/* $NetBSD: refclock_parse.c,v 1.3 2003/12/04 16:23:37 drochner Exp $ */ /* * /src/NTP/ntp-4/ntpd/refclock_parse.c,v 4.36 1999/11/28 17:18:20 kardel RELEASE_19991128_A * * refclock_parse.c,v 4.36 1999/11/28 17:18:20 kardel RELEASE_19991128_A * * generic reference clock driver for receivers * * optionally make use of a STREAMS module for input processing where * available and configured. Currently the STREAMS module * is only available for Suns running SunOS 4.x and SunOS5.x * * the STREAMS module is not required for operation and may be omitted * at the cost of reduced accuracy. As new kernel interfaces emerger this * restriction may be lifted in future. * * Copyright (c) 1995-1999 by Frank Kardel * Copyright (c) 1989-1994 by Frank Kardel, Friedrich-Alexander Universität Erlangen-Nürnberg, Germany * * This software may not be sold for profit without a written consent * from the author. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. * */ #ifdef HAVE_CONFIG_H # include #endif #if defined(REFCLOCK) && defined(CLOCK_PARSE) /* * This driver currently provides the support for * - Meinberg receiver DCF77 PZF 535 (TCXO version) (DCF) * - Meinberg receiver DCF77 PZF 535 (OCXO version) (DCF) * - Meinberg receiver DCF77 PZF 509 (DCF) * - Meinberg receiver DCF77 AM receivers (e.g. C51) (DCF) * - IGEL CLOCK (DCF) * - ELV DCF7000 (DCF) * - Schmid clock (DCF) * - Conrad DCF77 receiver module (DCF) * - FAU DCF77 NTP receiver (TimeBrick) (DCF) * * - Meinberg GPS166/GPS167 (GPS) * - Trimble (TSIP and TAIP protocol) (GPS) * * - RCC8000 MSF Receiver (MSF) * - WHARTON 400A Series clock (DCF) * - VARITEXT clock (MSF) */ /* * Meinberg receivers are usually connected via a * 9600 baud serial line * * The Meinberg GPS receivers also have a special NTP time stamp * format. The firmware release is Uni-Erlangen. * * Meinberg generic receiver setup: * output time code every second * Baud rate 9600 7E2S * * Meinberg GPS16x setup: * output time code every second * Baudrate 19200 8N1 * * This software supports the standard data formats used * in Meinberg receivers. * * Special software versions are only sensible for the * GPS 16x family of receivers. * * Meinberg can be reached via: http://www.meinberg.de/ */ #include "ntpd.h" #include "ntp_refclock.h" #include "ntp_unixtime.h" /* includes */ #include "ntp_control.h" #include #include #ifndef TM_IN_SYS_TIME # include #endif #if !defined(STREAM) && !defined(HAVE_SYSV_TTYS) && !defined(HAVE_BSD_TTYS) && !defined(HAVE_TERMIOS) # include "Bletch: Define one of {STREAM,HAVE_SYSV_TTYS,HAVE_TERMIOS}" #endif #ifdef STREAM # include # include #endif #ifdef HAVE_TERMIOS # define TTY_GETATTR(_FD_, _ARG_) tcgetattr((_FD_), (_ARG_)) # define TTY_SETATTR(_FD_, _ARG_) tcsetattr((_FD_), TCSANOW, (_ARG_)) # undef HAVE_SYSV_TTYS #endif #ifdef HAVE_SYSV_TTYS # define TTY_GETATTR(_FD_, _ARG_) ioctl((_FD_), TCGETA, (_ARG_)) # define TTY_SETATTR(_FD_, _ARG_) ioctl((_FD_), TCSETAW, (_ARG_)) #endif #ifdef HAVE_BSD_TTYS /* #error CURRENTLY NO BSD TTY SUPPORT */ # include "Bletch: BSD TTY not currently supported" #endif #ifdef HAVE_SYS_IOCTL_H # include #endif #ifdef PPS #ifdef HAVE_SYS_PPSCLOCK_H #include #endif #ifdef HAVE_TIO_SERIAL_STUFF #include #endif #endif #include "ntp_io.h" #include "ntp_stdlib.h" #include "parse.h" #include "mbg_gps166.h" #include "trimble.h" #include "binio.h" #include "ascii.h" #include "ieee754io.h" static char rcsid[]="refclock_parse.c,v 4.36 1999/11/28 17:18:20 kardel RELEASE_19991128_A"; /**=========================================================================== ** external interface to ntp mechanism **/ static void parse_init P((void)); static int parse_start P((int, struct peer *)); static void parse_shutdown P((int, struct peer *)); static void parse_poll P((int, struct peer *)); static void parse_control P((int, struct refclockstat *, struct refclockstat *, struct peer *)); #define