544 lines
18 KiB
Plaintext
544 lines
18 KiB
Plaintext
# $NetBSD: GENERIC,v 1.90 1999/10/04 19:02:55 hubertf Exp $
|
|
|
|
include "arch/sparc/conf/std.sparc"
|
|
|
|
maxusers 32
|
|
|
|
## System kernel configuration. See options(4) for more detail.
|
|
|
|
|
|
# Options for variants of the Sun SPARC architecure.
|
|
# We currently support three architecture types; at least one is required.
|
|
options SUN4 # sun4/100, sun4/200, sun4/300
|
|
options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc.
|
|
options SUN4M # sun4m - SS10, SS20, Classic, etc.
|
|
|
|
#options SUN4_MMU3L # 3-level MMU on sun4/400; (incomplete)
|
|
|
|
## System options specific to the sparc machine type
|
|
|
|
# Blink the power LED on some machines to indicate the system load.
|
|
#options BLINK
|
|
|
|
## Use a faster console than the PROM's slow drawing routines. Not needed
|
|
## for headless (no framebuffer) machines.
|
|
options RASTERCONSOLE # fast rasterop console
|
|
options FONT_GALLANT12x22 # the console font
|
|
#options FONT_BOLD8x16 # a somewhat smaller font
|
|
options RASTERCONSOLE_FGCOL=WSCOL_BLACK
|
|
options RASTERCONSOLE_BGCOL=WSCOL_WHITE
|
|
|
|
#### System options that are the same for all ports
|
|
|
|
## Root device configuration: change the ?'s if you are going to use a
|
|
## nonstandard root partition (other than where the kernel is booted from)
|
|
## and/or nonstandard root type (not ffs or nfs). Normally this can be
|
|
## automagically determined at boot time.
|
|
|
|
config netbsd root on ? type ?
|
|
|
|
## System call tracing (see ktrace(1)).
|
|
options KTRACE
|
|
|
|
## Collect statistics on kernel malloc's and free's. This does have a
|
|
## significant performance hit on slower machines, so it is intended for
|
|
## diagnostic use only.
|
|
#options KMEMSTATS
|
|
|
|
## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2))
|
|
options SYSVMSG # System V message queues
|
|
options SYSVSEM # System V semaphores
|
|
options SYSVSHM # System V shared memory
|
|
#options SHMMAXPGS=1024 # 1024 pages is the default
|
|
|
|
## Loadable kernel module support; still under development.
|
|
options LKM
|
|
|
|
## NFS boot options; default on sparc is the bootparam protocol
|
|
options NFS_BOOT_BOOTPARAM
|
|
#options NFS_BOOT_BOOTP
|
|
#options NFS_BOOT_DHCP
|
|
|
|
#### Debugging options
|
|
|
|
## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at
|
|
## serial console break or keyboard reset, where the PROM would normally
|
|
## intercept. DDB_HISTORY_SIZE adds up/down arrow command history.
|
|
#options DDB # kernel dynamic debugger
|
|
#options DDB_HISTORY_SIZE=100 # enable history editing in DDB
|
|
#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic'
|
|
|
|
## You may also use gdb, on another computer connected to this machine over
|
|
## a serial port. Both KGDBDEV and KGDBRATE should be specified; KGDBDEV is
|
|
## a dev_t encoded device number of the serial port to use.
|
|
## (0xc01 = ttya, 0xc02 = ttyb.)
|
|
#options KGDB # support for kernel gdb
|
|
#options KGDBDEV=0xc01 # kgdb device number (this sample is `ttyb')
|
|
#options KGDBRATE=38400 # baud rate
|
|
|
|
|
|
## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file),
|
|
## such that gdb(1) can be used on a kernel coredump.
|
|
|
|
#makeoptions DEBUG="-g"
