681 lines
19 KiB
Plaintext
681 lines
19 KiB
Plaintext
.\" $NetBSD: prep,v 1.17 2003/07/26 17:07:04 salo Exp $
|
|
.
|
|
There are two installation tools available.
|
|
The traditional miniroot
|
|
installer is script-based and may be netbooted or may be dumped to a disk
|
|
and run locally.
|
|
The ramdisk kernel with the
|
|
.Ic sysinst
|
|
installation utility is more flexible,
|
|
but can only be netbooted and has not been extensively tested.
|
|
.Pp
|
|
There are several possible installation configurations described in this
|
|
document.
|
|
Other configurations are possible, but less common.
|
|
If you are unable to install based on the information in this document,
|
|
post a message to
|
|
.Mt port-hp300@NetBSD.org
|
|
asking for help.
|
|
The configurations described in this document are as follows:
|
|
.Pp
|
|
.(bullet -compact
|
|
\*M netboots
|
|
.Li SYS_UBOOT
|
|
and then runs the miniroot installation tools or a purely diskless
|
|
installation from a
|
|
.Nx
|
|
server on the same subnet (you must have root access).
|
|
Other server platforms will work, but are described in the NetBSD Diskless
|
|
HOW-TO.
|
|
.Lk http://www.NetBSD.org/Documentation/network/netboot/
|
|
.Pp
|
|
.It
|
|
\*M loads
|
|
.Li SYS_UBOOT
|
|
from a local disk, tape, or floppy
|
|
and then runs the miniroot installation tools or a purely diskless
|
|
installation from a
|
|
.Nx
|
|
server on the same subnet (you must have root access).
|
|
Other server platforms will work, but are described in the NetBSD Diskless
|
|
HOW-TO.
|
|
.Lk http://www.NetBSD.org/Documentation/network/netboot/
|
|
You will need
|
|
.Tn HP-UX
|
|
on your \*M if it does not have a SCSI interface or a floppy drive.
|
|
.Pp
|
|
.It
|
|
\*M loads
|
|
.Li SYS_INST
|
|
from a local disk.
|
|
You partition the drive
|
|
and then run the miniroot installation tools from that drive.
|
|
You will need
|
|
.Tn HP-UX
|
|
on your \*M if it does not have a SCSI interface.
|
|
.bullet)
|
|
The preferred method is to use another
|
|
.Nx
|
|
server to netboot the \*M client.
|
|
This procedure will not
|
|
work on the handful of models which are incapable of netbooting.
|
|
In particular, the 320, 350, 330, 318, and
|
|
319 might not have a recent enough BootROM.
|
|
The BootROM revision is printed when your workstation is first powered on
|
|
(or rebooted).
|
|
Revision B or later will definitely work.
|
|
BootROMs with numeric revisions such as 1.1 (on a 400s) will netboot
|
|
without any problems.
|
|
You can netboot from any built-in or add-on ethernet board on
|
|
a model with a supported BootROM.
|
|
.Pp
|
|
If you have access to a
|
|
.Nx*M
|
|
system, it is
|
|
.Em much
|
|
easier to simply upgrade than to install from scratch.
|
|
Skip down to the section on
|
|
.Sx Upgrading a previously-installed NetBSD System
|
|
.
|
|
.Ss2 Formatting your hard drives
|
|
.
|
|
.Nx*M
|
|
does not have the capability to perform a low-level format of hard
|
|
drives.
|
|
SCSI disks can be formatted on any platform with SCSI support and
|
|
then used on
|
|
.Nx*M .
|
|
HP-IB disks can only be formatted by the
|
|
.Tn HP-UX
|
|
.Xr mediainit 1
|
|
command.
|
|
You may need to first create the device nodes for your disk, as
|
|
.Tn HP-UX
|
|
was never very good about populating
|
|
.Pa /dev/rdsk
|
|
propertly.