parse_buginfo noentry struct refclock refclock_parse = { parse_start, parse_shutdown, parse_poll, parse_control, parse_init, parse_buginfo, NOFLAGS }; /* * Definitions */ #define MAXUNITS 4 /* maximum number of "PARSE" units permitted */ #define PARSEDEVICE "/dev/refclock-%d" /* device to open %d is unit number */ #undef ABS #define ABS(_X_) (((_X_) < 0) ? -(_X_) : (_X_)) /**=========================================================================== ** function vector for dynamically binding io handling mechanism **/ struct parseunit; /* to keep inquiring minds happy */ typedef struct bind { const char *bd_description; /* name of type of binding */ int (*bd_init) P((struct parseunit *)); /* initialize */ void (*bd_end) P((struct parseunit *)); /* end */ int (*bd_setcs) P((struct parseunit *, parsectl_t *)); /* set character size */ int (*bd_disable) P((struct parseunit *)); /* disable */ int (*bd_enable) P((struct parseunit *)); /* enable */ int (*bd_getfmt) P((struct parseunit *, parsectl_t *)); /* get format */ int (*bd_setfmt) P((struct parseunit *, parsectl_t *)); /* setfmt */ int (*bd_timecode) P((struct parseunit *, parsectl_t *)); /* get time code */ void (*bd_receive) P((struct recvbuf *)); /* receive operation */ int (*bd_io_input) P((struct recvbuf *)); /* input operation */ } bind_t; #define PARSE_END(_X_) (*(_X_)->binding->bd_end)(_X_) #define PARSE_SETCS(_X_, _CS_) (*(_X_)->binding->bd_setcs)(_X_, _CS_) #define PARSE_ENABLE(_X_) (*(_X_)->binding->bd_enable)(_X_) #define PARSE_DISABLE(_X_) (*(_X_)->binding->bd_disable)(_X_) #define PARSE_GETFMT(_X_, _DCT_) (*(_X_)->binding->bd_getfmt)(_X_, _DCT_) #define PARSE_SETFMT(_X_, _DCT_) (*(_X_)->binding->bd_setfmt)(_X_, _DCT_) #define PARSE_GETTIMECODE(_X_, _DCT_) (*(_X_)->binding->bd_timecode)(_X_, _DCT_) /* * io modes */ #define PARSE_F_PPSPPS 0x0001 /* use loopfilter PPS code (CIOGETEV) */ #define PARSE_F_PPSONSECOND 0x0002 /* PPS pulses are on second */ /**=========================================================================== ** error message regression handling ** ** there are quite a few errors that can occur in rapid succession such as ** noisy input data or no data at all. in order to reduce the amount of ** syslog messages in such case, we are using a backoff algorithm. We limit ** the number of error messages of a certain class to 1 per time unit. if a ** configurable number of messages is displayed that way, we move on to the ** next time unit / count for that class. a count of messages that have been ** suppressed is held and displayed whenever a corresponding message is ** displayed. the time units for a message class will also be displayed. ** whenever an error condition clears we reset the error message state, ** thus we would still generate much output on pathological conditions ** where the system oscillates between OK and NOT OK states. coping ** with that condition is currently considered too complicated. **/ #define ERR_ALL (unsigned)~0 /* "all" errors */ #define ERR_BADDATA (unsigned)0 /* unusable input data/conversion errors */ #define ERR_NODATA (unsigned)1 /* no input data */ #define ERR_BADIO (unsigned)2 /* read/write/select errors */ #define ERR_BADSTATUS (unsigned)3 /* unsync states */ #define ERR_BADEVENT (unsigned)4 /* non nominal events */ #define ERR_INTERNAL (unsigned)5 /* internal error */ #define ERR_CNT (unsigned)(ERR_INTERNAL+1) #define ERR(_X_) if (list_err(parse, (_X_))) struct errorregression { u_long err_count; /* number of repititions per class */ u_long err_delay; /* minimum delay between messages */ }; static struct errorregression err_baddata[] = /* error messages for bad input data */ { { 1, 0 }, /* output first message immediately */ { 5, 60 }, /* output next five messages in 60 second intervals */ { 3, 3600 }, /* output next 3 messages in hour intervals */ { 0, 12*3600 } /* repeat messages only every 12 hours */ }; static struct errorregression err_nodata[] = /* error messages for missing input data */ { { 1, 0 }, /* output first message immediately */ { 5, 60 }, /* output next five messages in 60 second intervals */ { 3, 3600 }, /* output next 3 messages in hour intervals */ { 0, 12*3600 } /* repeat messages only every 12 hours */ }; static struct errorregression err_badstatus[] = /* unsynchronized state messages */ { { 1, 0 }, /* output first message immediately */ { 5, 60 }, /* output next five messages in 60 second intervals */ { 3, 3600 }, /* output next 3 messages in hour intervals */ { 0, 12*3600 } /* repeat messages only every 12 hours */ }; static struct errorregression err_badio[] = /* io failures (bad reads, selects, ...) */ { { 1, 0 }, /* output first message immediately */ { 5, 60 }, /* output next five messages in 60 second intervals */ { 5, 3600 }, /* output next 3 messages in hour intervals */ { 0, 12*3600 } /* repeat messages only every 12 hours */ }; static struct errorregression err_badevent[] = /* non nominal events */ { { 20, 0 }, /* output first message immediately */ { 6, 60 }, /* output next five messages in 60 second intervals */ { 5, 3600 }, /* output next 3 messages in hour intervals */ { 0, 12*3600 } /* repeat messages only every 12 hours */ }; static struct errorregression err_internal[] = /* really bad things - basically coding/OS errors */ { { 0, 0 }, /* output all messages immediately */ }; static struct errorregression * err_tbl[] = { err_baddata, err_nodata, err_badio, err_badstatus, err_badevent, err_internal }; struct errorinfo { u_long err_started; /* begin time (ntp) of error condition */ u_long err_last; /* last time (ntp) error occurred */ u_long err_cnt; /* number of error repititions */ u_long err_suppressed; /* number of suppressed messages */ struct errorregression *err_stage; /* current error stage */ }; /**=========================================================================== ** refclock instance data **/ struct parseunit { /* * NTP management */ struct peer *peer; /* backlink to peer structure - refclock inactive if 0 */ struct refclockproc *generic; /* backlink to refclockproc structure */ /* * PARSE io */ bind_t *binding; /* io handling binding */ /* * parse state */ parse_t parseio; /* io handling structure (user level parsing) */ /* * type specific parameters */ struct parse_clockinfo *parse_type; /* link to clock description */ /* * clock state handling/reporting */ u_char flags; /* flags (leap_control) */ u_long lastchange; /* time (ntp) when last state change accured */ u_long statetime[CEVNT_MAX+1]; /* accumulated time of clock states */ u_long pollneeddata; /* current_time(!=0) for receive sample expected in PPS mode */ u_short lastformat; /* last format used */ u_long lastsync; /* time (ntp) when clock was last seen fully synchronized */ u_long lastmissed; /* time (ntp) when poll didn't get data (powerup heuristic) */ u_long ppsserial; /* magic cookie for ppsclock serials (avoids stale ppsclock data) */ parsetime_t time; /* last (parse module) data */ void *localdata; /* optional local, receiver-specific data */ unsigned long localstate; /* private local state */ struct errorinfo errors[ERR_CNT]; /* error state table for suppressing excessive error messages */ struct ctl_var *kv; /* additional pseudo variables */ u_long laststatistic; /* time when staticstics where output */ }; /**=========================================================================== ** Clockinfo section all parameter for specific clock types ** includes NTP parameters, TTY parameters and IO handling parameters **/ static void poll_dpoll P((struct parseunit *)); static void poll_poll P((struct peer *)); static int poll_init P((struct parseunit *)); typedef struct poll_info { u_long rate; /* poll rate - once every "rate" seconds - 0 off */ const char *string; /* string to send for polling */ u_long