NetBSD/sys/arch/sun3/conf/GENERIC3X

133 lines
3.5 KiB
Plaintext

# $NetBSD: GENERIC3X,v 1.7 1997/05/07 02:20:27 lukem Exp $
#
# GENERIC Sun3x (3/80, 3/470)
# Supports root on: le0, sd*
#
include "arch/sun3x/conf/std.sun3x"
# Machines to be supported by this kernel
# options FPU_EMULATE # XXX - Ever needed?
# Needs to be set per system. i.e change these as you see fit
maxusers 4
# Standard system options
options KTRACE # system call tracing support
# Debugging options. Uncomment either these:
options DDB
#options SYMTAB_SPACE=0x1C000
# ... or these for KGDB (gdb remote target)
#makeoptions DEBUG="-g" # debugging symbols for gdb
#options KGDB
#options KGDBDEV=0x0C01 # ttya=0C00 ttyb=0C01
# Filesystem options
file-system FFS # ufs file system
file-system NFS # nfs client support
file-system CD9660 # ISO 9660 + Rock Ridge file system
file-system MSDOSFS # MS-DOS FAT file system
file-system FDESC # /dev/fd/*
file-system KERNFS # /kern
file-system NULLFS # loopback file system
file-system PROCFS # /proc
file-system UNION # union file system
file-system MFS # memory-based filesystem
options NFSSERVER # nfs server support
options FIFO # FIFOs; RECOMMENDED
# Networking options
options INET # IP prototol stack support
#options GATEWAY # IP packet forwarding
options TCP_COMPAT_42 # TCP bug compatibility with 4.2BSD
# XXX - Work-around for root on slow servers (insurance...)
options NFS_BOOT_RWSIZE=1024
# Compatability options
options COMPAT_SUNOS # can run SunOS 4.1.1 executables
options COMPAT_43 # and 4.3BSD and ...
options COMPAT_12 # NetBSD 1.2
options UCONSOLE # Allow non-root TIOCCONS
# Sun3x-specific debugging options
#options PMAP_DEBUG
#options VMFAULT_TRACE
#options SYSCALL_DEBUG
#options EXEC_DEBUG
#options DIAGNOSTIC
#options SCSIDEBUG
config netbsd root on ? type ?
#
# Serial ports
#
zstty0 at zsc1 channel 0 # ttya
zstty1 at zsc1 channel 1 # ttyb
kbd0 at zsc0 channel 0 # keyboard
ms0 at zsc0 channel 1 # mouse
#
# Network devices
#
# Lance Ethernet (only onboard)
le0 at obio0 addr 0x65002000 ipl 3
#
# Disk and tape devices
#
# Note the flags on the esp entries below, that work around
# deficiencies in the current driver:
# bits 0-7: disable disconnect/reselect for the corresponding target
# bits 8-15: disable synch negotiation for target [bit-8]
# Note: targets 4-7 have disconnect/reselect enabled on the premise
# that tape devices normally have one of these targets. Tape
# devices should be allowed to disconnect for the SCSI bus
# to operate acceptably.
#
# Emulex SCSI (3/80 only)
esp0 at obio0 addr 0x66000000 ipl 2 flags 0xff0f
# Floppy drive
fdc0 at obio0 addr 0x6e000000 ipl 6 vect 0x40
fd0 at fdc0 # First (and only) floppy drive.
#
# Frame buffer devices
#
# bwtwo - Monochrome frame buffer.
bwtwo0 at obmem0 addr 0x50400000 ipl 4
#
# SCSI infrastructure
#
scsibus* at scsi?
sd* at scsibus? target ? lun ? # SCSI disks
st* at scsibus? target ? lun ? # SCSI tapes
cd* at scsibus? target ? lun ? # SCSI CD-ROMs
ch* at scsibus? target ? lun ? # SCSI changer devices
ss* at scsibus? target ? lun ? # SCSI scanners
uk* at scsibus? target ? lun ? # unknown SCSI devices
# Memory-disk drivers
pseudo-device md 2
# Misc.
pseudo-device loop 1 # network loopback
pseudo-device bpfilter 8 # packet filter
pseudo-device sl 2 # CSLIP
pseudo-device ppp 2 # PPP
pseudo-device tun 2 # network tunneling over tty
#pseudo-device ipfilter # ip filter
pseudo-device pty 64 # pseudo-terminals
#pseudo-device vnd 4 # paging to files
#pseudo-device ccd 4 # concatenated disks