|
|
|
|
|
|
## Adds code to the kernel that does internal consistency checks, and will
|
|
## cause the kernel to panic if corruption of internal data structures
|
|
## is detected.
|
|
#options DIAGNOSTIC # extra kernel sanity checking
|
|
|
|
## Enable (possibly expensive) debugging code that may also display messages
|
|
## on the system console
|
|
#options DEBUG
|
|
|
|
## Make SCSI error messages more verbose when explaining their meanings.
|
|
options SCSIVERBOSE
|
|
|
|
## `INSECURE' turns off the kernel security level (securelevel = 0 always).
|
|
## This allows writing to /dev/mem, loading kernel modules while multi-user,
|
|
## and other insecurities good only for development work. Do not use this
|
|
## option on a production machine.
|
|
#options INSECURE
|
|
|
|
## Allow non-root users to grab /dev/console with programs such as xconsole.
|
|
## `xconsole' therefore does not need setuid root with this option enabled.
|
|
#options UCONSOLE
|
|
|
|
## `FDSCRIPTS' allows non-readable but executable scripts by providing a
|
|
## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS',
|
|
## which implies FDSCRIPTS, allows scripts to be set-user-id using the same
|
|
## opaque file mechanism. Perl calls this "secure setuid scripts."
|
|
|
|
#options FDSCRIPTS
|
|
#options SETUIDSCRIPTS
|
|
|
|
## Options for compatibility with previous releases foreign system binaries.
|
|
## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up
|
|
## additional user-level utilities or system configuration files. See
|
|
## compat_sunos(8) and compat_svr4(8).
|
|
|
|
options COMPAT_43 # 4.3BSD system interfaces
|
|
options COMPAT_10 # NetBSD 1.0 binary compatibility
|
|
options COMPAT_11 # NetBSD 1.1 binary compatibility
|
|
options COMPAT_12 # NetBSD 1.2 binary compatibility
|
|
options COMPAT_13 # NetBSD 1.3 binary compatibility
|
|
options COMPAT_14 # NetBSD 1.4 binary compatibility
|
|
options COMPAT_SUNOS # SunOS 4.x binary compatibility
|
|
options COMPAT_SVR4 # SunOS 5.x binary compatibility
|
|
options COMPAT_AOUT # NetBSD a.out compatibility
|
|
|
|
## File systems. You probably need at least one of FFS or NFS.
|
|
file-system FFS # Berkeley Fast Filesystem
|
|
file-system NFS # Sun NFS-compatible filesystem client
|
|
file-system KERNFS # kernel data-structure filesystem
|
|
file-system NULLFS # NULL layered filesystem
|
|
file-system MFS # memory-based filesystem
|
|
file-system FDESC # user file descriptor filesystem
|
|
file-system UMAPFS # uid/gid remapping filesystem
|
|
file-system LFS # Log-based filesystem (still experimental)
|
|
file-system PORTAL # portal filesystem (still experimental)
|
|
file-system PROCFS # /proc
|
|
file-system CD9660 # ISO 9660 + Rock Ridge file system
|
|
file-system UNION # union file system
|
|
file-system MSDOSFS # MS-DOS FAT filesystem(s).
|
|
|
|
## File system options.
|
|
options NFSSERVER # Sun NFS-compatible filesystem server
|
|
options QUOTA # FFS quotas
|
|
#options FFS_EI # FFS Endian Independent support
|
|
|
|
## Network protocol support. In most environments, INET is required.
|
|
options INET # IP (Internet Protocol) v4
|
|
options TCP_COMPAT_42 # 4.2BSD IP implementation compatibility
|
|
#options GATEWAY # packet forwarding ("router switch")
|
|
#options MROUTING # packet forwarding of multicast packets
|
|
#options DIRECTED_BROADCAST # allow broadcasts through routers
|
|
options NS # Xerox NS networking
|
|
#options NSIP # Xerox NS tunneling over IP
|
|
options ISO,TPIP # OSI networking
|
|
options EON # OSI tunneling over IP
|
|
#options CCITT,LLC,HDLC # X.25 packet switched protocol
|
|
#options NETATALK # AppleTalk (over Ethernet) protocol
|
|
options NTP # Network Time Protocol in-kernel support
|
|
#options PPS_SYNC # Add serial line synchronization for NTP
|
|
options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs.