count; /* number of characters in string */ } poll_info_t; #define NO_CL_FLAGS 0 #define NO_POLL 0 #define NO_INIT 0 #define NO_END 0 #define NO_EVENT 0 #define NO_DATA 0 #define NO_MESSAGE 0 #define NO_PPSDELAY 0 #define DCF_ID "DCF" /* generic DCF */ #define DCF_A_ID "DCFa" /* AM demodulation */ #define DCF_P_ID "DCFp" /* psuedo random phase shift */ #define GPS_ID "GPS" /* GPS receiver */ #define NOCLOCK_ROOTDELAY 0.0 #define NOCLOCK_BASEDELAY 0.0 #define NOCLOCK_DESCRIPTION 0 #define NOCLOCK_MAXUNSYNC 0 #define NOCLOCK_CFLAG 0 #define NOCLOCK_IFLAG 0 #define NOCLOCK_OFLAG 0 #define NOCLOCK_LFLAG 0 #define NOCLOCK_ID "TILT" #define NOCLOCK_POLL NO_POLL #define NOCLOCK_INIT NO_INIT #define NOCLOCK_END NO_END #define NOCLOCK_DATA NO_DATA #define NOCLOCK_FORMAT "" #define NOCLOCK_TYPE CTL_SST_TS_UNSPEC #define NOCLOCK_SAMPLES 0 #define NOCLOCK_KEEP 0 #define DCF_TYPE CTL_SST_TS_LF #define GPS_TYPE CTL_SST_TS_UHF /* * receiver specific constants */ #define MBG_SPEED (B9600) #define MBG_CFLAG (CS7|PARENB|CREAD|CLOCAL|HUPCL) #define MBG_IFLAG (IGNBRK|IGNPAR|ISTRIP) #define MBG_OFLAG 0 #define MBG_LFLAG 0 #define MBG_FLAGS PARSE_F_PPSONSECOND /* * Meinberg DCF77 receivers */ #define DCFUA31_ROOTDELAY 0.0 /* 0 */ #define DCFUA31_BASEDELAY 0.010 /* 10.7421875ms: 10 ms (+/- 3 ms) */ #define DCFUA31_DESCRIPTION "Meinberg DCF77 C51 or compatible" #define DCFUA31_MAXUNSYNC 60*30 /* only trust clock for 1/2 hour */ #define DCFUA31_SPEED MBG_SPEED #define DCFUA31_CFLAG MBG_CFLAG #define DCFUA31_IFLAG MBG_IFLAG #define DCFUA31_OFLAG MBG_OFLAG #define DCFUA31_LFLAG MBG_LFLAG #define DCFUA31_SAMPLES 5 #define DCFUA31_KEEP 3 #define DCFUA31_FORMAT "Meinberg Standard" /* * Meinberg DCF PZF535/TCXO (FM/PZF) receiver */ #define DCFPZF535_ROOTDELAY 0.0 #define DCFPZF535_BASEDELAY 0.001968 /* 1.968ms +- 104us (oscilloscope) - relative to start (end of STX) */ #define DCFPZF535_DESCRIPTION "Meinberg DCF PZF 535/509 / TCXO" #define DCFPZF535_MAXUNSYNC 60*60*12 /* only trust clock for 12 hours * @ 5e-8df/f we have accumulated * at most 2.16 ms (thus we move to * NTP synchronisation */ #define DCFPZF535_SPEED MBG_SPEED #define DCFPZF535_CFLAG MBG_CFLAG #define DCFPZF535_IFLAG MBG_IFLAG #define DCFPZF535_OFLAG MBG_OFLAG #define DCFPZF535_LFLAG MBG_LFLAG #define DCFPZF535_SAMPLES 5 #define DCFPZF535_KEEP 3 #define DCFPZF535_FORMAT "Meinberg Standard" /* * Meinberg DCF PZF535/OCXO receiver */ #define DCFPZF535OCXO_ROOTDELAY 0.0 #define DCFPZF535OCXO_BASEDELAY 0.001968 /* 1.968ms +- 104us (oscilloscope) - relative to start (end of STX) */ #define DCFPZF535OCXO_DESCRIPTION "Meinberg DCF PZF 535/509 / OCXO" #define DCFPZF535OCXO_MAXUNSYNC 60*60*96 /* only trust clock for 4 days * @ 5e-9df/f we have accumulated * at most an error of 1.73 ms * (thus we move to NTP synchronisation) */ #define DCFPZF535OCXO_SPEED MBG_SPEED #define DCFPZF535OCXO_CFLAG MBG_CFLAG #define DCFPZF535OCXO_IFLAG MBG_IFLAG #define DCFPZF535OCXO_OFLAG MBG_OFLAG #define DCFPZF535OCXO_LFLAG MBG_LFLAG #define DCFPZF535OCXO_SAMPLES 5 #define DCFPZF535OCXO_KEEP 3 #define DCFPZF535OCXO_FORMAT "Meinberg Standard" /* * Meinberg GPS16X receiver */ static void gps16x_message P((struct parseunit *, parsetime_t *)); static int gps16x_poll_init P((struct parseunit *)); #define GPS16X_ROOTDELAY 0.0 /* nothing here */ #define GPS16X_BASEDELAY 0.001968 /* XXX to be fixed ! 