NetBSD/sys/arch/sparc/dev/zs.c

983 lines
22 KiB
C

/* $NetBSD: zs.c,v 1.85 2002/03/11 16:27:02 pk Exp $ */
/*-
* Copyright (c) 1996 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Gordon W. Ross.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the NetBSD
* Foundation, Inc. and its contributors.
* 4. Neither the name of The NetBSD Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Zilog Z8530 Dual UART driver (machine-dependent part)
*
* Runs two serial lines per chip using slave drivers.
* Plain tty/async lines use the zs_async slave.
* Sun keyboard/mouse uses the zs_kbd/zs_ms slaves.
*/
#include "opt_ddb.h"
#include "opt_kgdb.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/conf.h>
#include <sys/device.h>
#include <sys/file.h>
#include <sys/ioctl.h>
#include <sys/kernel.h>
#include <sys/proc.h>
#include <sys/tty.h>
#include <sys/time.h>
#include <sys/syslog.h>
#include <machine/bsd_openprom.h>
#include <machine/autoconf.h>
#include <machine/intr.h>
#include <machine/conf.h>
#include <machine/eeprom.h>
#include <machine/psl.h>
#include <machine/z8530var.h>
#include <dev/cons.h>
#include <dev/ic/z8530reg.h>
#include <sparc/sparc/vaddrs.h>
#include <sparc/sparc/auxreg.h>
#include <sparc/sparc/auxiotwo.h>
#include <sparc/dev/cons.h>
#include "kbd.h" /* NKBD */
#include "zs.h" /* NZS */
/* Make life easier for the initialized arrays here. */
#if NZS < 3
#undef NZS
#define NZS 3
#endif
/*
* Some warts needed by z8530tty.c -
* The default parity REALLY needs to be the same as the PROM uses,
* or you can not see messages done with printf during boot-up...
*/
int zs_def_cflag = (CREAD | CS8 | HUPCL);
int zs_major = 12;
/*
* The Sun provides a 4.9152 MHz clock to the ZS chips.
*/
#define PCLK (9600 * 512) /* PCLK pin input clock rate */
/*
* Select software interrupt bit based on TTY ipl.
*/
#if PIL_TTY == 1
# define IE_ZSSOFT IE_L1
#elif PIL_TTY == 4
# define IE_ZSSOFT IE_L4
#elif PIL_TTY == 6
# define IE_ZSSOFT IE_L6
#else
# error "no suitable software interrupt bit"
#endif
#define ZS_DELAY() (CPU_ISSUN4C ? (0) : delay(2))
/* The layout of this is hardware-dependent (padding, order). */
struct zschan {
volatile u_char zc_csr; /* ctrl,status, and indirect access */
u_char zc_xxx0;
volatile u_char zc_data; /* data */
u_char zc_xxx1;
};
struct zsdevice {
/* Yes, they are backwards. */
struct zschan zs_chan_b;
struct zschan zs_chan_a;
};
/* ZS channel used as the console device (if any) */
void *zs_conschan_get, *zs_conschan_put;
static u_char zs_init_reg[16] = {
0, /* 0: CMD (reset, etc.) */
0, /* 1: No interrupts yet. */
0, /* 2: IVECT */
ZSWR3_RX_8 | ZSWR3_RX_ENABLE,
ZSWR4_CLK_X16 | ZSWR4_ONESB | ZSWR4_EVENP,
ZSWR5_TX_8 | ZSWR5_TX_ENABLE,
0, /* 6: TXSYNC/SYNCLO */
0, /* 7: RXSYNC/SYNCHI */
0, /* 8: alias for data port */
ZSWR9_MASTER_IE | ZSWR9_NO_VECTOR,
0, /*10: Misc. TX/RX control bits */
ZSWR11_TXCLK_BAUD | ZSWR11_RXCLK_BAUD,
((PCLK/32)/9600)-2, /*12: BAUDLO (default=9600) */
0, /*13: BAUDHI (default=9600) */
ZSWR14_BAUD_ENA | ZSWR14_BAUD_FROM_PCLK,
ZSWR15_BREAK_IE,
};
/* Console ops */
static int zscngetc __P((dev_t));
static void zscnputc __P((dev_t, int));
static void zscnpollc __P((dev_t, int));
struct consdev zs_consdev = {
NULL,
NULL,
zscngetc,
zscnputc,
zscnpollc,
NULL,
};
/****************************************************************
* Autoconfig
****************************************************************/
/* Definition of the driver for autoconfig. */
static int zs_match_mainbus __P((struct device *, struct cfdata *, void *));
static int zs_match_obio __P((struct device *, struct cfdata *, void *));
static void zs_attach_mainbus __P((struct device *, struct device *, void *));
static void zs_attach_obio __P((struct device *, struct device *, void *));
static void zs_attach __P((struct zsc_softc *, struct zsdevice *, int));
static int zs_print __P((void *, const char *name));
struct cfattach zs_mainbus_ca = {
sizeof(struct zsc_softc), zs_match_mainbus, zs_attach_mainbus
};
struct cfattach zs_obio_ca = {
sizeof(struct zsc_softc), zs_match_obio, zs_attach_obio
};
extern struct cfdriver zs_cd;
/* Interrupt handlers. */
static int zshard __P((void *));
static int zssoft __P((void *));
static int zs_get_speed __P((struct zs_chanstate *));
/* Console device support */
static int zs_console_flags __P((int, int, int));
/* Power management hooks */
int zs_enable __P((struct zs_chanstate *));
void zs_disable __P((struct zs_chanstate *));
/*
* Is the zs chip present?