|
|
options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device
|
|
options PPP_BSDCOMP # Add BSD compression to ppp device
|
|
options PPP_DEFLATE # Add deflate (libz) compression to ppp device
|
|
options PPP_FILTER # Add active filters for ppp (via bpf)
|
|
|
|
|
|
|
|
#### Main bus and CPU .. all systems.
|
|
mainbus0 at root
|
|
cpu0 at mainbus0
|
|
|
|
#### Bus types found on SPARC systems.
|
|
|
|
sbus0 at mainbus0 # sun4c
|
|
obio0 at mainbus0 # sun4 and sun4m
|
|
sparcvme0 at mainbus0 # sun4
|
|
iommu0 at mainbus0 # sun4m
|
|
sbus0 at iommu0 # sun4m
|
|
sparcvme0 at iommu0 # sun4m
|
|
vme0 at sparcvme0 # mi VME attachment
|
|
|
|
## SBus expander box
|
|
xbox* at sbus? slot ? offset ?
|
|
sbus* at xbox?
|
|
|
|
## SBus to PCMCIA bridge
|
|
# Currently enabling nell* with audioamd* causes panic at attach
|
|
#nell* at sbus? slot ? offset ? # PCMCIA bridge
|
|
#pcmcia* at nell?
|
|
|
|
#### Standard system devices -- all required for a given architecture
|
|
|
|
## Auxiliary system registers on sun4c and sun4m
|
|
auxreg0 at mainbus0 # sun4c
|
|
auxreg0 at obio0 # sun4m
|
|
|
|
## Power status and control register on Sun4m systems
|
|
power0 at obio0
|
|
|
|
## Mostek clock found on 4/300, sun4c, and sun4m systems.
|
|
## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems.
|
|
clock0 at mainbus0 # sun4c
|
|
clock0 at obio0 # sun4m
|
|
clock0 at obio0 addr 0xf2000000 # sun4/300
|
|
|
|
## Intersil clock found on 4/100 and 4/200 systems.
|
|
oclock0 at obio0 addr 0xf3000000 # sun4/200
|
|
oclock0 at obio0 addr 0x03000000 # sun4/100
|
|
|
|
## Memory error registers.
|
|
memreg0 at mainbus0 # sun4c
|
|
memreg0 at obio0 # sun4m
|
|
memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300
|
|
memreg0 at obio0 addr 0x04000000 # sun4/100
|
|
|
|
## ECC memory control
|
|
eccmemctl0 at mainbus0 # sun4m
|
|
|
|
## Timer chip found on 4/300, sun4c, and sun4m systems.
|
|
timer0 at mainbus0 # sun4c
|
|
timer0 at obio0 # sun4m
|
|
timer0 at obio0 addr 0xef000000 # sun4/300
|
|
|
|
## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300
|
|
## doesn't use this driver; the `EEPROM' is in the NVRAM on the
|
|
## Mostek clock chip on 4/300 systems.
|
|
eeprom0 at obio0 addr 0xf2000000 # sun4/200
|
|
eeprom0 at obio0 addr 0x02000000 # sun4/100
|
|
|
|
|
|
#### Serial port configuration
|
|
|
|
## Zilog 8530 serial chips. Each has two-channels.
|
|
## zs0 is ttya and ttyb. zs1 is the keyboard and mouse.
|
|
zs0 at mainbus0 # sun4c
|
|
zs0 at obio0 # sun4m
|
|
zs0 at obio0 addr 0xf1000000 level 12 flags 0x103 # sun4/200 and sun4/300
|
|
zs0 at obio0 addr 0x01000000 level 12 flags 0x103 # sun4/100
|
|
zstty0 at zs0 channel 0 # ttya
|
|
zstty1 at zs0 channel 1 # ttyb
|
|
|
|
zs1 at mainbus0 # sun4c
|
|
zs1 at obio0 # sun4m
|
|
zs1 at obio0 addr 0xf0000000 level 12 flags 0x103 # sun4/200 and sun4/300
|
|
zs1 at obio0 addr 0x00000000 level 12 flags 0x103 # sun4/100
|
|
kbd0 at zs1 channel 0 # keyboard
|
|
ms0 at zs1 channel 1 # mouse
|
|
|
|
zs2 at obio0 addr 0xe0000000 level 12 flags 0x103 # sun4/300
|
|
zstty2 at zs2 channel 0 # ttyc
|
|
zstty3 at zs2 channel 1 # ttyd
|
|
|
|
|
|
## Magma Serial/Parallel driver
|
|
magma* at sbus? slot ? offset ?