|
|
.(disp
|
|
.No # Ic "mknod /dev/dsk/IDs0 b 0 0xSCID00"
|
|
.No # Ic "mknod /dev/rdsk/IDs0 c 4 0xSCID00"
|
|
.No # Ic "mediainit -v /dev/rdsk/IDs0"
|
|
.disp)
|
|
.(item
|
|
.Em ID
|
|
is the HP-IB address (a.k.a. slave) of the disk in hexadecimal.
|
|
This is usually between
|
|
.Li 00
|
|
and
|
|
.Li 07 ,
|
|
but possibly up to
|
|
.Li 1F
|
|
(31 decimal) .
|
|
.item)
|
|
.(item
|
|
.Em SC
|
|
is the Select Code of the disk controller.
|
|
This is usually
|
|
.Li 07
|
|
for slow (i.e. built-in) HP-IB or
|
|
.Li 0E
|
|
(14 decimal) for SCSI or fast HP-IB.
|
|
.item)
|
|
.
|
|
.Ss2 Designing your disk's partition table
|
|
.
|
|
This step can sometimes be a real pain, especially when using
|
|
.Pa SYS_INST .
|
|
It's best to calculate it ahead of time.
|
|
.Pp
|
|
If you are installing to an HP-IB disk,
|
|
you will need information about your disk's geometry, based on 512-byte sectors.
|
|
The file
|
|
.Pa installation/misc/HP-IB.geometry
|
|
in the distribution has geometry information for
|
|
several HP-IB disks, but may be incomplete.
|
|
Geometry may be calculated from an HP-UX
|
|
.Pa /etc/disktab
|
|
entry, but note that HP-UX geometry is based
|
|
on 1024 byte sectors, while
|
|
.Nx 's
|
|
is based on 512 byte sectors.
|
|
You should have all partitions start on cylinder boundaries.
|
|
.Pp
|
|
If you are installing to a SCSI disk, you don't need to worry about the
|
|
details of the geometry.
|
|
Just create a disklabel based on the total
|
|
number of sectors available on the disk.
|
|
.Pp
|
|
.Em A quick note about partitions:
|
|
Since the target disk will become the boot
|
|
disk for your new
|
|
.Nx*M
|
|
installation, you will need to treat the
|
|
.Sq Li a
|
|
and
|
|
.Sq Li c
|
|
partitions in a special manner.
|
|
Due to the size of the
|
|
.Nx*M
|
|
boot program (it spills into the area after the disklabel),
|
|
it is necessary to offset the beginning of the
|
|
.Sq Li a
|
|
partition.
|
|
For HP-IB disks, it is best to offset it by one cylinder from
|
|
the beginning of the disk.
|
|
For SCSI disks, just offset it by 100 KB (200 sectors).
|
|
Later, the
|
|
.Sq Li c
|
|
partition will be marked with the type
|
|
.Sq Li boot
|
|
and may not be used for a file system.
|
|
(For those unfamiliar
|
|
with historic
|
|
.Bx
|
|
partition conventions, the
|
|
.Sq Li c
|
|
partition is defined as the
|
|
.Sq entire disk ,
|
|
or the
|
|
.Sq raw partition . )
|
|
.Pp
|
|
Here is a table of recommended partition sizes for a full install:
|
|
.Bl -column -offset indent Partition Suggested Needed
|
|
.It Partition Ta Suggested Ta Needed
|
|
.It /\ (root) Ta "25 MB" Ta "15 MB"
|
|
.It /usr Ta "150 MB" Ta "100 MB"
|
|
.It /var Ta "20 MB" Ta "5 MB"
|
|
.It swap Ta Em "2-3 *RAM" Ta 6 MB
|
|
.El
|
|
.Pp
|
|
.(Note
|
|
You will need at least a 6 MB swap partition if you are unable to netboot
|
|
the installer, as the miniroot is temporarily placed in this partition.
