NetBSD/sys/arch/i386/conf/LAMB

366 lines
13 KiB
Plaintext

# $NetBSD: LAMB,v 1.1 2000/11/26 03:28:41 itojun Exp $
#
# LAMB -- for "LAMB" router, http://www.wildlab.com/
#
include "arch/i386/conf/std.i386"
# based on:
#ident "GENERIC-Revision: 1.378"
maxusers 32 # estimated number of users
# CPU support. At least one is REQUIRED.
options I386_CPU
options I486_CPU
options I586_CPU
options I686_CPU
# CPU-related options.
options MATH_EMULATE # floating point emulation
options VM86 # virtual 8086 emulation
options USER_LDT # user-settable LDT; used by WINE
# eliminate delay no-ops in I/O; recommended on all but very old machines
#options DUMMY_NOPS
# delay between "rebooting ..." message and hardware reset, in milliseconds
#options CPURESET_DELAY=2000
# This option allows you to force a serial console at the specified
# I/O address. see console(4) for details.
#options "CONSDEVNAME=\"com\"",CONADDR=0x2f8,CONSPEED=57600
# you don't want the option below ON iff you are using the
# serial console option of the new boot strap code.
#options CONS_OVERRIDE # Always use above! independent of boot info
# The following options override the memory sizes passed in from the boot
# block. Use them *only* if the boot block is unable to determine the correct
# values. Note that the BIOS may *correctly* report less than 640k of base
# memory if the extended BIOS data area is located at the top of base memory
# (as is the case on most recent systems).
#options REALBASEMEM=639 # size of base memory (in KB)
#options REALEXTMEM=15360 # size of extended memory (in KB)
# Standard system options
options UCONSOLE # users can use TIOCCONS (for xconsole)
options INSECURE # disable kernel security levels
options RTC_OFFSET=0 # hardware clock is this many mins. west of GMT
options NTP # NTP phase/frequency locked loop
options KTRACE # system call tracing via ktrace(1)
options SYSVMSG # System V-like message queues
options SYSVSEM # System V-like semaphores
options SYSVSHM # System V-like memory sharing
#options SHMMAXPGS=1024 # 1024 pages is the default
options LKM # loadable kernel modules
# Diagnostic/debugging support options
options DIAGNOSTIC # cheap kernel consistency checks
#options DEBUG # expensive debugging checks/support
#options KMEMSTATS # kernel memory statistics (vmstat -m)
options DDB # in-kernel debugger
options DDB_HISTORY_SIZE=512 # enable history editing in DDB
#options KGDB # remote debugger
#options "KGDB_DEVNAME=\"com\"",KGDBADDR=0x3f8,KGDBRATE=9600
#makeoptions DEBUG="-g" # compile full symbol table
# Compatibility options
options COMPAT_NOMID # compatibility with 386BSD, BSDI, NetBSD 0.8,
options COMPAT_09 # NetBSD 0.9,
options COMPAT_10 # NetBSD 1.0,
options COMPAT_11 # NetBSD 1.1,
options COMPAT_12 # NetBSD 1.2,
options COMPAT_13 # NetBSD 1.3,
options COMPAT_14 # NetBSD 1.4,
options COMPAT_43 # and 4.3BSD
options COMPAT_386BSD_MBRPART # recognize old partition ID
options COMPAT_SVR4 # binary compatibility with SVR4
options COMPAT_IBCS2 # binary compatibility with SCO and ISC
options COMPAT_LINUX # binary compatibility with Linux
options COMPAT_FREEBSD # binary compatibility with FreeBSD
#options COMPAT_PECOFF # kernel support to run Win32 apps
# File systems
file-system FFS # UFS
file-system EXT2FS # second extended file system (linux)
file-system LFS # log-structured file system
file-system MFS # memory file system
file-system NFS # Network File System client
file-system NTFS # Windows/NT file system (experimental)
file-system CD9660 # ISO 9660 + Rock Ridge file system
file-system MSDOSFS # MS-DOS file system
file-system FDESC # /dev/fd
file-system KERNFS # /kern
file-system NULLFS # loopback file system
file-system OVERLAY # overlay file system
file-system PORTAL # portal filesystem (still experimental)
file-system PROCFS # /proc
file-system UMAPFS # NULLFS + uid and gid remapping
file-system UNION # union file system
file-system CODA # Coda File System; also needs vcoda (below)
# File system options
options QUOTA # UFS quotas
#options FFS_EI # FFS Endian Independent support
options SOFTDEP # FFS soft updates support.