*/
static int
zs_match_mainbus(parent, cf, aux)
struct device *parent;
struct cfdata *cf;
void *aux;
{
struct mainbus_attach_args *ma = aux;
if (strcmp(cf->cf_driver->cd_name, ma->ma_name) != 0)
return (0);
return (1);
}
static int
zs_match_obio(parent, cf, aux)
struct device *parent;
struct cfdata *cf;
void *aux;
{
union obio_attach_args *uoba = aux;
struct obio4_attach_args *oba;
if (uoba->uoba_isobio4 == 0) {
struct sbus_attach_args *sa = &uoba->uoba_sbus;
if (strcmp(cf->cf_driver->cd_name, sa->sa_name) != 0)
return (0);
return (1);
}
oba = &uoba->uoba_oba4;
return (bus_space_probe(oba->oba_bustag, oba->oba_paddr,
1, 0, 0, NULL, NULL));
}
static void
zs_attach_mainbus(parent, self, aux)
struct device *parent;
struct device *self;
void *aux;
{
struct zsc_softc *zsc = (void *) self;
struct mainbus_attach_args *ma = aux;
zsc->zsc_bustag = ma->ma_bustag;
zsc->zsc_dmatag = ma->ma_dmatag;
zsc->zsc_promunit = PROM_getpropint(ma->ma_node, "slave", -2);
zsc->zsc_node = ma->ma_node;
/*
* For machines with zs on mainbus (all sun4c models), we expect
* the device registers to be mapped by the PROM.
*/
zs_attach(zsc, ma->ma_promvaddr, ma->ma_pri);
}
static void
zs_attach_obio(parent, self, aux)
struct device *parent;
struct device *self;
void *aux;
{
struct zsc_softc *zsc = (void *) self;
union obio_attach_args *uoba = aux;
if (uoba->uoba_isobio4 == 0) {
struct sbus_attach_args *sa = &uoba->uoba_sbus;
void *va;
struct zs_chanstate *cs;
int channel;
if (sa->sa_nintr == 0) {
printf(" no interrupt lines\n");
return;
}
/*
* Some sun4m models (Javastations) may not map the zs device.
*/
if (sa->sa_npromvaddrs > 0)
va = (void *)sa->sa_promvaddr;
else {
bus_space_handle_t bh;
if (sbus_bus_map(sa->sa_bustag,
sa->sa_slot,
sa->sa_offset,
sa->sa_size,
BUS_SPACE_MAP_LINEAR, &bh) != 0) {
printf(" cannot map zs registers\n");
return;
}
va = (void *)bh;
}
/*
* Check if power state can be set, e.g. Tadpole 3GX
*/
if (PROM_getpropint(sa->sa_node, "pwr-on-auxio2", 0))
{
printf (" powered via auxio2");
for (channel = 0; channel < 2; channel++) {
cs = &zsc->zsc_cs_store[channel];
cs->enable = zs_enable;
cs->disable = zs_disable;
}
}
zsc->zsc_bustag = sa->sa_bustag;
zsc->zsc_dmatag = sa->sa_dmatag;
zsc->zsc_promunit = PROM_getpropint(sa->sa_node, "slave", -2);
zsc->zsc_node = sa->sa_node;
zs_attach(zsc, va, sa->sa_pri);
} else {
struct obio4_attach_args *oba = &uoba->uoba_oba4;
bus_space_handle_t bh;
bus_addr_t paddr = oba->oba_paddr;
/*
* As for zs on mainbus, we require a PROM mapping.
