235 lines
13 KiB
C
235 lines
13 KiB
C
/* $NetBSD: ihareg.h,v 1.6 2002/12/08 01:09:35 jmc Exp $ */
|
|
|
|
/*-
|
|
* Device driver for the INI-9XXXU/UW or INIC-940/950 PCI SCSI Controller.
|
|
*
|
|
* Written for 386bsd and FreeBSD by
|
|
* Winston Hung <winstonh@initio.com>
|
|
*
|
|
* Copyright (c) 1997-1999 Initio Corp.
|
|
* Copyright (c) 2000 Ken Westerback
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer,
|
|
* without modification, immediately at the beginning of the file.
|
|
* 2. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
* IN NO EVENT SHALL THE AUTHOR OR HIS RELATIVES BE LIABLE FOR ANY DIRECT,
|
|
* INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF MIND, USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
|
|
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
|
|
* THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
/*
|
|
* Ported to NetBSD by Izumi Tsutsui <tsutsui@ceres.dti.ne.jp> from OpenBSD:
|
|
* $OpenBSD: iha.h,v 1.2 2001/02/08 17:35:05 krw Exp $
|
|
*/
|
|
|
|
/*
|
|
* Tulip (aka inic-940/950) PCI Configuration Space Initio Specific Registers
|
|
*
|
|
* Offsets 0x00 through 0x3f are the standard PCI Configuration Header
|
|
* registers.
|
|
*
|
|
* Offsets 0x40 through 0x4f, 0x51, 0x53, 0x57, 0x5b, 0x5e and 0x5f are
|
|
* reserved registers.
|
|
*
|
|
* Registers 0x50 and 0x52 always read as 0.
|
|
*
|
|
* The register offset names and associated bit field names are taken
|
|
* from the Inic-950 Data Sheet, Version 2.1, March 1997
|
|
*/
|
|
#define TUL_GCTRL0 0x54 /* R/W Global Control 0 */
|
|
#define EEPRG 0x04 /* Enable EEPROM Programming */
|
|
#define TUL_GCTRL1 0x55 /* R/W Global Control 1 */
|
|
#define ATDEN 0x01 /* Auto Termination Detect Enable */
|
|
#define TUL_GSTAT 0x56 /* R/W Global Status - connector type */
|
|
#define TUL_EPAD0 0x58 /* R/W External EEPROM Addr (lo byte) */
|
|
#define TUL_EPAD1 0x59 /* R/W External EEPROM Addr (hi byte) */
|
|
#define TUL_PNVPG 0x5A /* R/W Data port to external BIOS */
|
|
#define TUL_EPDATA 0x5C /* R/W EEPROM Data port */
|
|
#define TUL_NVRAM 0x5D /* R/W Non-volatile RAM port */
|
|
#define READ 0x80 /* Read from given NVRAM addr */
|
|
#define WRITE 0x40 /* Write to given NVRAM addr */
|
|
#define ENABLE_ERASE 0x30 /* Enable NVRAM Erase/Write */
|
|
#define NVRCS 0x08 /* Select external NVRAM */
|
|
#define NVRCK 0x04 /* NVRAM Clock */
|
|
#define NVRDO 0x02 /* NVRAM Write Data */
|
|
#define NVRDI 0x01 /* NVRAM Read Data */
|
|
|
|
/*
|
|
* Tulip (aka inic-940/950) SCSI Registers
|
|
*/
|
|
#define TUL_STCNT0 0x80 /* R/W 24 bit SCSI Xfer Count */