|
|
mtty* at magma?
|
|
mbpp* at magma?
|
|
|
|
## PCMCIA serial interfaces
|
|
#com* at pcmcia?
|
|
#pcmcom* at pcmcia?
|
|
#com* at pcmcom?
|
|
|
|
#### Disk controllers and disks
|
|
|
|
#
|
|
|
|
## The following flags may be set for the NCR53c94 based esp driver:
|
|
## bits 0-7: disable disconnect/reselect for the corresponding target
|
|
## bits 8-15: disable synchronous negotiation for target [bit-8]
|
|
|
|
## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards.
|
|
## Both `dma' and `esp' are needed in all cases.
|
|
## Two kinds of additional SBus SCSI interfaces are available. One uses
|
|
## "esp at sbus" like the sun4c on-board; the other uses "esp at dma".
|
|
|
|
## sun4/300 SCSI - an NCR53c94 or equivalent behind
|
|
## an LSI Logic DMA controller
|
|
|
|
dma0 at obio0 addr 0xfa001000 level 4 # sun4/300
|
|
esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300
|
|
|
|
dma0 at sbus0 slot ? offset ? # sun4c/sun4m
|
|
esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c
|
|
esp0 at dma0 flags 0x0000 # sun4m
|
|
|
|
# FSBE/S SCSI
|
|
dma* at sbus? slot ? offset ? # SBus
|
|
esp* at sbus? slot ? offset ? flags 0x0000 # SBus (older proms)
|
|
esp* at dma? flags 0x0000 # SBus
|
|
|
|
scsibus* at esp?
|
|
|
|
## Qlogic ISP SBus SCSI Card
|
|
isp* at sbus? slot ? offset ?
|
|
scsibus* at isp?
|
|
|
|
## NCR5380-based "Sun SCSI 3" VME SCSI controller.
|
|
## This driver has several flags which may be enabled by OR'ing
|
|
## the values and using the "flags" directive.
|
|
## Valid flags are:
|
|
##
|
|
## 0x01 Use DMA (may be polled)
|
|
## 0x02 Use DMA completion interrupts
|
|
## 0x04 Allow disconnect/reselect
|
|
##
|
|
## E.g. the following would enable DMA, interrupts, and reselect:
|
|
## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07
|
|
##
|
|
## By default, DMA is enabled in the driver.
|
|
|
|
si0 at vme0 addr 0x200000 irq 2 vect 0x40
|
|
scsibus* at si?
|
|
|
|
## NCR5380-based "SCSI Weird" on-board SCSI interface found
|
|
## on sun4/100 systems. The flags are the same as the "si"
|
|
## controller. Note, while DMA is enabled by default, only
|
|
## polled DMA works at this time, and reselects do not work
|
|
## on this particular controller.
|
|
|
|
sw0 at obio0 addr 0x0a000000 level 3
|
|
scsibus* at sw?
|
|
|
|
## PCMCIA SCSI controllers
|
|
#aic* at pcmcia?
|
|
#scsibus* at aic?
|
|
|
|
|
|
## These entries find devices on all SCSI busses and assign
|
|
## unit numbers dynamically.
|
|
sd* at scsibus? target ? lun ? # SCSI disks
|
|
st* at scsibus? target ? lun ? # SCSI tapes
|
|
cd* at scsibus? target ? lun ? # SCSI CD-ROMs
|
|
ch* at scsibus? target ? lun ? # SCSI changer devices
|
|
ss* at scsibus? target ? lun ? # SCSI scanners
|
|
uk* at scsibus? target ? lun ? # unknown SCSI
|
|
|
|
|
|
## Xylogics 753 or 7053 VME SMD disk controllers and disks, found
|
|
## on sun4 systems.
|
|
xdc0 at vme0 addr 0xee80 irq 3 vect 0x44
|
|
xdc1 at vme0 addr 0xee90 irq 3 vect 0x45
|
|
xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46
|
|
xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47
|
|
xd* at xdc? drive ?