*/
if (bus_space_map(oba->oba_bustag,
paddr,
sizeof(struct zsdevice),
BUS_SPACE_MAP_LINEAR | OBIO_BUS_MAP_USE_ROM,
&bh) != 0) {
printf(" cannot map zs registers\n");
return;
}
zsc->zsc_bustag = oba->oba_bustag;
zsc->zsc_dmatag = oba->oba_dmatag;
/* Find prom unit by physical address */
if (cpuinfo.cpu_type == CPUTYP_4_100)
/*
* On the sun4/100, the top-most 4 bits are zero
* on obio addresses; force them to 1's for the
* sake of the comparison here.
*/
paddr |= 0xf0000000;
zsc->zsc_promunit =
(paddr == 0xf1000000) ? 0 :
(paddr == 0xf0000000) ? 1 :
(paddr == 0xe0000000) ? 2 : -2;
zs_attach(zsc, (void *)bh, oba->oba_pri);
}
}
/*
* Attach a found zs.
*
* USE ROM PROPERTIES port-a-ignore-cd AND port-b-ignore-cd FOR
* SOFT CARRIER, AND keyboard PROPERTY FOR KEYBOARD/MOUSE?
*/
static void
zs_attach(zsc, zsd, pri)
struct zsc_softc *zsc;
struct zsdevice *zsd;
int pri;
{
struct zsc_attach_args zsc_args;
struct zs_chanstate *cs;
int s, channel;
static int didintr, prevpri;
if (zsd == NULL) {
printf("configuration incomplete\n");
return;
}
printf(" softpri %d\n", PIL_TTY);
/*
* Initialize software state for each channel.
*/
for (channel = 0; channel < 2; channel++) {
struct zschan *zc;
zsc_args.channel = channel;
cs = &zsc->zsc_cs_store[channel];
zsc->zsc_cs[channel] = cs;
cs->cs_channel = channel;
cs->cs_private = NULL;
cs->cs_ops = &zsops_null;
cs->cs_brg_clk = PCLK / 16;
zc = (channel == 0) ? &zsd->zs_chan_a : &zsd->zs_chan_b;
zsc_args.hwflags = zs_console_flags(zsc->zsc_promunit,
zsc->zsc_node,
channel);
if (zsc_args.hwflags & ZS_HWFLAG_CONSOLE) {
zsc_args.hwflags |= ZS_HWFLAG_USE_CONSDEV;
zsc_args.consdev = &zs_consdev;
}
if ((zsc_args.hwflags & ZS_HWFLAG_CONSOLE_INPUT) != 0) {
zs_conschan_get = zc;
}
if ((zsc_args.hwflags & ZS_HWFLAG_CONSOLE_OUTPUT) != 0) {
zs_conschan_put = zc;
}
/* Childs need to set cn_dev, etc */
cs->cs_reg_csr = &zc->zc_csr;
cs->cs_reg_data = &zc->zc_data;
bcopy(zs_init_reg, cs->cs_creg, 16);
bcopy(zs_init_reg, cs->cs_preg, 16);
/* XXX: Consult PROM properties for this?! */
cs->cs_defspeed = zs_get_speed(cs);
cs->cs_defcflag = zs_def_cflag;
/* Make these correspond to cs_defcflag (-crtscts) */
cs->cs_rr0_dcd = ZSRR0_DCD;
cs->cs_rr0_cts = 0;
cs->cs_wr5_dtr = ZSWR5_DTR | ZSWR5_RTS;
cs->cs_wr5_rts = 0;
/*
* Clear the master interrupt enable.
* The INTENA is common to both channels,
* so just do it on the A channel.
*/
if (channel == 0) {
zs_write_reg(cs, 9, 0);
}
/*
* Look for a child driver for this channel.
* The child attach will setup the hardware.
*/
if (!config_found(&zsc->zsc_dev, (void *)&zsc_args, zs_print)) {
/* No sub-driver. Just reset it. */
u_char reset = (channel == 0) ?