|
|
#define TCNT 0x00ffffff /* SCSI Xfer Transfer Count */
|
|
#define TUL_SFIFOCNT 0x83 /* R/W 5 bit FIFO counter */
|
|
#define FIFOC 0x1f /* SCSI Offset Fifo Count */
|
|
#define TUL_SISTAT 0x84 /* R Interrupt Register */
|
|
#define RSELED 0x80 /* Reselected */
|
|
#define STIMEO 0x40 /* Selected/Reselected Timeout */
|
|
#define SBSRV 0x20 /* SCSI Bus Service */
|
|
#define SRSTD 0x10 /* SCSI Reset Detected */
|
|
#define DISCD 0x08 /* Disconnected Status */
|
|
#define SELED 0x04 /* Select Interrupt */
|
|
#define SCAMSCT 0x02 /* SCAM selected */
|
|
#define SCMDN 0x01 /* Command Complete */
|
|
#define TUL_SIEN 0x84 /* W Interrupt enable */
|
|
#define ALL_INTERRUPTS 0xff
|
|
#define TUL_STAT0 0x85 /* R Status 0 */
|
|
#define INTPD 0x80 /* Interrupt pending */
|
|
#define SQACT 0x40 /* Sequencer active */
|
|
#define XFCZ 0x20 /* Xfer counter zero */
|
|
#define SFEMP 0x10 /* FIFO empty */
|
|
#define SPERR 0x08 /* SCSI parity error */
|
|
#define PH_MASK 0x07 /* SCSI phase mask */
|
|
#define TUL_SCTRL0 0x85 /* W Control 0 */
|
|
#define RSSQC 0x20 /* Reset sequence counter */
|
|
#define RSFIFO 0x10 /* Flush FIFO */
|
|
#define CMDAB 0x04 /* Abort command (sequence) */
|
|
#define RSMOD 0x02 /* Reset SCSI Chip */
|
|
#define RSCSI 0x01 /* Reset SCSI Bus */
|
|
#define TUL_STAT1 0x86 /* R Status 1 */
|
|
#define STRCV 0x80 /* Status received */
|
|
#define MSGST 0x40 /* Message sent */
|
|
#define CPDNE 0x20 /* Data phase done */
|
|
#define DPHDN 0x10 /* Data phase done */
|
|
#define STSNT 0x08 /* Status sent */
|
|
#define SXCMP 0x04 /* Xfer completed */
|
|
#define SLCMP 0x02 /* Selection completed */
|
|
#define ARBCMP 0x01 /* Arbitration completed */
|
|
#define TUL_SCTRL1 0x86 /* W Control 1 */
|
|
#define ENSCAM 0x80 /* Enable SCAM */
|
|
#define NIDARB 0x40 /* No ID for Arbitration */
|
|
#define ENLRS 0x20 /* Low Level Reselect */
|
|
#define PWDN 0x10 /* Power down mode */
|
|
#define WCPU 0x08 /* Wide CPU */
|
|
#define EHRSL 0x04 /* Enable HW reselect */
|
|
#define ESBUSOUT 0x02 /* Enable SCSI data bus out latch */
|
|
#define ESBUSIN 0x01 /* Enable SCSI data bus in latch */
|
|
#define TUL_SSTATUS2 0x87 /* R Status 2 */
|
|
#define SABRT 0x80 /* Command aborted */
|
|
#define OSCZ 0x40 /* Offset counter zero */
|
|
#define SFFUL 0x20 /* FIFO full */
|
|
#define TMCZ 0x10 /* Timeout counter zero */
|
|
#define BSYGN 0x08 /* Busy release */
|
|
#define PHMIS 0x04 /* Phase mismatch */
|
|
#define SBEN 0x02 /* SCSI data bus enable */
|
|
#define SRST 0x01 /* SCSI bus reset in progress */
