75 lines
2.8 KiB
Plaintext
75 lines
2.8 KiB
Plaintext
Before you start you might need to consider your disk configuration
|
|
to sort out a quirk in SCSI-ID to SD-UNIT mapping that exists on
|
|
Sun Sparcstations.
|
|
|
|
Upon leaving the factory, SunOS and the OpenBOOT ROM map according to
|
|
this table:
|
|
|
|
SCSI-ID -> SunOS SD-UNIT
|
|
0 sd3
|
|
1 sd1
|
|
2 sd2
|
|
3 sd0
|
|
4 sd4
|
|
5 sd5
|
|
6 sd6
|
|
|
|
Unlike SunOS and the OpenBOOT ROM, a generic NetBSD kernel numbers
|
|
scsi drives sequentially as it finds them. The drive with the
|
|
lowest scsi-id will be called sd0, the next one sd1, etc.
|
|
|
|
To ease the installation process, the default NetBSD kernel in the
|
|
distribution is setup to match the Sun mapping above by hard-wiring
|
|
scsi-id#3 to sd0 and scsi-id#0 to sd3. The remaining drives will be
|
|
dynamically mapped to other sd* numbers.
|
|
|
|
A truely generic NetBSD kernel is also provided as `/netbsd.GENERIC',
|
|
which will do the standard NetBSD probe ordering. If your configuration
|
|
differs from the default Sun setup, you can try to use this kernel to
|
|
complete the installation.
|
|
|
|
NOTE: this is also a concern when you start building your own customised
|
|
kernels.
|
|
|
|
|
|
Your OpenBOOT ROM may need some setup. make sure you boot from `new
|
|
command mode'. If your machine comes up and gives you a `>' prompt
|
|
instead of `ok', type:
|
|
|
|
>n
|
|
ok setenv sunmon-compat? false
|
|
ok
|
|
|
|
This is needed because the NetBSD kernel relies on functionality provided
|
|
by OpenBOOT ROMs -- the ability to pass down Forth commands and have them
|
|
executed in the ROM -- that appears to go away when the OpenBOOT ROM
|
|
operates in `old monitor compatibility' mode.
|
|
|
|
Also, you cannot use the security modes of the sparc OpenBOOT ROM.
|
|
|
|
ok setenv security-mode none
|
|
|
|
|
|
|
|
If you're installing NetBSD/sparc for the first time it's a good idea
|
|
to look at the partition sizes of disk you intend installing NetBSD on.
|
|
|
|
Asumming a classic partition scheme with root (`/') and /usr filesystems,
|
|
a comfortable size for the NetBSD root filesystem partition is about 20MB;
|
|
a good initial size for the swap partition is twice the amount of physical
|
|
memory in your machine (though, unlike SunOS 4.x, there are no restrictions
|
|
on the size of the swap partition that would render part of your memory
|
|
unusable). A full binary installation takes about 60MB in `/usr'.
|
|
|
|
Some network devices (i.e. the built-in `le' interface on sun4m machines)
|
|
allow a choice between operating on a UTP or a AUI port. The `le' driver
|
|
supports automatic detection of the port which is actually connected to
|
|
the wire.
|
|
|
|
If automatic detection is not available or not working properly in your
|
|
environment, you may have to specify the type connection using the
|
|
`media' parameter of ifconfig(8). During installation, you'll get the
|
|
opportunity to specify the appropriate medium. Use ``10base5/AUI''
|
|
to select the AUI connector, or ``10baseT/UTP'' to select the UTP connector.
|
|
|