183 lines
6.6 KiB
Plaintext
183 lines
6.6 KiB
Plaintext
Installing NetBSD is a relatively complex process, but if you have
|
|
this document in hand it shouldn't be too much trouble.
|
|
|
|
There are several ways to install NetBSD onto a disk. If your Sparcstation
|
|
is hooked up in a network you can find find a server and arrange for a
|
|
diskless setup which is a convenient way to install on a machine with
|
|
a single disk attached. Alternatively, you could use SunOS (booted from
|
|
a local disk) and install NetBSD onto a second disk. For the latter method,
|
|
skip to the section "Installing from SunOS" below.
|
|
|
|
Installing using a diskless setup.
|
|
|
|
First, you must setup a diskless client configuration on a server. Consult
|
|
your server installation documents on how to proceed with this.
|
|
Put all the *.tar.gz files you want to install into the root directory
|
|
for your client on the server.
|
|
|
|
Next, unpack base.tar.gz on the server in the root directory for your machine.
|
|
A few configuration files need to be edited:
|
|
|
|
<root>/etc/hosts
|
|
<root>/etc/myname
|
|
<root>/etc/fstab
|
|
|
|
Boot your workstation from the server by entering the appropriate `boot'
|
|
command at the monitor prompt. Depending on the PROM version in your machine,
|
|
this command takes one of the following forms:
|
|
|
|
> b le()netbsd -s # for sun4 monitors
|
|
ok boot le()netbsd -s # for version 1 OpenBOOT ROMs
|
|
ok boot net netbsd -s # for version 2 OpenBOOT ROMs
|
|
|
|
This will boot the NetBSD kernel in single-user mode.
|
|
|
|
[[
|
|
NOTE: the latter two examples assume you operate the OpenBOOT ROM in
|
|
"new command mode". If your machine comes up and gives you a `>' prompt
|
|
instead of `ok', type:
|
|
|
|
>n # enter native OpenBOOT mode
|
|
ok setenv sunmon-compat? false # make it permanent
|
|
ok
|
|
]]
|
|
|
|
Start the installation procedure:
|
|
|
|
netbsd# ./install.sh
|
|
|
|
|
|
This script will do most of the work of transferring the system from the
|
|
tar files onto your disk. You will frequently be asked for confirmation
|
|
before the script proceeds with each phase of the installation process.
|
|
Occasionally, you'll have to provide a piece of information such as the
|
|
name of the disk you want to install on or IP addresses and domain names
|
|
you want to assign.
|
|
|
|
The installation script goes through the following phases:
|
|
|
|
- determination of the disk to install NetBSD on
|
|
- checking of the partition information on the disk
|
|
- creating and mounting the NetBSD filesystems
|
|
- setup of IP configuration
|
|
- extraction of the distribution tar files
|
|
- installation of boot programs
|
|
|
|
|
|
Now try a reboot. (If needed, swap your scsi id's first). Initially
|
|
I'd suggest you "boot sd()netbsd -bs", then try multiuser after that.
|
|
if you boot single-user the NetBSD incantation to make the root
|
|
filesystem writable is
|
|
|
|
netbsd# mount -u /dev/sd0a /
|
|
|
|
The Sun monitor normally tries to load a file called "vmunix". On
|
|
OpenBOOT ROM systems you can change it to load NetBSD instead using
|
|
the following commands:
|
|
|
|
On version 1 OpenBOOT ROMs:
|
|
>n
|
|
ok setenv boot-from sd(0,0,0)netbsd
|
|
ok
|
|
|
|
On version 2 OpenBOOT ROMs:
|
|
ok setenv boot-file netbsd
|
|
ok setenv boot-device /sbus/esp/sd@0,0
|
|
|
|
|
|
Congratulations, you have successfully installed NetBSD 1.0. When you
|
|
reboot into NetBSD, you should log in as "root" at the login prompt.
|
|
There is no initial password, but if you're using the machine in a
|
|
networked environment, you should create yourself an account and
|
|
protect it and the "root" account with good passwords.
