413 lines
10 KiB
C
413 lines
10 KiB
C
/* $NetBSD: if_ate.c,v 1.50 2008/04/12 06:27:01 tsutsui Exp $ */
|
|
|
|
/*
|
|
* All Rights Reserved, Copyright (C) Fujitsu Limited 1995
|
|
*
|
|
* This software may be used, modified, copied, distributed, and sold, in
|
|
* both source and binary form provided that the above copyright, these
|
|
* terms and the following disclaimer are retained. The name of the author
|
|
* and/or the contributor may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION.
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
/*
|
|
* Portions copyright (C) 1993, David Greenman. This software may be used,
|
|
* modified, copied, distributed, and sold, in both source and binary form
|
|
* provided that the above copyright and these terms are retained. Under no
|
|
* circumstances is the author responsible for the proper functioning of this
|
|
* software, nor does the author assume any responsibility for damages
|
|
* incurred with its use.
|
|
*/
|
|
|
|
#include <sys/cdefs.h>
|
|
__KERNEL_RCSID(0, "$NetBSD: if_ate.c,v 1.50 2008/04/12 06:27:01 tsutsui Exp $");
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/device.h>
|
|
#include <sys/socket.h>
|
|
#include <sys/syslog.h>
|
|
|
|
#include <net/if.h>
|
|
#include <net/if_ether.h>
|
|
#include <net/if_media.h>
|
|
|
|
#include <sys/bus.h>
|
|
#include <sys/intr.h>
|
|
|
|
#include <dev/ic/mb86960reg.h>
|
|
#include <dev/ic/mb86960var.h>
|
|
|
|
#include <dev/isa/isavar.h>
|
|
|
|
int ate_match(device_t, cfdata_t, void *);
|
|
void ate_attach(device_t, device_t, void *);
|
|
|
|
struct ate_softc {
|
|
struct mb86960_softc sc_mb86960; /* real "mb86960" softc */
|
|
|
|
/* ISA-specific goo. */
|
|
void *sc_ih; /* interrupt cookie */
|
|
};
|
|
|
|
CFATTACH_DECL_NEW(ate_isa, sizeof(struct ate_softc),
|
|
ate_match, ate_attach, NULL, NULL);
|
|
|
|
struct fe_simple_probe_struct {
|
|
uint8_t port; /* Offset from the base I/O address. */
|
|
uint8_t mask; /* Bits to be checked. */
|
|
uint8_t bits; /* Values to be compared against. */
|
|
};
|
|
|
|
static inline int fe_simple_probe(bus_space_tag_t, bus_space_handle_t,
|
|
struct fe_simple_probe_struct const *);
|
|
static int ate_find(bus_space_tag_t, bus_space_handle_t, int *, int *);
|
|
static int ate_detect(bus_space_tag_t, bus_space_handle_t,
|
|
uint8_t enaddr[ETHER_ADDR_LEN]);
|
|
|
|
static int const ate_iomap[8] = {
|
|
0x260, 0x280, 0x2A0, 0x240, 0x340, 0x320, 0x380, 0x300
|
|
};
|
|
#define NATE_IOMAP (sizeof (ate_iomap) / sizeof (ate_iomap[0]))
|
|
#define ATE_NPORTS 0x20
|
|
|
|
#ifdef ATE_DEBUG
|
|
#define DPRINTF printf
|
|
#else
|
|
#define DPRINTF while (/*CONSTCOND*/0) printf
|
|
#endif
|
|
|
|
/*
|
|
* Hardware probe routines.
|
|
*/
|
|
|
|
/*
|
|
* Determine if the device is present.