ZSWR9_A_RESET : ZSWR9_B_RESET;
s = splzs();
zs_write_reg(cs, 9, reset);
splx(s);
}
}
/*
* Now safe to install interrupt handlers. Note the arguments
* to the interrupt handlers aren't used. Note, we only do this
* once since both SCCs interrupt at the same level and vector.
*/
if (!didintr) {
didintr = 1;
prevpri = pri;
bus_intr_establish(zsc->zsc_bustag, pri, IPL_SERIAL, 0,
zshard, NULL);
bus_intr_establish(zsc->zsc_bustag, PIL_TTY,
IPL_SOFTSERIAL,
BUS_INTR_ESTABLISH_SOFTINTR,
zssoft, NULL);
} else if (pri != prevpri)
panic("broken zs interrupt scheme");
evcnt_attach_dynamic(&zsc->zsc_intrcnt, EVCNT_TYPE_INTR, NULL,
zsc->zsc_dev.dv_xname, "intr");
/*
* Set the master interrupt enable and interrupt vector.
* (common to both channels, do it on A)
*/
cs = zsc->zsc_cs[0];
s = splhigh();
/* interrupt vector */
zs_write_reg(cs, 2, zs_init_reg[2]);
/* master interrupt control (enable) */
zs_write_reg(cs, 9, zs_init_reg[9]);
splx(s);
#if 0
/*
* XXX: L1A hack - We would like to be able to break into
* the debugger during the rest of autoconfiguration, so
* lower interrupts just enough to let zs interrupts in.
* This is done after both zs devices are attached.
*/
if (zsc->zsc_promunit == 1) {
printf("zs1: enabling zs interrupts\n");
(void)splfd(); /* XXX: splzs - 1 */
}
#endif
}
static int
zs_print(aux, name)
void *aux;
const char *name;
{
struct zsc_attach_args *args = aux;
if (name != NULL)
printf("%s: ", name);
if (args->channel != -1)
printf(" channel %d", args->channel);
return (UNCONF);
}
static volatile int zssoftpending;
/*
* Our ZS chips all share a common, autovectored interrupt,
* so we have to look at all of them on each interrupt.
*/
static int
zshard(arg)
void *arg;
{
struct zsc_softc *zsc;
int unit, rr3, rval, softreq;
rval = softreq = 0;
for (unit = 0; unit < zs_cd.cd_ndevs; unit++) {
struct zs_chanstate *cs;
zsc = zs_cd.cd_devs[unit];
if (zsc == NULL)
continue;
rr3 = zsc_intr_hard(zsc);
/* Count up the interrupts. */
if (rr3) {
rval |= rr3;
zsc->zsc_intrcnt.ev_count++;
}
if ((cs = zsc->zsc_cs[0]) != NULL)
softreq |= cs->cs_softreq;
if ((cs = zsc->zsc_cs[1]) != NULL)
softreq |= cs->cs_softreq;
}
/* We are at splzs here, so no need to lock. */
if (softreq && (zssoftpending == 0)) {
zssoftpending = IE_ZSSOFT;
#if defined(SUN4M)
if (CPU_ISSUN4M)
raise(0, PIL_TTY);
else
#endif
ienab_bis(IE_ZSSOFT);
}
return (rval);
}
/*
* Similar scheme as for zshard (look at all of them)
*/
static int
zssoft(arg)
void *arg;
{
struct zsc_softc *zsc;
int s, unit;
/* This is not the only ISR on this IPL. */
if (zssoftpending == 0)
return (0);
/*
* The soft intr. bit will be set by zshard only if
* the variable zssoftpending is zero. The order of
* these next two statements prevents our clearing
* the soft intr bit just after zshard has set it.
*/
/* ienab_bic(IE_ZSSOFT); */
zssoftpending = 0;
/* Make sure we call the tty layer at spltty. */
s = spltty();
for (unit = 0; unit < zs_cd.cd_ndevs; unit++) {
zsc = zs_cd.cd_devs[unit];
if (zsc == NULL)
continue;
(void)zsc_intr_soft(zsc);
}
splx(s);
return (1);
}
/*
* Compute the current baud rate given a ZS channel.
*/
static int
zs_get_speed(cs)
struct zs_chanstate *cs;
{
int tconst;
tconst = zs_read_reg(cs, 12);
tconst |= zs_read_reg(cs, 13) << 8;
return (TCONST_TO_BPS(cs->cs_brg_clk, tconst));
}
/*
* MD functions for setting the baud rate and control modes.