|
|
.Note)
|
|
.Pp
|
|
Here is an example disklabel from a 7959B HP-IB hard drive:
|
|
.(disp
|
|
# /dev/rrd0a:
|
|
type: HP-IB
|
|
disk: rd7959B
|
|
label:
|
|
flags:
|
|
bytes/sector: 512
|
|
sectors/track: 42
|
|
tracks/cylinder: 9
|
|
sectors/cylinder: 378
|
|
cylinders: 1572
|
|
total sectors: 594216
|
|
rpm: 3600
|
|
interleave: 1
|
|
trackskew: 0
|
|
cylinderskew: 0
|
|
headswitch: 0 # milliseconds
|
|
track-to-track seek: 0 # milliseconds
|
|
drivedata: 0
|
|
|
|
8 partitions:
|
|
# size offset fstype [fsize bsize cpg]
|
|
a: 37800 378 4.2BSD 1024 8192 16 #
|
|
b: 66150 38178 swap 1024 8192 16 #
|
|
c: 594216 0 boot # (Cyl. 0 - 1571)
|
|
d: 489888 104328 4.2BSD 1024 8192 16 #
|
|
.disp)
|
|
.
|
|
.Ss2 Installing the bootstrap program locally
|
|
.
|
|
For earlier models incapable of netbooting, you need to install the
|
|
bootstrap program on a bootable local device, such as a hard disk, floppy
|
|
disk, or tape drive.
|
|
If you will be booting the miniroot over the
|
|
network, then you will be installing
|
|
.Pa installation/misc/SYS_UBOOT .
|
|
.Pp
|
|
If you do not have access to a netboot server to serve the miniroot
|
|
installer, you can use a primitive bootstrap program
|
|
.Pa installation/misc/SYS_INST
|
|
to load the miniroot from a locally attached device (such as a
|
|
disk, tape or CD-R).
|
|
This is not recommended, as
|
|
.Pa SYS_INST
|
|
is difficult to use, buggy, and provides no error checking when
|
|
partitioning your disk.
|
|
.Pp
|
|
If your system has SCSI, this is easy.
|
|
Just take a scratch SCSI disk (hard disk, zip disk, or CD-R)
|
|
and use any computer to dump the bootstrap program to it.
|
|
For example, to dump it to the
|
|
.Li sd1
|
|
disk on a non-i386 platform:
|
|
.(disp
|
|
.No # Ic "dd if=SYS_UBOOT of=/dev/sd1c"
|
|
.disp)
|
|
.Pp
|
|
If your system has a floppy drive, you can write the bootstrap program to
|
|
it using any computer with a floppy drive.
|
|
You will need to dump it using a utility like
|
|
.Ic rawrite
|
|
or
|
|
.Xr dd 1 .
|
|
Make sure to read back from the floppy to verify that the file has been
|
|
written correctly.
|
|
.Pp
|
|
If your system does not have SCSI or a floppy drive, you will need a
|
|
bootable operating system on your \*M so you can write files to the HP-IB
|
|
device.
|
|
You should probably write the bootstrap program to the disk you
|
|
will be installing
|
|
.Nx
|
|
onto.
|
|
.Pp
|
|
Using
|
|
.Tn HP-UX
|
|
to write to an HP-IB disk:
|
|
.(disp
|
|
.No # Ic "dd if=SYS_UBOOT of=/dev/rdsk/IDs0"
|
|
.disp)
|
|
.(item
|
|
.Em ID
|
|
is the HP-IB address (a.k.a. slave) of the disk in hexadecimal.
|
|
This is usually between
|
|
.Li 00
|
|
and
|
|
.Li 07 ,
|
|
but possibly up to
|
|
.Li 1F
|
|
(31 decimal) .
|
|
.item)
|
|
.Pp
|
|
Using
|
|
.Tn HP-UX
|
|
to write to an HP-IB tape:
|
|
.(disp
|
|
.No # Ic "dd if=SYS_UBOOT of=/dev/rmt/0mnb obs=20b conv=sync"
|
|
.disp)
|
|
.
|
|
.Ss2 Installing the miniroot file system locally
|
|
.
|
|
This step is only necessary if you are not loading the miniroot
|
|
installer from a netboot server.