|
|
*/
|
|
int
|
|
ate_match(device_t parent, cfdata_t cf, void *aux)
|
|
{
|
|
struct isa_attach_args *ia = aux;
|
|
bus_space_tag_t iot = ia->ia_iot;
|
|
bus_space_handle_t ioh;
|
|
int i, iobase, irq, rv = 0;
|
|
uint8_t myea[ETHER_ADDR_LEN];
|
|
|
|
if (ia->ia_nio < 1)
|
|
return 0;
|
|
if (ia->ia_nirq < 1)
|
|
return 0;
|
|
|
|
if (ISA_DIRECT_CONFIG(ia))
|
|
return 0;
|
|
|
|
/* Disallow wildcarded values. */
|
|
if (ia->ia_io[0].ir_addr == ISA_UNKNOWN_PORT)
|
|
return 0;
|
|
|
|
/*
|
|
* See if the sepcified address is valid for MB86965A JLI mode.
|
|
*/
|
|
for (i = 0; i < NATE_IOMAP; i++)
|
|
if (ate_iomap[i] == ia->ia_io[0].ir_addr)
|
|
break;
|
|
if (i == NATE_IOMAP) {
|
|
DPRINTF("%s: unknown iobase 0x%x\n",
|
|
__func__, ia->ia_io[0].ir_addr);
|
|
return 0;
|
|
}
|
|
|
|
/* Map i/o space. */
|
|
if (bus_space_map(iot, ia->ia_io[0].ir_addr, ATE_NPORTS, 0, &ioh)) {
|
|
DPRINTF("ate_match: couldn't map iospace 0x%x\n",
|
|
ia->ia_io[0].ir_addr);
|
|
return 0;
|
|
}
|
|
|
|
if (ate_find(iot, ioh, &iobase, &irq) == 0) {
|
|
DPRINTF("%s: ate_find failed\n", __func__);
|
|
goto out;
|
|
}
|
|
|
|
if (iobase != ia->ia_io[0].ir_addr) {
|
|
DPRINTF("%s: unexpected iobase in board: 0x%x\n",
|
|
__func__, iobase);
|
|
goto out;
|
|
}
|
|
|
|
if (ate_detect(iot, ioh, myea) == 0) { /* XXX necessary? */
|
|
DPRINTF("%s: ate_detect failed\n", __func__);
|
|
goto out;
|
|
}
|
|
|
|
if (ia->ia_irq[0].ir_irq != ISA_UNKNOWN_IRQ) {
|
|
if (ia->ia_irq[0].ir_irq != irq) {
|
|
aprint_error("%s: irq mismatch; "
|
|
"kernel configured %d != board configured %d\n",
|
|
__func__, ia->ia_irq[0].ir_irq, irq);
|
|
goto out;
|
|
}
|
|
} else
|
|
ia->ia_irq[0].ir_irq = irq;
|
|
|
|
ia->ia_nio = 1;
|
|
ia->ia_io[0].ir_size = ATE_NPORTS;
|
|
|
|
ia->ia_nirq = 1;
|
|
|
|
ia->ia_niomem = 0;
|
|
ia->ia_ndrq = 0;
|
|
|
|
rv = 1;
|
|
|
|
out:
|
|
bus_space_unmap(iot, ioh, ATE_NPORTS);
|
|
return rv;
|
|
}
|
|
|
|
/*
|
|
* Check for specific bits in specific registers have specific values.
|
|
*/
|
|
static inline int
|
|
fe_simple_probe(bus_space_tag_t iot, bus_space_handle_t ioh,
|
|
struct fe_simple_probe_struct const *sp)
|
|
{
|
|
uint8_t val;
|
|
struct fe_simple_probe_struct const *p;
|
|
|
|
for (p = sp; p->mask != 0; p++) {
|
|
val = bus_space_read_1(iot, ioh, p->port);
|
|
if ((val & p->mask) != p->bits) {
|
|
DPRINTF("%s: %x & %x != %x\n",
|
|
__func__, val, p->mask, p->bits);
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
/*
|
|
* Hardware (vendor) specific probe routines.
|
|
*/
|
|
|
|
/*
|
|
* Probe and initialization for Allied-Telesis AT1700/RE2000 series.