*/
int
zs_set_speed(cs, bps)
struct zs_chanstate *cs;
int bps; /* bits per second */
{
int tconst, real_bps;
if (bps == 0)
return (0);
#ifdef DIAGNOSTIC
if (cs->cs_brg_clk == 0)
panic("zs_set_speed");
#endif
tconst = BPS_TO_TCONST(cs->cs_brg_clk, bps);
if (tconst < 0)
return (EINVAL);
/* Convert back to make sure we can do it. */
real_bps = TCONST_TO_BPS(cs->cs_brg_clk, tconst);
/* XXX - Allow some tolerance here? */
if (real_bps != bps)
return (EINVAL);
cs->cs_preg[12] = tconst;
cs->cs_preg[13] = tconst >> 8;
/* Caller will stuff the pending registers. */
return (0);
}
int
zs_set_modes(cs, cflag)
struct zs_chanstate *cs;
int cflag; /* bits per second */
{
int s;
/*
* Output hardware flow control on the chip is horrendous:
* if carrier detect drops, the receiver is disabled, and if
* CTS drops, the transmitter is stoped IN MID CHARACTER!
* Therefore, NEVER set the HFC bit, and instead use the
* status interrupt to detect CTS changes.
*/
s = splzs();
cs->cs_rr0_pps = 0;
if ((cflag & (CLOCAL | MDMBUF)) != 0) {
cs->cs_rr0_dcd = 0;
if ((cflag & MDMBUF) == 0)
cs->cs_rr0_pps = ZSRR0_DCD;
} else
cs->cs_rr0_dcd = ZSRR0_DCD;
if ((cflag & CRTSCTS) != 0) {
cs->cs_wr5_dtr = ZSWR5_DTR;
cs->cs_wr5_rts = ZSWR5_RTS;
cs->cs_rr0_cts = ZSRR0_CTS;
} else if ((cflag & CDTRCTS) != 0) {
cs->cs_wr5_dtr = 0;
cs->cs_wr5_rts = ZSWR5_DTR;
cs->cs_rr0_cts = ZSRR0_CTS;
} else if ((cflag & MDMBUF) != 0) {
cs->cs_wr5_dtr = 0;
cs->cs_wr5_rts = ZSWR5_DTR;
cs->cs_rr0_cts = ZSRR0_DCD;
} else {
cs->cs_wr5_dtr = ZSWR5_DTR | ZSWR5_RTS;
cs->cs_wr5_rts = 0;
cs->cs_rr0_cts = 0;
}
splx(s);
/* Caller will stuff the pending registers. */
return (0);
}
/*
* Read or write the chip with suitable delays.
*/
u_char
zs_read_reg(cs, reg)
struct zs_chanstate *cs;
u_char reg;
{
u_char val;
*cs->cs_reg_csr = reg;
ZS_DELAY();
val = *cs->cs_reg_csr;
ZS_DELAY();
return (val);
}
void
zs_write_reg(cs, reg, val)
struct zs_chanstate *cs;
u_char reg, val;
{
*cs->cs_reg_csr = reg;
ZS_DELAY();
*cs->cs_reg_csr = val;
ZS_DELAY();
}
u_char
zs_read_csr(cs)
struct zs_chanstate *cs;
{
u_char val;
val = *cs->cs_reg_csr;
ZS_DELAY();
return (val);
}
void
zs_write_csr(cs, val)
struct zs_chanstate *cs;
u_char val;
{
*cs->cs_reg_csr = val;
ZS_DELAY();
}
u_char
zs_read_data(cs)
struct zs_chanstate *cs;
{
u_char val;
val = *cs->cs_reg_data;
ZS_DELAY();
return (val);
}
void zs_write_data(cs, val)
struct zs_chanstate *cs;
u_char val;
{
*cs->cs_reg_data = val;
ZS_DELAY();
}
/****************************************************************
* Console support functions (Sun specific!)
* Note: this code is allowed to know about the layout of
* the chip registers, and uses that to keep things simple.
* XXX - I think I like the mvme167 code better. -gwr
****************************************************************/
/*
* Handle user request to enter kernel debugger.