|
|
Follow the same procedure for the bootstrap program, except use the
|
|
uncompressed miniroot file system
|
|
.No ( Pa installation/miniroot/miniroot.fs.gz No )
|
|
instead of the bootstrap program.
|
|
The only quirk is that you should place it at the offset of the swap
|
|
partition you calculated above in the disklabel.
|
|
In the example disklabel above, the offset is 38178 sectors of 512 bytes.
|
|
Therfore, the
|
|
.Xr dd 1
|
|
command would be something like:
|
|
.(disp
|
|
.No # Ic "gunzip miniroot.fs.gz"
|
|
.No # Ic "dd if=miniroot.fs of=/dev/rdsk/IDs0 seek=38178b"
|
|
.disp)
|
|
Note the
|
|
.Sq Li b
|
|
after the offset, which specifies blocks of 512 bytes.
|
|
.Pp
|
|
By dumping the miniroot to disk where the swap partition will be, you're
|
|
saving a step later where
|
|
.Pa SYS_INST
|
|
tries to download the miniroot over NFS.
|
|
Just make sure that when you enter the partition table into
|
|
.Pa SYS_INST
|
|
you use the same block offset for the swap partition as you dumped the
|
|
miniroot.
|
|
.
|
|
.Ss2 Configuring the netboot server
|
|
.
|
|
This step will configure your netboot server to provide
|
|
.Pa SYS_UBOOT
|
|
and the miniroot installer to your \*M.
|
|
.Pp
|
|
.so ../common/netboot
|
|
.
|
|
.Ss2 Put Series 400 systems in "HP-UX Compatible Boot Mode"
|
|
.
|
|
Series 400 systems can be configured to boot either
|
|
.Tn HP-UX
|
|
or
|
|
.Tn DomainOS .
|
|
To boot
|
|
.Nx*M
|
|
you must have your system configured in
|
|
.Sq Li "HP-UX Compatible Boot Mode" .
|
|
If, when you power on your machine, it does
|
|
.Em not
|
|
present a menu like the following, then you need to change your
|
|
configuration.
|
|
.(disp
|
|
Copyright 1990,
|
|
Hewlett-Packard Company.
|
|
All Rights Reserved.
|
|
|
|
BOOTROM Series 400 Rev. 1.1
|
|
MD12 REV 1.2 1990/08/07.14:27:08
|
|
[...]
|
|
.disp)
|
|
.(enum
|
|
Attach a Domain keyboard or an HIL keyboard.
|
|
.br
|
|
The BootROM knows how to use either, even if
|
|
.Nx
|
|
doesn't yet.
|
|
.It
|
|
Put your system into
|
|
.Sq "service mode" .
|
|
.br
|
|
For a 4XXs, there's a toggle switch on the back of the machine (near the top).
|
|
For a 4XXt or 4XXdl, press the green button on the front, behind
|
|
the silly door.
|
|
For a 425e, there's a toggle switch on the back of the
|
|
machine (in the middle).
|
|
The second green LED should light up.
|
|
.It
|
|
Reset the machine.
|
|
.br
|
|
Press the reset button.
|
|
For a 4XXs, ther's a small plunger on the back of
|
|
the machine (near the top).
|
|
For a 4XXt or 4XXdl, there's a white button
|
|
on the front, behind the silly door.
|
|
For a 425e, there's a button on the
|
|
back of the machine.
|
|
.It
|
|
Press
|
|
.Key RETURN
|
|
to get the Domain boot prompt
|
|
.No ( Li \*> No ) .
|
|
.br
|
|
You can type
|
|
.Key H
|
|
to get a list of available commands.
|
|
.It
|
|
Type the following sequence of commands to convert to
|
|
.Sq Li "HP-UX Compatible Boot Mode" .
|
|
.br
|
|
.(disp
|
|
.No "\*>" Ic "CF"
|
|
.No "Type [key] RETURN ?" Ic 2
|
|
.No "Type [key] RETURN ?" Ic 2
|
|
.No "Type T or P RETURN ?" Ic P
|
|
.No "Type [key] RETURN ?" Ic E
|
|
.disp)
|
|
.It
|
|
Be sure to turn
|
|
.Sq "service mode"
|
|
.Em off
|
|
when you're done.