|
|
*/
|
|
static int
|
|
ate_find(bus_space_tag_t iot, bus_space_handle_t ioh, int *iobase, int *irq)
|
|
{
|
|
uint8_t eeprom[FE_EEPROM_SIZE];
|
|
int n;
|
|
|
|
static const int irqmap[4][4] = {
|
|
{ 3, 4, 5, 9 },
|
|
{ 10, 11, 12, 15 },
|
|
{ 3, 11, 5, 15 },
|
|
{ 10, 11, 14, 15 },
|
|
};
|
|
static const struct fe_simple_probe_struct probe_table[] = {
|
|
{ FE_DLCR2, 0x70, 0x00 },
|
|
{ FE_DLCR4, 0x08, 0x00 },
|
|
{ FE_DLCR5, 0x80, 0x00 },
|
|
#if 0
|
|
{ FE_BMPR16, 0x1B, 0x00 },
|
|
{ FE_BMPR17, 0x7F, 0x00 },
|
|
#endif
|
|
{ 0, 0x00, 0x00 },
|
|
};
|
|
|
|
#if ATE_DEBUG >= 4
|
|
log(LOG_INFO, "%s: probe (0x%x) for ATE\n", __func__, iobase);
|
|
#if 0
|
|
fe_dump(LOG_INFO, sc);
|
|
#endif
|
|
#endif
|
|
|
|
/*
|
|
* We should test if MB86965A is on the base address now.
|
|
* Unfortunately, it is very hard to probe it reliably, since
|
|
* we have no way to reset the chip under software control.
|
|
* On cold boot, we could check the "signature" bit patterns
|
|
* described in the Fujitsu document. On warm boot, however,
|
|
* we can predict almost nothing about register values.
|
|
*/
|
|
if (fe_simple_probe(iot, ioh, probe_table) == 0)
|
|
return 0;
|
|
|
|
/* Check if our I/O address matches config info on 86965. */
|
|
n = (bus_space_read_1(iot, ioh, FE_BMPR19) & FE_B19_ADDR)
|
|
>> FE_B19_ADDR_SHIFT;
|
|
*iobase = ate_iomap[n];
|
|
|
|
/*
|
|
* We are now almost sure we have an AT1700 at the given
|
|
* address. So, read EEPROM through 86965. We have to write
|
|
* into LSI registers to read from EEPROM. I want to avoid it
|
|
* at this stage, but I cannot test the presence of the chip
|
|
* any further without reading EEPROM. FIXME.
|
|
*/
|
|
mb86965_read_eeprom(iot, ioh, eeprom);
|
|
|
|
/* Make sure that config info in EEPROM and 86965 agree. */
|
|
if (eeprom[FE_EEPROM_CONF] != bus_space_read_1(iot, ioh, FE_BMPR19)) {
|
|
#ifdef DIAGNOSTIC
|
|
printf("%s: incorrect configuration in eeprom and chip\n",
|
|
__func__);
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Try to determine IRQ settings.
|
|
* Different models use different ranges of IRQs.
|
|
*/
|
|
n = (bus_space_read_1(iot, ioh, FE_BMPR19) & FE_B19_IRQ)
|
|
>> FE_B19_IRQ_SHIFT;
|
|
switch (eeprom[FE_ATI_EEP_REVISION] & 0xf0) {
|
|
case 0x30:
|
|
*irq = irqmap[3][n];
|
|
break;
|
|
case 0x10:
|
|
case 0x50:
|
|
*irq = irqmap[2][n];
|
|
break;
|
|
case 0x40:
|
|
case 0x60:
|
|
if (eeprom[FE_ATI_EEP_MAGIC] & 0x04) {
|
|
*irq = irqmap[1][n];
|
|
break;
|
|
}
|
|
default:
|
|
*irq = irqmap[0][n];
|
|
break;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
/*
|
|
* Determine type and ethernet address.
|
|
*/
|
|
static int
|
|
ate_detect(bus_space_tag_t iot, bus_space_handle_t ioh,
|
|
uint8_t enaddr[ETHER_ADDR_LEN])
|
|
{
|
|
uint8_t eeprom[FE_EEPROM_SIZE];
|
|
int type;
|
|
|
|
/* Get our station address from EEPROM. */
|
|
mb86965_read_eeprom(iot, ioh, eeprom);
|
|
memcpy(enaddr, eeprom + FE_ATI_EEP_ADDR, ETHER_ADDR_LEN);
|
|
|
|
/* Make sure we got a valid station address. */
|
|
if ((enaddr[0] & 0x03) != 0x00 ||
|
|
(enaddr[0] == 0x00 && enaddr[1] == 0x00 && enaddr[2] == 0x00)) {
|
|
DPRINTF("%s: invalid ethernet address\n", __func__);
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Determine the card type.
