) /* jabber indication */
|
|
#define IE_POL_CHANGED (1U << 1) /* polarity changed */
|
|
#define IE_MDI_XOVER_CHANGED (1U << 6) /* MDI/MDIX changed */
|
|
#define IE_FIFO_OVER_UNDER (1U << 7) /* FIFO over/underflow */
|
|
#define IE_FALSE_CARRIER (1U << 8) /* false carrier detected */
|
|
#define IE_SYMBOL_ERROR (1U << 9) /* symbol error occurred */
|
|
#define IE_LINK_CHANGED (1U << 10) /* link status changed */
|
|
#define IE_ANEG_COMPLETE (1U << 11) /* autonegotiation completed */
|
|
#define IE_PAGE_RECEIVED (1U << 12) /* page received */
|
|
#define IE_DUPLEX_CHANGED (1U << 13) /* duplex changed */
|
|
#define IE_SPEED_CHANGED (1U << 14) /* speed changed */
|
|
#define IE_ANEG_ERROR (1U << 15) /* autonegotiation error occurred */
|
|
|
|
#define MAKPHY_IS 0x13 /* Interrupt status */
|
|
/* See Interrupt enable bits */
|
|
|
|
#define MAKPHY_EPSC 0x14 /* extended PHY specific control */
|
|
#define EPSC_TX_CLK(x) ((x) << 4) /* transmit clock */
|
|
#define EPSC_TBI_RCLK_DIS (1U << 12) /* TBI RCLK disable */
|
|
#define EPSC_TBI_RX_CLK125_EN (1U << 13) /* TBI RX_CLK125 enable */
|
|
#define EPSC_LINK_DOWN_NO_IDLES (1U << 15) /* 1 = lost lock detect */
|
|
|
|
#define MAKPHY_REC 0x15 /* receive error counter */
|
|
|
|
#define MAKPHY_EADR 0x16 /* extended address register */
|
|
|
|
#define MAKPHY_LEDCTRL 0x18 /* LED control */
|
|
#define LEDCTRL_LED_TX (1U << 0) /* 1 = activ/link, 0 = xmit */
|
|
#define LEDCTRL_LED_RX (1U << 1) /* 1 = activ/link, 1 = recv */
|
|
#define LEDCTRL_LED_DUPLEX (1U << 2) /* 1 = duplex, 0 = dup/coll */
|
|
#define LEDCTRL_LED_LINK (1U << 3) /* 1 = spd/link, 0 = link */
|
|
#define LEDCTRL_BLINK_RATE(x) ((x) << 8)
|
|
#define LEDCTRL_PULSE_STRCH(x) ((x) << 12)
|
|
#define LEDCTRL_DISABLE (1U << 15) /* disable LED */
|
|
|
|
/* For 88E1011, 88E1111 */
|
|
#define MAKPHY_ESSR 0x1b /* Extended PHY specific status */
|
|
#define ESSR_AUTOSEL_DISABLE 0x8000 /* Fiber/Copper autoselect disable */
|
|
#define ESSR_FIBER_LINK 0x2000 /* Fiber/Copper resolution */
|
|
#define ESSR_SER_ANEG_BYPASS 0x1000 /* Serial Iface Aneg bypass enable */
|
|
#define ESSR_SER_ANEG_BYPASS_ST 0x0800 /* Serial Iface Aneg bypass status */
|
|
#define ESSR_INTR_POLARITY 0x0400 /* Interrupt Polarity */
|
|
#define ESSR_AUTO_MEDIAREG_SEL 0x0200 /* Auto Medium Register Selection */
|
|
#define ESSR_DTE_DROP_HYST 0x01e0 /* DTE detect status drop hysteresis */
|
|
#define ESSR_DTE_POWER 0x0010
|
|
#define ESSR_HWCFG_MODE 0x000f
|
|
#define ESSR_SGMII_WC_COPPER 0x0000 /* SGMII w/ Clock w/ SGMII AN Copper */
|
|
#define ESSR_RTBI_FIBER 0x0001 /* RTBI to Fiber */
|
|
#define ESSR_RGMII_FIBER 0x0003 /* RGMII to Fiber */
|
|
#define ESSR_SGMII_WOC_COPPER 0x0004 /* SGMII w/o Clock w/ SGMII AN Copp. */
|
|
#define ESSR_TBI_FIBER 0x0005 /* TBI to Fiber */
|
|
#define ESSR_RGMII_SGMII 0x0006 /* RGMII to SGMII */
|
|
#define ESSR_GMII_FIBER 0x0007 /* GMII to Fiber */
|
|
#define ESSR_SERIAL_WAN 0x0008 /* 88E1011: Serial w 1000KX AN */
|
|
#define ESSR_GBIC 0x0008 /* 88E1111: GBIC */
|
|
#define ESSR_RTBI_COPPER 0x0009 /* RTBI to Copper */
|
|
#define ESSR_RGMII_COPPER 0x000b /* RGMII to Copper */
|
|
#define ESSR_RGMII_AUTOSEL 0x000b /* RGMII with Auto-Selection */
|
|
#define ESSR_SERIAL_WOAN 0x000c /* 88E1011: Serial w/o 1000KX AN */
|
|
#define ESSR_1000X_WOAN 0x000c /* 88E1111: 1000X w/o AN Copper */
|
|
#define ESSR_TBI_COPPER 0x000d /* TBI to Copper */
|
|
#define ESSR_GMII_SGMII 0x000e /* GMII to SGMII */
|
|
#define ESSR_GMII_COPPER 0x000f /* GMII to Copper */
|
|
#define ESSR_GMII_AUTOSEL 0x000f /* GMII with Auto-Selection */
|
|
|
|
#endif /* _DEV_MII_MAKPHYREG_H_ */
|