|
|
It may prevent you from selecting which device to boot from.
|
|
.enum)
|
|
See the FAQ for additional help.
|
|
.Lk http://www.NetBSD.org/Ports/hp300/faq.html#domain
|
|
.
|
|
.Ss2 Searching for a bootable system
|
|
.
|
|
All the early hp300 Boot ROMs are very primitive and only allow a few
|
|
simple operations.
|
|
You can only interact with it after it is first powered on.
|
|
If you reboot the machine, it will ignore anything you type and
|
|
start loading the same OS you previously booted.
|
|
.Pp
|
|
At any time after it recognizes the keyboard, while it is doing its self
|
|
test or searching for a bootable system, you can hit reset to return it to
|
|
a cold-boot configuration.
|
|
On HIL keybaords, this is
|
|
.Key control-shift-break ,
|
|
where
|
|
.Key break
|
|
is the key in the upper left (where
|
|
escape is on sane keyboards).
|
|
There is no equivalent over serial terminal,
|
|
you'll need to power-cycle your machine.
|
|
.Pp
|
|
After it beeps (i.e. recognizes the HIL keyboard), press
|
|
.Key RETURN
|
|
twice to get the list of bootable devices.
|
|
.(disp
|
|
SEARCHING FOR A SYSTEM (RETURN To Pause)
|
|
.disp)
|
|
.Pp
|
|
The newer HP Boot ROM, present on Series 400 machines and some of the
|
|
later 300s (345, 375, 380, 382, 385) is capable of a little bit more.
|
|
To select which device to boot from, press
|
|
.Key RETURN
|
|
once after it beeps twice (i.e. recognizes the HIL keyboard) to get the
|
|
list of bootable devices.
|
|
.(disp
|
|
RESET To Power-Up, SPACE clears input Select System, type RETURN ?
|
|
.disp)
|
|
.Pp
|
|
The FAQ lists additional things you can do with the BootROM and describes
|
|
the order the BootROM looks for bootable devices.
|
|
.Lk http://www.NetBSD.org/Ports/hp300/faq.html
|
|
.Pp
|
|
A normal power-on sequence (from a 400s) looks something like this:
|
|
.(disp
|
|
Copyright 1990,
|
|
Hewlett-Packard Company.
|
|
All Rights Reserved.
|
|
|
|
BOOTROM Series 400 Rev. 1.1
|
|
MD12 REV 1.2 1990/08/07.14:27:08
|
|
MC68030 Processor
|
|
MC68882 Coprocessor
|
|
Configuration EEPROM
|
|
Utility Chip at 41
|
|
HP-HIL.Keyboard
|
|
RESET To Power-Up
|
|
Loading Memory
|
|
Self-Test Mode
|
|
RESET To Power-Up, SPACE clears input
|
|
Select System, type RETURN
|
|
HP-IB
|
|
DMA-C0
|
|
Self-Test Mode
|
|
RAM 33554158 Bytes
|
|
HP98644 (RS-232) at 9
|
|
HP PARALLEL at 12
|
|
HP98265 (SCSI S 32) at 14
|
|
HP98643 (LAN) at 21, AUI, 080009115DB3
|
|
Bit Mapped Video at 133 (Console)
|
|
System Search Mode
|
|
:RODIME RO3000T, 1406, 0
|
|
1Z SYS_UBOOT
|
|
:LAN080009115DB3, 2100, 0
|
|
2Z SYS_UBOOT
|
|
:HP7959, 702, 0, 0
|
|
1H SYSHPUX
|
|
1D SYSDEBUG
|
|
1B SYSBCKUP
|
|
:HP9122, 0700, 0, 0
|
|
3Z SYS_INST
|
|
.disp)
|
|
.Pp
|
|
You should see your bootstrap program somewhere in this list.
