NetBSD/distrib/notes/hp300/install

117 lines
4.7 KiB
Plaintext

.\" $NetBSD: install,v 1.4 1999/01/13 07:30:04 ross Exp $
.\"
.\" Copyright (c) 1999 The NetBSD Foundation, Inc.
.\" All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\" notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\" notice, this list of conditions and the following disclaimer in the
.\" documentation and/or other materials provided with the distribution.
.\" 3. All advertising materials mentioning features or use of this software
.\" must display the following acknowledgement:
.\" This product includes software developed by the NetBSD
.\" Foundation, Inc. and its contributors.
.\" 4. Neither the name of The NetBSD Foundation nor the names of its
.\" contributors may be used to endorse or promote products derived
.\" from this software without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
.\" ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
.\" TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
.\" PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
.\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
.\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
.\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
.\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
.\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
.\" POSSIBILITY OF SUCH DAMAGE.
.\"
The miniroot's install program is very simple to use. It will guide
you through the entire process, and is well automated. Additional
improvements are planned for future releases.
.Pp
The miniroot's install program will:
.Bl -bullet
.It
Allow you to place disklabels on additional disks.
Note that partition sizes and offsets are expressed
in sectors. When you fill out the disklabel, you will
need to specify partition types and filesystem parameters.
If you're unsure what the these values should be, use the
following:
.Bd -ragged
fstype: 4.2BSD
fsize: 1024
bsize: 4096
cpg: 16
.Ed
If the partition will be a swap partition, use the following:
.Bd -ragged
fstype: swap
fsize: 0 (or blank)
bsize: 0 (or blank)
cpg: 0 (or blank)
.Ed
.Pp
You will also need to specify the number of partitions.
The number of partitions is determined by the `index' of
the last partition letter, where a == 1, b == 2, etc.
Therefore, if the last filled partition is partition `g',
there are 7 partitions. Any partitions with size of 0
may be removed from the list.
.Pp
If the disk is the boot disk, you _must_ offset the root
partition (`a') one cylinder, as the hp300 boot code
if large enough to spill past the label area. In this case,
the `c' partition must be fstype `boot'.
.Pp
Anything after a `#' is a comment.
.Pp
The following is an example disklabel partition map:
.Bd -literal
7 partitions:
# size offset fstype [fsize bsize cpg]
a: 30912 448 4.2BSD 1024 8192 16 # (Cyl. 1 - 69)
b: 130816 31360 swap # (Cyl. 70 - 361)
c: 1296512 0 boot # (Cyl. 0 - 2893)
e: 81984 162176 4.2BSD 1024 8192 16 # (Cyl. 362 - 544)
f: 102592 244160 4.2BSD 1024 4096 16 # (Cyl. 545 - 773)
g: 949760 346752 4.2BSD 1024 8192 16 # (Cyl. 774 - 2893)
.Ed
.It
Create filesystems on target partitions.
.It
Allow you to set up your system's network configuration.
Remember to specify host names without the domain name
appended to the end. For example use `foo' instead of
`foo.bar.org'. If, during the process of configuring
the network interfaces, you make a mistake, you will
be able to re-configure that interface by simply selecting
it for configuration again.
.It
Mount target filesystems. You will be given the opportunity
to manually edit the resulting
.Pa /etc/fstab .
.It
Extract binary sets from the media of your choice.
.It
Copy configuration information gathered during the
installation process to your root filesystem.
.It
Make device nodes in your root filesystem.
.It
Copy a new kernel onto your root partition.
.It
Install a new boot block.
.It
Check your filesystems for integrity.
.El
.Pp
First-time installation on a system through a method other than the
installation program is possible, but strongly discouraged.