*/
void
zs_abort(cs)
struct zs_chanstate *cs;
{
struct zschan *zc = zs_conschan_get;
int rr0;
/* Wait for end of break to avoid PROM abort. */
/* XXX - Limit the wait? */
do {
rr0 = zc->zc_csr;
ZS_DELAY();
} while (rr0 & ZSRR0_BREAK);
#if defined(KGDB)
zskgdb(cs);
#elif defined(DDB)
Debugger();
#else
printf("stopping on keyboard abort\n");
callrom();
#endif
}
int zs_getc __P((void *arg));
void zs_putc __P((void *arg, int c));
/*
* Polled input char.
*/
int
zs_getc(arg)
void *arg;
{
struct zschan *zc = arg;
int s, c, rr0;
s = splhigh();
/* Wait for a character to arrive. */
do {
rr0 = zc->zc_csr;
ZS_DELAY();
} while ((rr0 & ZSRR0_RX_READY) == 0);
c = zc->zc_data;
ZS_DELAY();
splx(s);
/*
* This is used by the kd driver to read scan codes,
* so don't translate '\r' ==> '\n' here...
*/
return (c);
}
/*
* Polled output char.
*/
void
zs_putc(arg, c)
void *arg;
int c;
{
struct zschan *zc = arg;
int s, rr0;
s = splhigh();
/* Wait for transmitter to become ready. */
do {
rr0 = zc->zc_csr;
ZS_DELAY();
} while ((rr0 & ZSRR0_TX_READY) == 0);
/*
* Send the next character.
* Now you'd think that this could be followed by a ZS_DELAY()
* just like all the other chip accesses, but it turns out that
* the `transmit-ready' interrupt isn't de-asserted until
* some period of time after the register write completes
* (more than a couple instructions). So to avoid stray
* interrupts we put in the 2us delay regardless of cpu model.
*/
zc->zc_data = c;
delay(2);
splx(s);
}
/*****************************************************************/
/*
* Polled console input putchar.
*/
int
zscngetc(dev)
dev_t dev;
{
return (zs_getc(zs_conschan_get));
}
/*
* Polled console output putchar.
*/
void
zscnputc(dev, c)
dev_t dev;
int c;
{
zs_putc(zs_conschan_put, c);
}
void
zscnpollc(dev, on)
dev_t dev;
int on;
{
/* No action needed */
}
int
zs_console_flags(promunit, node, channel)
int promunit;
int node;
int channel;
{
int cookie, flags = 0;
switch (prom_version()) {
case PROM_OLDMON:
case PROM_OBP_V0:
/*
* Use `promunit' and `channel' to derive the PROM
* stdio handles that correspond to this device.
*/
if (promunit == 0)
cookie = PROMDEV_TTYA + channel;
else if (promunit == 1 && channel == 0)
cookie = PROMDEV_KBD;
else
cookie = -1;
if (cookie == prom_stdin())
flags |= ZS_HWFLAG_CONSOLE_INPUT;
/*
* Prevent the keyboard from matching the output device
* (note that PROMDEV_KBD == PROMDEV_SCREEN == 0!).
*/
if (cookie != PROMDEV_KBD && cookie == prom_stdout())
flags |= ZS_HWFLAG_CONSOLE_OUTPUT;
break;
case PROM_OBP_V2:
case PROM_OBP_V3:
case PROM_OPENFIRM:
/*
* Match the nodes and device arguments prepared by
* consinit() against our device node and channel.
* (The device argument is the part of the OBP path
* following the colon, as in `/obio/zs@0,100000:a')
*/
/* Default to channel 0 if there are no explicit prom args */
cookie = 0;
if (node == prom_stdin_node) {
if (prom_stdin_args[0] != '\0')
/* Translate (a,b) -> (0,1) */
cookie = prom_stdin_args[0] - 'a';
if (channel == cookie)
flags |= ZS_HWFLAG_CONSOLE_INPUT;
}
if (node == prom_stdout_node) {
if (prom_stdout_args[0] != '\0')
/* Translate (a,b) -> (0,1) */
cookie = prom_stdout_args[0] - 'a';
if (channel == cookie)
flags |= ZS_HWFLAG_CONSOLE_OUTPUT;
}
break;
default:
break;
}
return (flags);
}
/*
* Power management hooks for zsopen() and zsclose().
* We use them to power on/off the ports, if necessary.
*/
int
zs_enable(cs)
struct zs_chanstate *cs;
{
auxiotwoserialendis (ZS_ENABLE);
cs->enabled = 1;
return(0);
}
void
zs_disable(cs)
struct zs_chanstate *cs;
{
auxiotwoserialendis (ZS_DISABLE);
cs->enabled = 0;
}