|
|
If it's not here, then your \*M can't boot it and there's a problem somewhere.
|
|
To boot from a particular device, type in the two character name for it
|
|
and press
|
|
.Key RETURN .
|
|
In this example, you'd type
|
|
.Key 2Z
|
|
to boot from the network.
|
|
.
|
|
.Ss2 Selecting ethernet port on Series 400
|
|
.
|
|
Series 400 machines have two ethernet media types built into the
|
|
motherboard.
|
|
You may only use one at a time.
|
|
When your Series 400 workstation goes through the self-test when
|
|
powered on or rebooted, it will say one of the following:
|
|
.(disp
|
|
HP98643 (LAN) at 21, AUI
|
|
HP98643 (LAN) at 21, Thin
|
|
.disp)
|
|
.Pp
|
|
If the wrong type of network is selected, you will need to change the
|
|
ethernet port.
|
|
You will need to open the case (4XXt, 4XXdl, 4XXe) or
|
|
remove the motherboard (4XXs) to access the jumper.
|
|
Be sure to use static-prevention measures, as you could easily fry
|
|
your motherboard from carelessness.
|
|
If you are uncomfortable with this, ask a friend who is
|
|
aware of these issues.
|
|
There is a block of 8 jumpers at the rear of the
|
|
motherboard, labeled AUI/Thin.
|
|
You will need to put the jumpers in the
|
|
position necessary for your type of ethernet.
|
|
.
|
|
.Ss2 Running SYS_INST
|
|
.
|
|
This step is necessary
|
|
.Em only
|
|
if you cannot netboot.
|
|
.Pp
|
|
Chose
|
|
.Li SYS_INST
|
|
from the list of bootable devices that the BootROM found.
|
|
.Li SYS_INST
|
|
will load and prompt you for a command.
|
|
.Pp
|
|
.Em A quick note about disk numbers:
|
|
While in the
|
|
.Pa SYS_INST
|
|
program, you may use different unit numbers for the disks than when the
|
|
.Nx
|
|
kernel is running.
|
|
The unit number for a disk while in
|
|
.Pa SYS_INST
|
|
is calculated with the following formula:
|
|
.Pp
|
|
.(disp
|
|
unit = (controller * 8) + slaveID
|
|
.disp)
|
|
.Pp
|
|
Controllers are numbered 0, 1, ... starting with the lowest select code.
|
|
SCSI controllers and HP-IB controllers are counted separately.
|
|
Therefore,
|
|
if you had a system with an internal HP-IB interface at select code 7,
|
|
a fast HP-IB interface at select code 14, and a SCSI interface at select
|
|
code 16, unit numbers might be something like the following:
|
|
.Bl -column -offset indent HP-IB\ at\ 14,\ slaveID\ 5 Unit (disk:\ rd13)
|
|
.It Sy Location Ta Sy Unit
|
|
.It HP-IB\ at\ 7,\ slaveID\ 2 Ta 2 Ta (disk:\ rd2)
|
|
.It HP-IB\ at\ 14,\ slaveID\ 5 Ta 13 Ta (disk:\ rd13)
|
|
.It SCSI\ at\ 16,\ slaveID\ 0 Ta 0 Ta (disk:\ sd0)
|
|
.El
|
|
.Pp
|
|
You will need to place a disklabel on the disk.
|
|
.Pp
|
|
.(disp
|
|
.No "sys_inst\*>" Ic disklabel
|
|
.disp)
|
|
.(Note
|
|
It may be worth selecting the
|
|
.Sy zap
|
|
option initially to ensure that
|
|
the disklabel area is clear.
|
|
This may be especially important if an
|
|
HP-UX boot block had been previously installed on the disk.
|
|
.Note)
|
|
.Pp
|
|
Select the
|
|
.Sy edit
|
|
option, and answer the questions about your disk.
|
|
There may be several questions which you may not be sure of the answers to.