options NFSSERVER # Network File System server
#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
# immutable) behave as system flags.
# Networking options
#options GATEWAY # packet forwarding
options INET # IP + ICMP + TCP + UDP
options INET6 # IPV6
#options IPSEC # IP security
#options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
#options IPSEC_DEBUG # debug for IP security
#options MROUTING # IP multicast routing
options NS # XNS
#options NSIP # XNS tunneling over IP
options ISO,TPIP # OSI
#options EON # OSI tunneling over IP
options CCITT,LLC,HDLC # X.25
options NETATALK # AppleTalk networking protocols
options PPP_BSDCOMP # BSD-Compress compression support for PPP
options PPP_DEFLATE # Deflate compression support for PPP
options PPP_FILTER # Active filter support for PPP (requires bpf)
options PFIL_HOOKS # pfil(9) packet filter hooks
options IPFILTER_LOG # ipmon(8) log support
# Compatibility with 4.2BSD implementation of TCP/IP. Not recommended.
#options TCP_COMPAT_42
# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
#options PNPBIOSVERBOSE # verbose PnP BIOS messages
#options PNPBIOSDEBUG # more fulsome Pnp BIOS debugging messages
options NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM
#
# wscons options
#
# builtin terminal emulations
#options WSEMUL_SUN # sun terminal emulation
options WSEMUL_VT100 # VT100 / VT220 emulation
# different kernel output - see dev/wscons/wsdisplayvar.h
options WS_KERNEL_FG=WSCOL_GREEN
#options WS_KERNEL_BG=WSCOL_BLACK
# compatibility to other console drivers
options WSDISPLAY_COMPAT_PCVT # emulate some ioctls
options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls
options WSDISPLAY_COMPAT_USL # VT handling
options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes
# see dev/pckbc/wskbdmap_mfii.c for implemented layouts
#options PCKBD_LAYOUT="(KB_DE | KB_NODEAD)"
# allocate a number of virtual screens at autoconfiguration time
#options WSDISPLAY_DEFAULTSCREENS=4
# use a large software cursor that doesn't blink
options PCDISPLAY_SOFTCURSOR
# modify the screen type of the console; defaults to "80x25"
#options VGA_CONSOLE_SCREENTYPE="\"80x24\""
# Kernel root file system and dump configuration.
config netbsd root on ? type ?
#config netbsd root on sd0a type ffs
#config netbsd root on ? type nfs
#
# Device configuration
#
mainbus0 at root
#apm0 at mainbus0 # Advanced power management
# Tuning for power management, see apm(4) for more details.
#options APM_NO_IDLE # Don't call BIOS CPU idle function
#options APM_V10_ONLY # Use only the APM 1.0 calls
#options APM_NO_POWEROFF # Don't power off on halt(8)
#options APM_POWER_PRINT # Print stats on the console
#options APM_DISABLE_INTERRUPTS=0 # Don't disable interrupts
# Basic Bus Support
# Plug-and-Play BIOS and attached devices
#pnpbios* at mainbus?
# mainboard audio chips
#ess* at pnpbios? index ? # ESS AudioDrive
#sb* at pnpbios? index ? # NeoMagic 256AV in sb mode
#wss* at pnpbios? index ? # NeoMagic 256AV in wss mode
#ym* at pnpbios? index ? # OPL3-SA3
# com port
# If enabled, consider changing "com0", "com1", and "com2" under "ISA Serial
# Interfaces" to "com*", otherwise com2 will attach at pnpbios? and there
# will be no com0. A side effect is pcmcia (and other) com? previously
# starting at com3 may attach as com1 or com2.
#com* at pnpbios? index ? # serial ports
# parallel port
# The above "com*" comments apply, cf. "lpt0" under "ISA parallel
# "printer interfaces".
#lpt* at pnpbios? index ? # parallel ports
#pckbc* at pnpbios? index ? # PC keyboard/mouse controller
#fdc* at pnpbios? index ? # floppy controller
# Configure PCI using BIOS information
#options PCIBIOS # PCI BIOS support
#options PCIBIOSVERBOSE # PCI BIOS verbose info
#options PCIBIOS_ADDR_FIXUP # fixup PCI I/O addresses
#options PCIBIOS_BUS_FIXUP # fixup PCI bus numbering
#options PCIBIOS_INTR_FIXUP # fixup PCI interrupt routing
#options PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9 or 11
#options PCIBIOS_INTR_GUESS # see pcibios(4)
#options PCIINTR_DEBUG # super-verbose PCI interrupt fixup
# ISA bus support
isa* at mainbus?