1.968ms +- 104us (oscilloscope) - relative to start (end of STX) */ #define GPS16X_DESCRIPTION "Meinberg GPS16x receiver" #define GPS16X_MAXUNSYNC 60*60*96 /* only trust clock for 4 days * @ 5e-9df/f we have accumulated * at most an error of 1.73 ms * (thus we move to NTP synchronisation) */ #define GPS16X_SPEED B19200 #define GPS16X_CFLAG (CS8|CREAD|CLOCAL|HUPCL) #define GPS16X_IFLAG (IGNBRK|IGNPAR) #define GPS16X_OFLAG MBG_OFLAG #define GPS16X_LFLAG MBG_LFLAG #define GPS16X_POLLRATE 6 #define GPS16X_POLLCMD "" #define GPS16X_CMDSIZE 0 static poll_info_t gps16x_pollinfo = { GPS16X_POLLRATE, GPS16X_POLLCMD, GPS16X_CMDSIZE }; #define GPS16X_INIT gps16x_poll_init #define GPS16X_POLL 0 #define GPS16X_END 0 #define GPS16X_DATA ((void *)(&gps16x_pollinfo)) #define GPS16X_MESSAGE gps16x_message #define GPS16X_ID GPS_ID #define GPS16X_FORMAT "Meinberg GPS Extended" #define GPS16X_SAMPLES 5 #define GPS16X_KEEP 3 /* * ELV DCF7000 Wallclock-Receiver/Switching Clock (Kit) * * This is really not the hottest clock - but before you have nothing ... */ #define DCF7000_ROOTDELAY 0.0 /* 0 */ #define DCF7000_BASEDELAY 0.405 /* slow blow */ #define DCF7000_DESCRIPTION "ELV DCF7000" #define DCF7000_MAXUNSYNC (60*5) /* sorry - but it just was not build as a clock */ #define DCF7000_SPEED (B9600) #define DCF7000_CFLAG (CS8|CREAD|PARENB|PARODD|CLOCAL|HUPCL) #define DCF7000_IFLAG (IGNBRK) #define DCF7000_OFLAG 0 #define DCF7000_LFLAG 0 #define DCF7000_SAMPLES 5 #define DCF7000_KEEP 3 #define DCF7000_FORMAT "ELV DCF7000" /* * Schmid DCF Receiver Kit * * When the WSDCF clock is operating optimally we want the primary clock * distance to come out at 300 ms. Thus, peer.distance in the WSDCF peer * structure is set to 290 ms and we compute delays which are at least * 10 ms long. The following are 290 ms and 10 ms expressed in u_fp format */ #define WS_POLLRATE 1 /* every second - watch interdependency with poll routine */ #define WS_POLLCMD "\163" #define WS_CMDSIZE 1 static poll_info_t wsdcf_pollinfo = { WS_POLLRATE, WS_POLLCMD, WS_CMDSIZE }; #define WSDCF_INIT poll_init #define WSDCF_POLL poll_dpoll #define WSDCF_END 0 #define WSDCF_DATA ((void *)(&wsdcf_pollinfo)) #define WSDCF_ROOTDELAY 0.0 /* 0 */ #define WSDCF_BASEDELAY 0.010 /* ~ 10ms */ #define WSDCF_DESCRIPTION "WS/DCF Receiver" #define WSDCF_FORMAT "Schmid" #define WSDCF_MAXUNSYNC (60*60) /* assume this beast hold at 1 h better than 2 ms XXX-must verify */ #define WSDCF_SPEED (B1200) #define WSDCF_CFLAG (CS8|CREAD|CLOCAL) #define WSDCF_IFLAG 0 #define WSDCF_OFLAG 0 #define WSDCF_LFLAG 0 #define WSDCF_SAMPLES 5 #define WSDCF_KEEP 3 /* * RAW DCF77 - input of DCF marks via RS232 - many variants */ #define RAWDCF_FLAGS 0 #define RAWDCF_ROOTDELAY 0.0 /* 0 */ #define RAWDCF_BASEDELAY 0.258 #define RAWDCF_FORMAT "RAW DCF77 Timecode" #define RAWDCF_MAXUNSYNC (0) /* sorry - its a true receiver - no signal - no time */ #define RAWDCF_SPEED (B50) #ifdef NO_PARENB_IGNPAR /* Was: defined(SYS_IRIX4) || defined(SYS_IRIX5) */ /* somehow doesn't grok PARENB & IGNPAR (mj) */ # define RAWDCF_CFLAG (CS8|CREAD|CLOCAL) #else # define RAWDCF_CFLAG (CS8|CREAD|CLOCAL|PARENB) #endif #ifdef RAWDCF_NO_IGNPAR /* Was: defined(SYS_LINUX) && defined(CLOCK_RAWDCF) */ # define RAWDCF_IFLAG 0 #else # define RAWDCF_IFLAG (IGNPAR) #endif #define RAWDCF_OFLAG 0 #define RAWDCF_LFLAG 0 #define RAWDCF_SAMPLES 20 #define RAWDCF_KEEP 12 #define RAWDCF_INIT 0 /* * RAW DCF variants */ /* * Conrad receiver * * simplest (cheapest) DCF clock - e. g. DCF77 receiver by Conrad * (~40DM - roughly $30 ) followed by a level converter for RS232 */ #define CONRAD_BASEDELAY 0.292 /* Conrad receiver @ 50 Baud on a Sun */ #define CONRAD_DESCRIPTION "RAW DCF77 CODE (Conrad DCF77 receiver module)" /* * TimeBrick receiver */ #define TIMEBRICK_BASEDELAY 0.210 /* TimeBrick @ 50 Baud on a Sun */ #define TIMEBRICK_DESCRIPTION "RAW DCF77 CODE (TimeBrick)" /* * IGEL:clock receiver */ #define IGELCLOCK_BASEDELAY 0.258 /* IGEL:clock receiver */ #define IGELCLOCK_DESCRIPTION "RAW DCF77 CODE (IGEL:clock)" #define IGELCLOCK_SPEED (B1200) #define IGELCLOCK_CFLAG (CS8|CREAD|HUPCL|CLOCAL) /* * RAWDCF receivers that need to be powered from DTR * (like Expert mouse clock) */ static int rawdcf_init_1 P((struct parseunit *)); #define RAWDCFDTRSET_DESCRIPTION "RAW DCF77 CODE (DTR SET/RTS CLR)" #define RAWDCFDTRSET_INIT rawdcf_init_1 /* * RAWDCF receivers that need to be powered from * DTR CLR