81 lines
2.6 KiB
Plaintext
81 lines
2.6 KiB
Plaintext
You will need an AmigaDOS hard drive prep tool to prepare you hard
|
|
drives for use with NetBSD/amiga. HDToolBox is provided with the
|
|
system software and on floppy installation disks since Release 2.0
|
|
of AmigaDOS so we will provide instructions for its use.
|
|
|
|
Preparing you hard disk with HDToolBox:
|
|
|
|
A full explanation of HDToolBox can be found with your
|
|
AmigaDOS manuals and is beyond the scope of this document.
|
|
|
|
Note you will be modifying your HD's if you mess something
|
|
up here you could lose everything on all the drives that
|
|
you configure. It is therefore advised that you:
|
|
|
|
Write down your current configurations. Do this
|
|
by examining each partition on the drive and the
|
|
drives parameters (from Change drive type.)
|
|
|
|
Back up the partitions you are keeping.
|
|
|
|
What you need to do is partition your drives; creating
|
|
at least root, swap and /usr partitions and possibly at least
|
|
one more for /local if you have the space.
|
|
|
|
This should be done as the HDToolBox manual describes. One thing
|
|
to note is that if you are not using a Commodore controller you
|
|
will need to specify the device your SCSI controller uses e.g.
|
|
if you have a Warp Engine you would:
|
|
|
|
from cli,
|
|
hdtoolbox warpdrive.device
|
|
|
|
from wb set the tooltype,
|
|
SCSI_DEVICE_NAME=warpdrive.device
|
|
|
|
The important things you need to do above and beyond normal
|
|
partitioning includes (from Partition Drive section):
|
|
|
|
Marking all NetBSD partitions as non-bootable.
|
|
|
|
Changing the file system parameters of the partitions
|
|
to NetBSD ones. This must be done from the
|
|
partitioning section and `Advanced options' must
|
|
be enabled. To Make the needed changes:
|
|
|
|
- Click the `Adv. Options' button
|
|
- Click the `Change filesystem' button
|
|
|
|
- Choose `Custom File System'
|
|
- Turn off `Automount' if on.
|
|
- Set the dostype to one of these three choices:
|
|
|
|
root partition : 0x4e425207
|
|
swap partition : 0x4e425301
|
|
other partitions: 0x4e425507
|
|
|
|
Here `other' refers to other partitions you will
|
|
format for reading and writing under NetBSD (e.g.
|
|
/usr)
|
|
|
|
Make sure you hit the return key to enter this value
|
|
as some versions of HDToolBox will forget your entry
|
|
if you don't.
|
|
|
|
- Turn custom boot code off
|
|
- Set Reserved Blocks start and end to 0.
|
|
- Click Ok.
|
|
|
|
Mask and maxtransfer are not used with NetBSD.
|
|
|
|
Until you compile your own kernel your swap partition
|
|
must exist on the drive that also holds your root
|
|
partition.
|
|
|
|
|
|
Once this is done NetBSD/amiga will be able to recognize your
|
|
disks and which partitions it should use.
|
|
|
|
>>> Should the miniroot transfer to the swap partition instructions
|
|
>>> go here?
|