# ISA Plug-and-Play bus support
isapnp0 at isa?
# Coprocessor Support
# Math Coprocessor support
npx0 at isa? port 0xf0 irq 13 # x86 math coprocessor
# Console Devices
# ISA console
#pc0 at isa? port 0x60 irq 1 # pccons generic PC console driver
# Keyboard layout configuration for pccons
#options FRENCH_KBD
#options FINNISH_KBD
#options GERMAN_KBD
#options NORWEGIAN_KBD
# pccons-specific options:
#options XSERVER_DDB # PF12 gets you into DDB when X is running
#options XSERVER # X server support
# wscons
pckbc0 at isa? # pc keyboard controller
pckbd* at pckbc? # PC keyboard
# "opms" should not be enabled together with "pms" or "pmsi"
pms* at pckbc? # PS/2 mouse for wsmouse
pmsi* at pckbc? # PS/2 "Intelli"mouse for wsmouse
#opms* at pckbc? # backwards compatible PS/2 mouse
vga0 at isa?
pcdisplay0 at isa? # CGA, MDA, EGA, HGA
wsdisplay* at vga? console ?
wsdisplay* at pcdisplay? console ?
wskbd* at pckbd? console ?
wsmouse* at pms? mux 0
wsmouse* at pmsi? mux 0
# no buzzer installed
#pcppi0 at isa?
#sysbeep0 at pcppi?
#midi* at pcppi? # MIDI interface to the PC speaker
# Serial Devices
# ISA serial interfaces
com0 at isa? port 0x3f8 irq 4 # Standard PC serial ports
# Parallel Printer Interfaces
# ISA parallel printer interfaces
lpt0 at isa? port 0x378 irq 7 # standard PC parallel ports
lpt1 at isa? port 0x278
lpt2 at isa? port 0x3bc
# IDE and related devices
# ISA Plug-and-Play IDE controllers
wdc* at isapnp?
# ISA ST506, ESDI, and IDE controllers
# Use flags 0x01 if you want to try to use 32bits data I/O (the driver will
# fall back to 16bits I/O if 32bits I/O are not functional).
# Some controllers pass the initial 32bit test, but will fail later.
wdc0 at isa? port 0x1f0 irq 14 flags 0x00
wdc1 at isa? port 0x170 irq 15 flags 0x00
# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd* at wdc? channel ? drive ? flags 0x0000
# ATAPI bus support
atapibus* at wdc? channel ?
# ATAPI devices
# flags have the same meaning as for IDE drives.
cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown
# Network Interfaces
# ISA network interfaces
ne0 at isa? port 0x200 irq 3 # LOCAL (left)
ne1 at isa? port 0x300 irq 10 # GLOBAL (right)
# Pull in optional local configuration
#include "arch/i386/conf/LAMB.local"
# Pseudo-Devices
# disk/mass storage pseudo-devices
pseudo-device ccd 4 # concatenated/striped disk devices
#pseudo-device raid 4 # RAIDframe disk driver
#options RAID_AUTOCONFIG # auto-configuration of RAID components
pseudo-device md 1 # memory disk device (ramdisk)
pseudo-device vnd 4 # disk-like interface to files
# network pseudo-devices
pseudo-device bpfilter 8 # Berkeley packet filter
pseudo-device ipfilter # IP filter (firewall) and NAT
pseudo-device loop # network loopback
pseudo-device ppp 2 # Point-to-Point Protocol
pseudo-device sl 2 # Serial Line IP
pseudo-device strip 2 # Starmode Radio IP (Metricom)
pseudo-device tun 2 # network tunneling over tty
pseudo-device gre 2 # generic L3 over IP tunnel
pseudo-device ipip 2 # IP Encapsulation within IP (RFC 2003)
pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933)
#pseudo-device faith 1 # IPv[46] tcp relay translation i/f
#pseudo-device stf 1 # 6to4 IPv6 over IPv4 encapsulation
# miscellaneous pseudo-devices
pseudo-device pty # pseudo-terminals
pseudo-device tb 1 # tablet line discipline
pseudo-device sequencer 1 # MIDI sequencer
# rnd works; RND_COM does not on port i386 yet.
pseudo-device rnd # /dev/random and in-kernel generator
#options RND_COM # use "com" randomness as well (BROKEN)
# a pseudo device needed for Coda # also needs CODA (above)
pseudo-device vcoda 4 # coda minicache <-> venus comm.
# mouse & keyboard multiplexor pseudo-devices
pseudo-device wsmux 2