|
|
|
|
## Xylogics 451 or 451 VME SMD disk controllers and disks, found
|
|
## on sun4 systems.
|
|
xyc0 at vme0 addr 0xee40 irq 3 vect 0x48
|
|
xyc1 at vme0 addr 0xee48 irq 3 vect 0x49
|
|
xy* at xyc? drive ?
|
|
|
|
|
|
## Floppy controller and drive found on SPARCstations.
|
|
|
|
fdc0 at mainbus0 # sun4c controller
|
|
fdc0 at obio0 # sun4m controller
|
|
fd* at fdc0 # the drive itself
|
|
|
|
## PCMCIA IDE controllers
|
|
#wdc* at pcmcia?
|
|
#wd* at wdc?
|
|
|
|
## A disk-like interface to files. Can be used to create floppy, CD,
|
|
## miniroot images, etc.
|
|
|
|
pseudo-device vnd 4
|
|
|
|
## Concatenated and striped disks; with this, you can create a software-based
|
|
## disk array similar to a "RAID 0" setup. See ccd(4).
|
|
|
|
pseudo-device ccd 4
|
|
|
|
## RAIDframe disk driver: software RAID driver. See raid(4).
|
|
|
|
#pseudo-device raid 4
|
|
|
|
## Memory disk device, used on boot floppies with compressed
|
|
## kernel-plus-root-disk images.
|
|
|
|
#pseudo-device md 1
|
|
|
|
|
|
#### Network interfaces
|
|
|
|
## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue
|
|
## Three flavors of additional SBus ethernets are available. One attaches
|
|
## directly like the sun4c on-board, one uses the ledma device like the
|
|
## sun4m on-board, and one uses the lebuffer device.
|
|
|
|
le0 at obio0 addr 0xf9000000 level 6 # sun4/300
|
|
le0 at sbus0 slot ? offset ? # sun4c on-board
|
|
ledma0 at sbus0 slot ? offset ? # sun4m on-board
|
|
le0 at ledma0 # sun4m on-board
|
|
le* at sbus? slot ? offset ? # SBus
|
|
ledma* at sbus? slot ? offset ? # SBus
|
|
le* at ledma? # SBus
|
|
lebuffer0 at sbus? slot ? offset ? # SBus
|
|
le0 at lebuffer? # SBus
|
|
lebuffer* at sbus? slot ? offset ? # SBus
|
|
le* at lebuffer? # SBus
|
|
|
|
|
|
## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board
|
|
## or on a Multibus/VME card.
|
|
ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board
|
|
ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board
|
|
ie1 at vme0 addr 0xe88000 irq 3 vect 0x75 # VME
|
|
ie2 at vme0 addr 0x31ff02 irq 3 vect 0x76 # VME
|
|
ie3 at vme0 addr 0x35ff02 irq 3 vect 0x77 # VME
|
|
ie4 at vme0 addr 0x2dff02 irq 3 vect 0x7c # VME
|
|
|
|
## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet
|
|
## (qe, 10MBd) attached.
|
|
qec* at sbus? slot ? offset ? # Quad Ethernet Controller
|
|
be* at qec? # BigMac Ethernet (10/100MBd)
|
|
qe* at qec? # Mace Ethernet (10MBd)
|
|
|
|
## Happy Meal Ethernet (hme) (driver not quite ready yet)
|
|
#hme* at sbus? slot ? offset ?
|
|
|
|
# midway ATM
|
|
en0 at sbus? slot ? offset ?
|
|
|
|
# PCMCIA ethernet devices
|
|
#ep* at pcmcia?
|
|
#mbe* at pcmcia?
|
|
#ne* at pcmcia?
|
|
#sm* at pcmcia?