|
|
#define TUL_SCONFIG0 0x87 /* W Configuration */
|
|
#define PHLAT 0x80 /* Enable phase latch */
|
|
#define ITMOD 0x40 /* Initiator mode */
|
|
#define SPCHK 0x20 /* Enable SCSI parity */
|
|
#define ADMA8 0x10 /* Alternate dma 8-bits mode */
|
|
#define ADMAW 0x08 /* Alternate dma 16-bits mode */
|
|
#define EDACK 0x04 /* Enable DACK in wide SCSI xfer */
|
|
#define ALTPD 0x02 /* Alternate sync period mode */
|
|
#define DSRST 0x01 /* Disable SCSI Reset signal */
|
|
#define SCONFIG0DEFAULT (PHLAT | ITMOD | ALTPD | DSRST)
|
|
#define TUL_SOFSC 0x88 /* R Offset */
|
|
#define PERIOD_WIDE_SCSI 0x80 /* Enable Wide SCSI */
|
|
#define PERIOD_SYXPD 0x70 /* Synch. SCSI Xfer rate */
|
|
#define PERIOD_SYOFS 0x0f /* Synch. SCSI Offset */
|
|
#define TUL_SYNCM 0x88 /* W Sync. Xfer Period & Offset */
|
|
#define TUL_SBID 0x89 /* R SCSI BUS ID */
|
|
#define TUL_SID 0x89 /* W SCSI ID */
|
|
#define TUL_SALVC 0x8A /* R FIFO Avail Cnt/Identify Msg */
|
|
#define IHA_MSG_IDENTIFY_LUNMASK 0x07
|
|
#define TUL_STIMO 0x8A /* W Sel/Resel Time Out Register */
|
|
#define STIMO_250MS 153 /* in units of 1.6385us */
|
|
#define TUL_SDATI 0x8B /* R SCSI Bus contents */
|
|
#define TUL_SDAT0 0x8B /* W SCSI Data Out */
|
|
#define TUL_SFIFO 0x8C /* R/W FIFO */
|
|
#define TUL_SSIGI 0x90 /* R SCSI signal in */
|
|
#define REQ 0x80 /* REQ signal */
|
|
#define ACK 0x40 /* ACK signal */
|
|
#define BSY 0x20 /* BSY signal */
|
|
#define SEL 0x10 /* SEL signal */
|
|
#define ATN 0x08 /* ATN signal */
|
|
#define MSG 0x04 /* MSG signal */
|
|
#define CD 0x02 /* C/D signal */
|
|
#define IO 0x01 /* I/O signal */
|
|
#define TUL_SSIGO 0x90 /* W SCSI signal out */
|
|
#define TUL_SCMD 0x91 /* R/W SCSI Command */
|
|
#define NO_OP 0x00 /* Place Holder for tulip_wait() */
|
|
#define SEL_NOATN 0x01 /* Select w/o ATN Sequence */
|
|
#define XF_FIFO_OUT 0x03 /* FIFO Xfer Infomation out */
|
|
#define MSG_ACCEPT 0x0F /* Message Accept */
|
|
#define SEL_ATN 0x11 /* Select w ATN Sequence */
|
|
#define SEL_ATNSTOP 0x12 /* Select w ATN & Stop Sequence */
|
|
#define SELATNSTOP 0x1E /* Select w ATN & Stop Sequence */
|
|
#define SEL_ATN3 0x31 /* Select w ATN3 Sequence */
|
|
#define XF_DMA_OUT 0x43 /* DMA Xfer Infomation out */
|
|
#define EN_RESEL 0x80 /* Enable Reselection */
|
|
#define XF_FIFO_IN 0x83 /* FIFO Xfer Infomation in */
|
|
#define CMD_COMP 0x84 /* Command Complete Sequence */
|
|
#define XF_DMA_IN 0xC3 /* DMA Xfer Infomation in */
|
|
#define TUL_STEST0 0x92 /* R/W Test0 */
|
|
#define TUL_STEST1 0x93 /* R/W Test1 */
|
|
|
|
/*
|
|
