NetBSD/usr.sbin/named/man/mailaddr.7

138 lines
5.2 KiB
Groff

.\" $NetBSD: mailaddr.7,v 1.1 1996/02/02 15:27:34 mrg Exp $
.\"
.\" Copyright (c) 1983, 1987 The Regents of the University of California.
.\" All rights reserved.
.\"
.\" Redistribution and use in source and binary forms are permitted
.\" provided that the above copyright notice and this paragraph are
.\" duplicated in all such forms and that any documentation,
.\" advertising materials, and other materials related to such
.\" distribution and use acknowledge that the software was developed
.\" by the University of California, Berkeley. The name of the
.\" University may not be used to endorse or promote products derived
.\" from this software without specific prior written permission.
.\" THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
.\" IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
.\" WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
.\"
.\" @(#)mailaddr.7 6.5 (Berkeley) 2/14/89
.\"
.TH MAILADDR 7 "February 14, 1989"
.UC 5
.SH NAME
mailaddr \- mail addressing description
.SH DESCRIPTION
Mail addresses are based on the ARPANET protocol listed at the end of this
manual page. These addresses are in the general format
.PP
user@domain
.PP
where a domain is a hierarchical dot separated list of subdomains. For
example, the address
.PP
eric@monet.berkeley.edu
.PP
is normally interpreted from right to left: the message should go to the
ARPA name tables (which do not correspond exactly to the physical ARPANET),
then to the Berkeley gateway, after which it should go to the local host
monet. When the message reaches monet it is delivered to the user ``eric''.
.PP
Unlike some other forms of addressing, this does not imply any routing.
Thus, although this address is specified as an ARPA address, it might
travel by an alternate route if that were more convenient or efficient.
For example, at Berkeley, the associated message would probably go directly
to monet over the Ethernet rather than going via the Berkeley ARPANET
gateway.
.SS Abbreviation.
.PP
Under certain circumstances it may not be necessary to type the entire
domain name. In general, anything following the first dot may be omitted
if it is the same as the domain from which you are sending the message.
For example, a user on ``calder.berkeley.edu'' could send to ``eric@monet''
without adding the ``berkeley.edu'' since it is the same on both sending
and receiving hosts.
.PP
Certain other abbreviations may be permitted as special cases. For
example, at Berkeley, ARPANET hosts may be referenced without adding
the ``berkeley.edu'' as long as their names do not conflict with a local
host name.
.SS Compatibility.
.PP
Certain old address formats are converted to the new format to provide
compatibility with the previous mail system. In particular,
.PP
user@host.ARPA
.PP
is allowed and
.PP
host:user
.PP
is converted to
.PP
user@host
.PP
to be consistent with the \fIrcp\fP(1) command.
.PP
Also, the syntax
.PP
host!user
.PP
is converted to:
.PP
user@host.UUCP
.PP
This is normally converted back to the ``host!user'' form before being sent
on for compatibility with older UUCP hosts.
.PP
The current implementation is not able to route messages automatically through
the UUCP network. Until that time you must explicitly tell the mail system
which hosts to send your message through to get to your final destination.
.SS Case Distinctions.
.PP
Domain names (i.e., anything after the ``@'' sign) may be given in any mixture
of upper and lower case with the exception of UUCP hostnames. Most hosts
accept any combination of case in user names, with the notable exception of
MULTICS sites.
.SS Route-addrs.
.PP
Under some circumstances it may be necessary to route a message through
several hosts to get it to the final destination. Normally this routing
is done automatically, but sometimes it is desirable to route the message
manually. Addresses which show these relays are termed ``route-addrs.''
These use the syntax:
.PP
<@hosta,@hostb:user@hostc>
.PP
This specifies that the message should be sent to hosta, from there to hostb,
and finally to hostc. This path is forced even if there is a more efficient
path to hostc.
.PP
Route-addrs occur frequently on return addresses, since these are generally
augmented by the software at each host. It is generally possible to ignore
all but the ``user@domain'' part of the address to determine the actual
sender.
.SS Postmaster.
.PP
Every site is required to have a user or user alias designated ``postmaster''
to which problems with the mail system may be addressed.
.SS Other Networks.
.PP
Some other networks can be reached by giving the name of the network as the
last component of the domain. \fIThis is not a standard feature\fP and may
not be supported at all sites. For example, messages to CSNET or BITNET sites
can often be sent to ``user@host.CSNET'' or ``user@host.BITNET'' respectively.
.SH BUGS
The RFC822 group syntax (``group:user1,user2,user3;'') is not supported
except in the special case of ``group:;'' because of a conflict with old
berknet-style addresses.
.PP
Route-Address syntax is grotty.
.PP
UUCP- and ARPANET-style addresses do not coexist politely.
.SH SEE ALSO
mail(1), sendmail(8);
Crocker, D. H.,
.ul
Standard for the Format of Arpa Internet Text Messages,
RFC822.