|
|
Listed below are guidelines for SCSI and HP-IB disks:
|
|
.Pp
|
|
.Bl -column -offset indent -compact Track-to-track?xx xxxxx
|
|
.It Bad\ sectoring? Ta NO
|
|
.It Ecc? Ta NO
|
|
.It Interleave? Ta 1
|
|
.It Trackskew? Ta 0
|
|
.It Cylinderskew? Ta 0
|
|
.It Headswitch? Ta 0
|
|
.It Track-to-track? Ta 0
|
|
.It Drivedata\ 0-4? Ta 0\ (for\ all\ Drivedata\ values)
|
|
.El
|
|
.Pp
|
|
Next, you will be asked to fill out the partition map.
|
|
You must provide responses for all 8 partitions.
|
|
Remember, you must have the sector offset for the
|
|
.Sq Li b
|
|
partition match the location you dumped the miniroot file system image.
|
|
Set the size and
|
|
offset of any unused partition to 0.
|
|
Note that sizes and offsets are expressed in
|
|
.Sq n sectors ,
|
|
assuming 512 byte sectors.
|
|
Care should be taken
|
|
to ensure that partitions begin and end on cylinder boundaries (i.e. size
|
|
and offset is an even multiple of the number of sectors per cylinder).
|
|
While this is not technically necessary, it is generally encouraged.
|
|
.Pp
|
|
.(Note
|
|
When setting the partition type of the
|
|
.Sq Li b
|
|
partition, make sure to
|
|
specify it as an
|
|
.Li ffs
|
|
partition so that the miniroot can be mounted (even
|
|
if this will be a swap partition).
|
|
You will be given a chance to clean
|
|
this up later in the installation process.
|
|
.Note)
|
|
.Pp
|
|
Once you have edited the label, select the
|
|
.Sy show
|
|
option to verify that it is correct.
|
|
If so, select
|
|
.Sy write
|
|
and
|
|
.Sy done .
|
|
Otherwise, you may re-edit the label.
|
|
.Pp
|
|
In an earlier step, we already copied the miniroot image to the target
|
|
disk.
|
|
.Pp
|
|
Boot from the miniroot file system.
|
|
.Pp
|
|
.(disp
|
|
.No "sys_inst\*>" Ic boot
|
|
.disp)
|
|
.Pp
|
|
Enter the disk from which to boot.
|
|
The kernel in the miniroot file system will be booted into single-user mode.
|
|
.
|
|
.Ss2 Chosing a kernel location
|
|
.
|
|
Once the bootstrap program
|
|
.Li SYS_UBOOT
|
|
has started, it will pause and let you chose a kernel location, name, and
|
|
options:
|
|
.(disp
|
|
\*>\*> NetBSD/hp300 Primary Boot, Revision 1.13
|
|
\*>\*> (gregm@mcgarry, Mon Apr 15 08:46:32 NZST 2002)
|
|
\*>\*> HP 9000/425e SPU
|
|
\*>\*> Enter "reset" to reset system.
|
|
Boot: [[[le0a:]netbsd][-a][-c][-d][-s][-v][-q]] :-
|
|
.disp)
|
|
.Pp
|
|
If your kernel is on a different device than
|
|
.Li SYS_UBOOT
|
|
then you will need to type in where to find it.
|
|
This is the case, for
|
|
example, if your model is incapable of netbooting and you started
|
|
.Li SYS_UBOOT
|
|
from a floppy, and the miniroot installer is on a netboot server.
|
|
In this case, you'd type in
|
|
.Sq Li le0
|
|
at the prompt.
|
|
.Pp
|
|
If you've installed the miniroot on your disk, you can always boot from
|
|
that by using partition
|
|
.Sq Li b
|
|
when prompted by
|
|
.Li SYS_UBOOT .
|
|
For example, to boot the miniroot from an HP-IB disk on controller 0 at
|
|
slave ID 2, you'd type:
|
|
.(disp
|
|
.No "Boot: [[[rd0a:]netbsd][-a][-c][-d][-s][-v][-q]] :- " Ic "rd2b:netbsd"
|
|
.disp)
|