and RTS SET */ static int rawdcf_init_2 P((struct parseunit *)); #define RAWDCFDTRCLRRTSSET_DESCRIPTION "RAW DCF77 CODE (DTR CLR/RTS SET)" #define RAWDCFDTRCLRRTSSET_INIT rawdcf_init_2 /* * Trimble GPS receivers (TAIP and TSIP protocols) */ #ifndef TRIM_POLLRATE #define TRIM_POLLRATE 0 /* only true direct polling */ #endif #define TRIM_TAIPPOLLCMD ">SRM;FR_FLAG=F;EC_FLAG=F<>QTM<" #define TRIM_TAIPCMDSIZE (sizeof(TRIM_TAIPPOLLCMD)-1) static poll_info_t trimbletaip_pollinfo = { TRIM_POLLRATE, TRIM_TAIPPOLLCMD, TRIM_TAIPCMDSIZE }; static int trimbletaip_init P((struct parseunit *)); static void trimbletaip_event P((struct parseunit *, int)); /* query time & UTC correction data */ static char tsipquery[] = { DLE, 0x21, DLE, ETX, DLE, 0x2F, DLE, ETX }; static poll_info_t trimbletsip_pollinfo = { TRIM_POLLRATE, tsipquery, sizeof(tsipquery) }; static int trimbletsip_init P((struct parseunit *)); static void trimbletsip_end P((struct parseunit *)); static void trimbletsip_message P((struct parseunit *, parsetime_t *)); static void trimbletsip_event P((struct parseunit *, int)); #define TRIMBLETSIP_IDLE_TIME (300) /* 5 minutes silence at most */ #define TRIMBLETAIP_SPEED (B4800) #define TRIMBLETAIP_CFLAG (CS8|CREAD|CLOCAL) #define TRIMBLETAIP_IFLAG (BRKINT|IGNPAR|ISTRIP|ICRNL|IXON) #define TRIMBLETAIP_OFLAG (OPOST|ONLCR) #define TRIMBLETAIP_LFLAG (0) #define TRIMBLETSIP_SPEED (B9600) #define TRIMBLETSIP_CFLAG (CS8|CLOCAL|CREAD|PARENB|PARODD) #define TRIMBLETSIP_IFLAG (IGNBRK) #define TRIMBLETSIP_OFLAG (0) #define TRIMBLETSIP_LFLAG (ICANON) #define TRIMBLETSIP_SAMPLES 5 #define TRIMBLETSIP_KEEP 3 #define TRIMBLETAIP_SAMPLES 5 #define TRIMBLETAIP_KEEP 3 #define TRIMBLETAIP_FLAGS (PARSE_F_PPSONSECOND) #define TRIMBLETSIP_FLAGS (TRIMBLETAIP_FLAGS) #define TRIMBLETAIP_POLL poll_dpoll #define TRIMBLETSIP_POLL poll_dpoll #define TRIMBLETAIP_INIT trimbletaip_init #define TRIMBLETSIP_INIT trimbletsip_init #define TRIMBLETAIP_EVENT trimbletaip_event #define TRIMBLETSIP_EVENT trimbletsip_event #define TRIMBLETSIP_MESSAGE trimbletsip_message #define TRIMBLETAIP_END 0 #define TRIMBLETSIP_END trimbletsip_end #define TRIMBLETAIP_DATA ((void *)(&trimbletaip_pollinfo)) #define TRIMBLETSIP_DATA ((void *)(&trimbletsip_pollinfo)) #define TRIMBLETAIP_ID GPS_ID #define TRIMBLETSIP_ID GPS_ID #define TRIMBLETAIP_FORMAT "Trimble TAIP" #define TRIMBLETSIP_FORMAT "Trimble TSIP" #define TRIMBLETAIP_ROOTDELAY 0x0 #define TRIMBLETSIP_ROOTDELAY 0x0 #define TRIMBLETAIP_BASEDELAY 0.0 #define TRIMBLETSIP_BASEDELAY 0.020 /* GPS time message latency */ #define TRIMBLETAIP_DESCRIPTION "Trimble GPS (TAIP) receiver" #define TRIMBLETSIP_DESCRIPTION "Trimble GPS (TSIP) receiver" #define TRIMBLETAIP_MAXUNSYNC 0 #define TRIMBLETSIP_MAXUNSYNC 0 #define TRIMBLETAIP_EOL '<' /* * RadioCode Clocks RCC 800 receiver */ #define RCC_POLLRATE 0 /* only true direct polling */ #define RCC_POLLCMD "\r" #define RCC_CMDSIZE 1 static poll_info_t rcc8000_pollinfo = { RCC_POLLRATE, RCC_POLLCMD, RCC_CMDSIZE }; #define RCC8000_FLAGS 0 #define RCC8000_POLL poll_dpoll #define RCC8000_INIT poll_init #define RCC8000_END 0 #define RCC8000_DATA ((void *)(&rcc8000_pollinfo)) #define RCC8000_ROOTDELAY 0.0 #define RCC8000_BASEDELAY 0.0 #define RCC8000_ID "MSF" #define RCC8000_DESCRIPTION "RCC 8000 MSF Receiver" #define RCC8000_FORMAT "Radiocode RCC8000" #define RCC8000_MAXUNSYNC (60*60) /* should be ok for an hour */ #define RCC8000_SPEED (B2400) #define RCC8000_CFLAG (CS8|CREAD|CLOCAL) #define RCC8000_IFLAG (IGNBRK|IGNPAR) #define RCC8000_OFLAG 0 #define RCC8000_LFLAG 0 #define RCC8000_SAMPLES 5 #define RCC8000_KEEP 3 /* * Hopf Radio clock 6021 Format * */ #define HOPF6021_ROOTDELAY 0.0 #define HOPF6021_BASEDELAY 0.0 #define HOPF6021_DESCRIPTION "HOPF 6021" #define HOPF6021_FORMAT "hopf Funkuhr 6021" #define HOPF6021_MAXUNSYNC (60*60) /* should be ok for an hour */ #define HOPF6021_SPEED (B9600) #define