|
|
*/
|
|
switch (eeprom[FE_ATI_EEP_MODEL]) {
|
|
case FE_ATI_MODEL_AT1700T:
|
|
type = FE_TYPE_AT1700T;
|
|
break;
|
|
case FE_ATI_MODEL_AT1700BT:
|
|
type = FE_TYPE_AT1700BT;
|
|
break;
|
|
case FE_ATI_MODEL_AT1700FT:
|
|
type = FE_TYPE_AT1700FT;
|
|
break;
|
|
case FE_ATI_MODEL_AT1700AT:
|
|
type = FE_TYPE_AT1700AT;
|
|
break;
|
|
default:
|
|
type = FE_TYPE_AT_UNKNOWN;
|
|
break;
|
|
}
|
|
|
|
return type;
|
|
}
|
|
|
|
void
|
|
ate_attach(device_t parent, device_t self, void *aux)
|
|
{
|
|
struct ate_softc *isc = device_private(self);
|
|
struct mb86960_softc *sc = &isc->sc_mb86960;
|
|
struct isa_attach_args *ia = aux;
|
|
bus_space_tag_t iot = ia->ia_iot;
|
|
bus_space_handle_t ioh;
|
|
uint8_t myea[ETHER_ADDR_LEN];
|
|
const char *typestr;
|
|
int type;
|
|
|
|
sc->sc_dev = self;
|
|
|
|
/* Map i/o space. */
|
|
if (bus_space_map(iot, ia->ia_io[0].ir_addr, ATE_NPORTS, 0, &ioh)) {
|
|
aprint_error(": can't map i/o space\n");
|
|
return;
|
|
}
|
|
|
|
sc->sc_bst = iot;
|
|
sc->sc_bsh = ioh;
|
|
|
|
/* Determine the card type and get ethernet address. */
|
|
type = ate_detect(iot, ioh, myea);
|
|
switch (type) {
|
|
case FE_TYPE_AT1700T:
|
|
typestr = "AT-1700T/RE2001";
|
|
break;
|
|
case FE_TYPE_AT1700BT:
|
|
typestr = "AT-1700BT/RE2003";
|
|
break;
|
|
case FE_TYPE_AT1700FT:
|
|
typestr = "AT-1700FT/RE2009";
|
|
break;
|
|
case FE_TYPE_AT1700AT:
|
|
typestr = "AT-1700AT/RE2005";
|
|
break;
|
|
case FE_TYPE_AT_UNKNOWN:
|
|
typestr = "unknown AT-1700/RE2000";
|
|
break;
|
|
|
|
default:
|
|
/* Unknown card type: maybe a new model, but... */
|
|
aprint_error(": where did the card go?!\n");
|
|
panic("unknown card");
|
|
}
|
|
|
|
aprint_normal(": %s Ethernet\n", typestr);
|
|
|
|
/* This interface is always enabled. */
|
|
sc->sc_stat |= FE_STAT_ENABLED;
|
|
|
|
/*
|
|
* Do generic MB86960 attach.
|
|
*/
|
|
mb86960_attach(sc, myea);
|
|
|
|
mb86960_config(sc, NULL, 0, 0);
|
|
|
|
/* Establish the interrupt handler. */
|
|
isc->sc_ih = isa_intr_establish(ia->ia_ic, ia->ia_irq[0].ir_irq,
|
|
IST_EDGE, IPL_NET, mb86960_intr, sc);
|
|
if (isc->sc_ih == NULL)
|
|
aprint_error_dev(sc->sc_dev,
|
|
"couldn't establish interrupt handler\n");
|
|
}
|