|
|
|
|
Some of the files in the NetBSD 1.0 distribution might need to be
|
|
tailored for your site. In particular, the /etc/sendmail.cf file will
|
|
almost definitely need to be adjusted, and other files in /etc will
|
|
probably need to be modified. If you are unfamiliar with UN*X-like
|
|
system administration, it's recommended that you buy a book that
|
|
discusses it.
|
|
|
|
|
|
|
|
Installing from SunOS.
|
|
|
|
You need a SunOS machine to install NetBSD. You also need at
|
|
least the following pieces:
|
|
|
|
the *.tar.gz files you want to install (as a minimum, base.tar.gz)
|
|
gzip (GNU gzip) SunOS binary
|
|
gtar (GNU tar) SunOS binary
|
|
the "install.sh" script
|
|
a "/boot" file from a SunOS sun4c machine
|
|
a kernel, most likely "/netbsd"
|
|
|
|
All these pieces, except "/boot", are supplied in the NetBSD/sparc
|
|
distribution.
|
|
|
|
You need to format and partition the disk using SunOS (since
|
|
NetBSD/sparc uses SunOS disk labels.) Give yourself adequate
|
|
partition sizes. Here is an example layout:
|
|
|
|
partition size offset will be..
|
|
sd2a 28140 0 /
|
|
sd2b 16170 28140 swap
|
|
sd2c 204540 0 `whole disk'
|
|
sd2g 160230 44310 /usr
|
|
|
|
BTW, These are not recommended sizes. They simply match the first
|
|
(tiny) disk that NetBSD/sparc ran on.
|
|
|
|
Use SunOS to newfs the partitions which will have filesystems on them.
|
|
(NetBSD's filesystem format is identical to SunOS).
|
|
|
|
sunos# newfs /dev/rsd2a
|
|
[... lots of output]
|
|
sunos# newfs /dev/rsd2g
|
|
[... lots of output]
|
|
|
|
NOTE: If you are able to, there is a performance benefit from
|
|
newfs'ing using NetBSD. If you newfs using the NetBSD newfs command,
|
|
be sure to use the -O flag for your / partition, so that newfs will
|
|
use the 4.3BSD filesystem format, rather than the new 4.4BSD filesystem
|
|
format. If you forget, you will not be able to boot -- the SunOS boot
|
|
blocks do not understand the extended 4.4BSD filesystem format.
|
|
|
|
Mount those partitions in a tree formation, under /mnt; ie:
|
|
|
|
sunos# df
|
|
Filesystem kbytes used avail capacity Mounted on
|
|
[...]
|
|
/dev/sd2a 11501 0 11501 0% /mnt
|
|
/dev/sd2g 179529 0 179529 0% /mnt/usr
|
|
|
|
Place a standard SunOS "/boot" program in /mnt (your new root
|
|
partition), and use the SunOS command "installboot" to make it work.
|
|
The installboot man page says to do something like this:
|
|
|
|
sunos# cp /boot /mnt/boot
|
|
sunos# /usr/mdec/installboot -vlt /mnt/boot /usr/mdec/bootsd /dev/rsd2a
|
|
|
|
You can now extract the provided "*.tar.gz files onto your disk. The
|
|
provided script, "install.sh" will help you:
|
|
|
|
sunos# ls -FC
|
|
base.tar.gz etc.tar.gz man.tar.gz secr.tar.gz
|
|
comp.tar.gz games.tar.gz misc.tar.gz text.tar.gz
|
|
install.sh netbsd.id3_scsi
|
|
sunos# ./install.sh
|
|
[...]
|
|
|
|
This script NEEDS gzip and gtar (GNU gzip and GNU tar) on your
|
|
execution path! The tar files are in a "new format" that includes
|
|
directory information, and SunOS tar will not read them. Statically
|
|
linked versions of these programs for SunOS are supplied in the
|
|
distribution.
|
|
|
|
After the files have been extracted, repair /mnt/etc/fstab to match
|
|
your actual disk layout. (Minus the "/mnt" component of each path, of
|
|
course :-)
|
|
|
|
Now proceed to reboot the machine as described above in "Installing
|
|
using a diskless setup".
|