|
|
|
|
# MII/PHY support
|
|
exphy* at mii? phy ? # 3Com internal PHYs
|
|
icsphy* at mii? phy ? # Integrated Circuit Systems ICS1890
|
|
inphy* at mii? phy ? # Intel 82555 PHYs
|
|
lxtphy* at mii? phy ? # Level One LXT-970 PHYs
|
|
nsphy* at mii? phy ? # NS83840 PHYs
|
|
qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs
|
|
sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs
|
|
tlphy* at mii? phy ? # ThunderLAN PHYs
|
|
ukphy* at mii? phy ? # generic unknown PHYs
|
|
|
|
## Loopback network interface; required
|
|
pseudo-device loop
|
|
|
|
## SLIP and CSLIP interfaces, for IP over a serial line.
|
|
pseudo-device sl 2
|
|
|
|
## PPP, the successor to SLIP. See pppd(8).
|
|
pseudo-device ppp 2
|
|
|
|
## Starmode Radio IP, a special hardware network device.
|
|
#pseudo-device strip 1
|
|
|
|
## Network "tunnel" device, allowing protocol stacks to run in the userland.
|
|
## This is used by the third-party user-mode "ppp" program, and others.
|
|
pseudo-device tun 4
|
|
|
|
## Generic L3 over IP tunnel
|
|
#pseudo-device gre 2 # generic L3 over IP tunnel
|
|
|
|
## Berkeley Packet Filter, required to run RARPD. A generic C-language
|
|
## interface that allows selective examining of incoming packets.
|
|
pseudo-device bpfilter 8
|
|
|
|
## IP Filter, used in firewall and NAT applications. See ipnat(8) for
|
|
## one example of the use of the IP Filter.
|
|
pseudo-device ipfilter
|
|
|
|
|
|
#### Audio and video devices
|
|
|
|
## /dev/audio support (`audioamd' plus `audio')
|
|
##
|
|
audioamd0 at mainbus0 # sun4c
|
|
#audioamd0 at obio0 # sun4m
|
|
audioamd0 at sbus0 slot ? offset ? # sun4m
|
|
audio* at audioamd0
|
|
|
|
audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231
|
|
audio* at audiocs0
|
|
|
|
|
|
## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m
|
|
## systems. If your sun4 system has a cgfour installed in the P4 slot,
|
|
## the P4 entries for "bwtwo" will attach to the overlay plane of the
|
|
## "cgfour".
|
|
|
|
bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m
|
|
bwtwo* at sbus? slot ? offset ? #
|
|
bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200
|
|
bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot
|
|
bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot
|
|
|
|
## Sun "cgtwo" VME color framebuffer
|
|
cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8
|
|
|
|
## Sun "cgthree" Sbus color framebuffer
|
|
cgthree0 at sbus? slot ? offset ?
|
|
cgthree* at sbus? slot ? offset ?
|
|
#cgthree0 at obio? slot ? offset ? # sun4m
|
|
|
|
## Sun "cgfour" color framebuffer with overlay plane. See above comment
|
|
## regarding overlay plane.
|
|
cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4
|
|
cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4
|
|
|
|
## Sun "cgsix" accelerated color framebuffer.
|
|
cgsix0 at sbus? slot ? offset ?
|
|
cgsix* at sbus? slot ? offset ?
|
|
cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4
|
|
cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4
|
|
|
|
## Sun "cgeight" 24-bit framebuffer
|
|
cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4
|
|
cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4
|
|
|
|
## Sun "tcx" accelerated color framebuffer.
|
|
tcx0 at sbus? slot ? offset ?
|
|
tcx* at sbus? slot ? offset ?
|
|
|
|
# Sun "cgfourteen" accelerated 24-bit framebuffer.
|
|
cgfourteen0 at obio0 # sun4m
|
|
|
|
|
|
#### Other device configuration
|
|
|
|
## Pseudo ttys, required for network logins and programs like screen.
|
|
## 32 is a good number for average systems; you may have as many as you
|
|
## like, though 256 is more or less the upper limit. Increasing this
|
|
## number still requires you to run /dev/MAKEDEV to create the files
|
|
## for the ptys.
|
|
|
|
pseudo-device pty 32 # pseudo-ttys (for network, etc.)
|
|
|
|
## Random device, used to implement /dev/random (a source of random noise),
|
|
## and generate randomness for some kernel formulae.
|
|
|
|
pseudo-device rnd
|