84 lines
3.2 KiB
Plaintext
84 lines
3.2 KiB
Plaintext
$NetBSD: README.VMEbus-RAM,v 1.3 2001/06/19 12:59:15 wiz Exp $
|
|
|
|
NetBSD/mvme68k port: VMEbus RAM card configuration
|
|
|
|
As of version 1.3, NetBSD-mvme68k (for VME147) officially supports
|
|
additional RAM in A32 space over the VMEbus.
|
|
|
|
This file describes where to configure your VMEbus RAM and how to
|
|
point the kernel in the direction of it.
|
|
|
|
The MVME147 board has a fairly primitive VMEbus controller chip. The
|
|
mapping of cpu address to VMEbus address is hardwired and so dictates
|
|
what can be seen where by the 68030.
|
|
|
|
From the cpu's perspective, A24 space spans 0x00000000 to 0x00ffffff.
|
|
However, onboard RAM also spans this space. With 8Mb of onboard RAM,
|
|
only the top 8Mb of VMEbus A24 space can be seen. With 16Mb onboard,
|
|
there is no easy way to get at A24 space at all!
|
|
|
|
The cpu sees VMEbus A32 space starting from 0x01000000. The lowest
|
|
16Mb of A32 space is not accessible (it's covered either by onboard
|
|
RAM or A24 space). With 32Mb of onboard RAM, the cpu can address A32
|
|
space from 0x02000000 upwards. This still leaves a considerable chunk
|
|
of A32 space visible, so in practice isn't really a problem.
|
|
|
|
The best place for VMEbus RAM cards is in A32 space, at the address
|
|
given by:
|
|
|
|
max(0x01000000, onboard_ram_size)
|
|
|
|
In my case, this would locate my 8Mb VMEbus RAM card at 0x01000000.
|
|
|
|
This starting address needs to be written to the MVME147's NVRAM at
|
|
address 0xfffe0764, as follows:
|
|
|
|
147Bug> mm fffe0764 ;L
|
|
FFFE0764 00000000? 01000000 <cr> <--- you type 01000000
|
|
FFFE0768 00000000? . <cr>
|
|
147Bug>
|
|
|
|
Next, you need to configure the end address of VMEbus RAM. Assuming
|
|
your RAM card is 8Mb in size, this would be 0x017fffff. You need to
|
|
write this value to NVRAM address 0xfffe0768, as follows:
|
|
|
|
147Bug> mm fffe0768 ;L
|
|
FFFE0768 00000000? 017fffff <cr> <--- you type 017fffff
|
|
FFFE076c 00000000? . <cr>
|
|
147Bug>
|
|
|
|
You could obviously combine the above two steps.
|
|
|
|
If you have more than one VMEbus RAM card, you must configure them so
|
|
that they appear physically contiguous in A32 address space. So, to add
|
|
another 8Mb card in addition to the card above, it should be jumpered
|
|
to start at 0x01800000. In this case, you would change NVRAM location
|
|
0xfffe0768 to be 0x01ffffff.
|
|
|
|
If NVRAM location 0xfffe0764 is zero, the kernel assumes you only have
|
|
onboard RAM and will not attempt to use any VMEbus RAM.
|
|
|
|
|
|
Some extra notes on VMEbus RAM cards
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
So... You've got your nice shiny VMEbus RAM card up and running with
|
|
NetBSD, and you're wondering why your system runs slower than it did
|
|
with less RAM!
|
|
|
|
The simple answer is "Motorola got it wrong". (Or at least that's my
|
|
opinion. If anyone can cure the following, let me know!)
|
|
|
|
In their infinite wisdom, the designers of the MVME147 decided that
|
|
they would disable the 68030's cache on *any* access to the VMEbus.
|
|
The upshot is that the cache only works for onboard RAM, not VMEbus
|
|
RAM, hence your system runs slower. As far as I can see, the only
|
|
way to cure this is to physically cut a trace on the circuit board
|
|
and use the MMU to control caching on a page-by-page basis...
|
|
|
|
Anyhow, hopefully the above instructions have finally put to rest
|
|
the most asked question about the mvme68k port.
|
|
|
|
Cheers,
|
|
Steve Woodford: scw@netbsd.org
|