* Tulip (aka inic-940/950) DMA Registers
|
|
*/
|
|
#define TUL_DXPA 0xC0 /* R/W DMA Xfer Physcl Addr 0-31*/
|
|
#define TUL_DXPAE 0xC4 /* R/W DMA Xfer Physcl Addr 32-63*/
|
|
#define TUL_DCXA 0xC8 /* R DMA Curr Xfer Physcl Addr 0-31*/
|
|
#define TUL_DCXAE 0xCC /* R DMA Curr Xfer Physcl Addr 32-63*/
|
|
#define TUL_DXC 0xD0 /* R/W DMA Xfer Counter */
|
|
#define TUL_DCXC 0xD4 /* R DMA Current Xfer Counter */
|
|
#define TUL_DCMD 0xD8 /* R/W DMA Command Register */
|
|
#define SGXFR 0x80 /* Scatter/Gather Xfer */
|
|
#define RSVD 0x40 /* Reserved - always reads as 0 */
|
|
#define XDIR 0x20 /* Xfer Direction 0/1 = out/in */
|
|
#define BMTST 0x10 /* Bus Master Test */
|
|
#define CLFIFO 0x08 /* Clear FIFO */
|
|
#define ABTXFR 0x04 /* Abort Xfer */
|
|
#define FRXFR 0x02 /* Force Xfer */
|
|
#define STRXFR 0x01 /* Start Xfer */
|
|
#define TUL_ISTUS0 0xDC /* R/W Interrupt Status Register */
|
|
#define DGINT 0x80 /* DMA Global Interrupt */
|
|
#define RSVRD0 0x40 /* Reserved */
|
|
#define RSVRD1 0x20 /* Reserved */
|
|
#define SCMP 0x10 /* SCSI Complete */
|
|
#define PXERR 0x08 /* PCI Xfer Error */
|
|
#define DABT 0x04 /* DMA Xfer Aborted */
|
|
#define FXCMP 0x02 /* Forced Xfer Complete */
|
|
#define XCMP 0x01 /* Bus Master Xfer Complete */
|
|
#define TUL_ISTUS1 0xDD /* R DMA status Register */
|
|
#define SCBSY 0x08 /* SCSI Busy */
|
|
#define FFULL 0x04 /* FIFO Full */
|
|
#define FEMPT 0x02 /* FIFO Empty */
|
|
#define XPEND 0x01 /* Xfer pending */
|
|
#define TUL_IMSK 0xE0 /* R/W Interrupt Mask Register */
|
|
#define MSCMP 0x10 /* Mask SCSI Complete */
|
|
#define MPXFER 0x08 /* Mask PCI Xfer Error */
|
|
#define MDABT 0x04 /* Mask Bus Master Abort */
|
|
#define MFCMP 0x02 /* Mask Force Xfer Complete */
|
|
#define MXCMP 0x01 /* Mask Bus Master Xfer Complete */
|
|
#define MASK_ALL (MXCMP | MFCMP | MDABT | MPXFER | MSCMP)
|
|
#define TUL_DCTRL0 0xE4 /* R/W DMA Control Register */
|
|
#define SXSTP 0x80 /* SCSI Xfer Stop */
|
|
#define RPMOD 0x40 /* Reset PCI Module */
|
|
#define RSVRD2 0x20 /* SCSI Xfer Stop */
|
|
#define PWDWN 0x10 /* Power Down */
|
|
#define ENTM 0x08 /* Enable SCSI Terminator Low */
|
|
#define ENTMW 0x04 /* Enable SCSI Terminator High */
|
|
#define DISAFC 0x02 /* Disable Auto Clear */
|
|
#define LEDCTL 0x01 /* LED Control */
|
|
#define TUL_DCTRL1 0xE5 /* R/W DMA Control Register 1 */
|
|
#define SDWS 0x01 /* SCSI DMA Wait State */
|
|
#define TUL_DFIFO 0xE8 /* R/W DMA FIFO */
|
|
|
|
#define TUL_WCTRL 0xF7 /* ?/? Bus master wait state control */
|
|
#define TUL_DCTRL 0xFB /* ?/? DMA delay control */
|