HOPF6021_CFLAG (CS8|CREAD|CLOCAL) #define HOPF6021_IFLAG (IGNBRK|ISTRIP) #define HOPF6021_OFLAG 0 #define HOPF6021_LFLAG 0 #define HOPF6021_FLAGS 0 #define HOPF6021_SAMPLES 5 #define HOPF6021_KEEP 3 /* * Diem's Computime Radio Clock Receiver */ #define COMPUTIME_FLAGS 0 #define COMPUTIME_ROOTDELAY 0.0 #define COMPUTIME_BASEDELAY 0.0 #define COMPUTIME_ID DCF_ID #define COMPUTIME_DESCRIPTION "Diem's Computime receiver" #define COMPUTIME_FORMAT "Diem's Computime Radio Clock" #define COMPUTIME_TYPE DCF_TYPE #define COMPUTIME_MAXUNSYNC (60*60) /* only trust clock for 1 hour */ #define COMPUTIME_SPEED (B9600) #define COMPUTIME_CFLAG (CSTOPB|CS7|CREAD|CLOCAL) #define COMPUTIME_IFLAG (IGNBRK|IGNPAR|ISTRIP) #define COMPUTIME_OFLAG 0 #define COMPUTIME_LFLAG 0 #define COMPUTIME_SAMPLES 5 #define COMPUTIME_KEEP 3 /* * Varitext Radio Clock Receiver */ #define VARITEXT_FLAGS 0 #define VARITEXT_ROOTDELAY 0.0 #define VARITEXT_BASEDELAY 0.0 #define VARITEXT_ID "MSF" #define VARITEXT_DESCRIPTION "Varitext receiver" #define VARITEXT_FORMAT "Varitext Radio Clock" #define VARITEXT_TYPE DCF_TYPE #define VARITEXT_MAXUNSYNC (60*60) /* only trust clock for 1 hour */ #define VARITEXT_SPEED (B9600) #define VARITEXT_CFLAG (CS7|CREAD|CLOCAL|PARENB|PARODD) #define VARITEXT_IFLAG (IGNPAR|IGNBRK|INPCK) /*|ISTRIP)*/ #define VARITEXT_OFLAG 0 #define VARITEXT_LFLAG 0 #define VARITEXT_SAMPLES 32 #define VARITEXT_KEEP 20 static struct parse_clockinfo { u_long cl_flags; /* operation flags (io modes) */ void (*cl_poll) P((struct parseunit *)); /* active poll routine */ int (*cl_init) P((struct parseunit *)); /* active poll init routine */ void (*cl_event) P((struct parseunit *, int)); /* special event handling (e.g. reset clock) */ void (*cl_end) P((struct parseunit *)); /* active poll end routine */ void (*cl_message) P((struct parseunit *, parsetime_t *)); /* process a lower layer message */ void *cl_data; /* local data area for "poll" mechanism */ double cl_rootdelay; /* rootdelay */ double cl_basedelay; /* current offset by which the RS232 time code is delayed from the actual time */ const char *cl_id; /* ID code */ const char *cl_description; /* device name */ const char *cl_format; /* fixed format */ u_char cl_type; /* clock type (ntp control) */ u_long cl_maxunsync; /* time to trust oscillator after losing synch */ u_long cl_speed; /* terminal input & output baudrate */ u_long cl_cflag; /* terminal control flags */ u_long cl_iflag; /* terminal input flags */ u_long cl_oflag; /* terminal output flags */ u_long cl_lflag; /* terminal local flags */ u_long cl_samples; /* samples for median filter */ u_long cl_keep; /* samples for median filter to keep */ } parse_clockinfo[] = { { /* mode 0 */ MBG_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, DCFPZF535_ROOTDELAY, DCFPZF535_BASEDELAY, DCF_P_ID, DCFPZF535_DESCRIPTION, DCFPZF535_FORMAT, DCF_TYPE, DCFPZF535_MAXUNSYNC, DCFPZF535_SPEED, DCFPZF535_CFLAG, DCFPZF535_IFLAG, DCFPZF535_OFLAG, DCFPZF535_LFLAG, DCFPZF535_SAMPLES, DCFPZF535_KEEP }, { /* mode 1 */ MBG_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, DCFPZF535OCXO_ROOTDELAY, DCFPZF535OCXO_BASEDELAY, DCF_P_ID, DCFPZF535OCXO_DESCRIPTION, DCFPZF535OCXO_FORMAT, DCF_TYPE, DCFPZF535OCXO_MAXUNSYNC, DCFPZF535OCXO_SPEED, DCFPZF535OCXO_CFLAG, DCFPZF535OCXO_IFLAG, DCFPZF535OCXO_OFLAG, DCFPZF535OCXO_LFLAG, DCFPZF535OCXO_SAMPLES, DCFPZF535OCXO_KEEP }, { /* mode 2 */ MBG_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, DCFUA31_ROOTDELAY, DCFUA31_BASEDELAY, DCF_A_ID, DCFUA31_DESCRIPTION, DCFUA31_FORMAT, DCF_TYPE, DCFUA31_MAXUNSYNC, DCFUA31_SPEED, DCFUA31_CFLAG, DCFUA31_IFLAG, DCFUA31_OFLAG, DCFUA31_LFLAG, DCFUA31_SAMPLES, DCFUA31_KEEP }, { /* mode 3 */ MBG_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, DCF7000_ROOTDELAY, DCF7000_BASEDELAY, DCF_A_ID, DCF7000_DESCRIPTION, DCF7000_FORMAT, DCF_TYPE, DCF7000_MAXUNSYNC, DCF7000_SPEED, DCF7000_CFLAG, DCF7000_IFLAG, DCF7000_OFLAG, DCF7000_LFLAG, DCF7000_SAMPLES, DCF7000_KEEP }, { /* mode 4 */ NO_CL_FLAGS, WSDCF_POLL, WSDCF_INIT, NO_EVENT, WSDCF_END, NO_MESSAGE, WSDCF_DATA, WSDCF_ROOTDELAY, WSDCF_BASEDELAY, DCF_A_ID, WSDCF_DESCRIPTION, WSDCF_FORMAT, DCF_TYPE, WSDCF_MAXUNSYNC, WSDCF_SPEED, WSDCF_CFLAG, WSDCF_IFLAG, WSDCF_OFLAG, WSDCF_LFLAG, WSDCF_SAMPLES, WSDCF_KEEP }, { /* mode 5 */ RAWDCF_FLAGS, NO_POLL, RAWDCF_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, RAWDCF_ROOTDELAY, CONRAD_BASEDELAY, DCF_A_ID, CONRAD_DESCRIPTION, RAWDCF_FORMAT, DCF_TYPE, RAWDCF_MAXUNSYNC, RAWDCF_SPEED, RAWDCF_CFLAG, RAWDCF_IFLAG, RAWDCF_OFLAG, RAWDCF_LFLAG, RAWDCF_SAMPLES, RAWDCF_KEEP }, { /* mode 6 */ RAWDCF_FLAGS, NO_POLL, RAWDCF_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, RAWDCF_ROOTDELAY, TIMEBRICK_BASEDELAY, DCF_A_ID, TIMEBRICK_DESCRIPTION, RAWDCF_FORMAT, DCF_TYPE, RAWDCF_MAXUNSYNC, RAWDCF_SPEED, RAWDCF_CFLAG, RAWDCF_IFLAG, RAWDCF_OFLAG, RAWDCF_LFLAG, RAWDCF_SAMPLES, RAWDCF_KEEP }, { /* mode 7 */ MBG_FLAGS, GPS16X_POLL, GPS16X_INIT, NO_EVENT, GPS16X_END, GPS16X_MESSAGE, GPS16X_DATA, GPS16X_ROOTDELAY, GPS16X_BASEDELAY, GPS16X_ID, GPS16X_DESCRIPTION, GPS16X_FORMAT, GPS_TYPE, GPS16X_MAXUNSYNC, GPS16X_SPEED, GPS16X_CFLAG, GPS16X_IFLAG, GPS16X_OFLAG, GPS16X_LFLAG, GPS16X_SAMPLES, GPS16X_KEEP }, { /* mode 8 */ RAWDCF_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, RAWDCF_ROOTDELAY, IGELCLOCK_BASEDELAY, DCF_A_ID, IGELCLOCK_DESCRIPTION, RAWDCF_FORMAT, DCF_TYPE, RAWDCF_MAXUNSYNC, IGELCLOCK_SPEED, IGELCLOCK_CFLAG, RAWDCF_IFLAG, RAWDCF_OFLAG, RAWDCF_LFLAG, RAWDCF_SAMPLES, RAWDCF_KEEP }, { /* mode 9 */ TRIMBLETAIP_FLAGS, #if TRIM_POLLRATE /* DHD940515: Allow user config */ NO_POLL, #else TRIMBLETAIP_POLL, #endif TRIMBLETAIP_INIT, TRIMBLETAIP_EVENT, TRIMBLETAIP_END, NO_MESSAGE, TRIMBLETAIP_DATA, TRIMBLETAIP_ROOTDELAY, TRIMBLETAIP_BASEDELAY, TRIMBLETAIP_ID, TRIMBLETAIP_DESCRIPTION, TRIMBLETAIP_FORMAT, GPS_TYPE, TRIMBLETAIP_MAXUNSYNC, TRIMBLETAIP_SPEED, TRIMBLETAIP_CFLAG, TRIMBLETAIP_IFLAG, TRIMBLETAIP_OFLAG, TRIMBLETAIP_LFLAG, TRIMBLETAIP_SAMPLES, TRIMBLETAIP_KEEP }, { /* mode 10 */ TRIMBLETSIP_FLAGS, #if TRIM_POLLRATE /* DHD940515: Allow user config */ NO_POLL, #else TRIMBLETSIP_POLL, #endif TRIMBLETSIP_INIT, TRIMBLETSIP_EVENT, TRIMBLETSIP_END, TRIMBLETSIP_MESSAGE, TRIMBLETSIP_DATA, TRIMBLETSIP_ROOTDELAY, TRIMBLETSIP_BASEDELAY, TRIMBLETSIP_ID, TRIMBLETSIP_DESCRIPTION, TRIMBLETSIP_FORMAT, GPS_TYPE, TRIMBLETSIP_MAXUNSYNC, TRIMBLETSIP_SPEED, TRIMBLETSIP_CFLAG, TRIMBLETSIP_IFLAG, TRIMBLETSIP_OFLAG, TRIMBLETSIP_LFLAG, TRIMBLETSIP_SAMPLES, TRIMBLETSIP_KEEP }, { /* mode 11 */ NO_CL_FLAGS, RCC8000_POLL, RCC8000_INIT, NO_EVENT, RCC8000_END, NO_MESSAGE, RCC8000_DATA, RCC8000_ROOTDELAY, RCC8000_BASEDELAY, RCC8000_ID, RCC8000_DESCRIPTION, RCC8000_FORMAT, DCF_TYPE, RCC8000_MAXUNSYNC, RCC8000_SPEED, RCC8000_CFLAG, RCC8000_IFLAG, RCC8000_OFLAG, RCC8000_LFLAG, RCC8000_SAMPLES, RCC8000_KEEP }, { /* mode 12 */ HOPF6021_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, HOPF6021_ROOTDELAY, HOPF6021_BASEDELAY, DCF_ID, HOPF6021_DESCRIPTION, HOPF6021_FORMAT, DCF_TYPE, HOPF6021_MAXUNSYNC, HOPF6021_SPEED, HOPF6021_CFLAG, HOPF6021_IFLAG, HOPF6021_OFLAG, HOPF6021_LFLAG, HOPF6021_SAMPLES, HOPF6021_KEEP }, { /* mode 13 */ COMPUTIME_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, COMPUTIME_ROOTDELAY, COMPUTIME_BASEDELAY, COMPUTIME_ID, COMPUTIME_DESCRIPTION, COMPUTIME_FORMAT, COMPUTIME_TYPE, COMPUTIME_MAXUNSYNC, COMPUTIME_SPEED, COMPUTIME_CFLAG, COMPUTIME_IFLAG, COMPUTIME_OFLAG, COMPUTIME_LFLAG, COMPUTIME_SAMPLES, COMPUTIME_KEEP }, { /* mode 14 */ RAWDCF_FLAGS, NO_POLL, RAWDCFDTRSET_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, RAWDCF_ROOTDELAY, RAWDCF_BASEDELAY, DCF_A_ID, RAWDCFDTRSET_DESCRIPTION, RAWDCF_FORMAT, DCF_TYPE, RAWDCF_MAXUNSYNC, RAWDCF_SPEED, RAWDCF_CFLAG, RAWDCF_IFLAG, RAWDCF_OFLAG, RAWDCF_LFLAG, RAWDCF_SAMPLES, RAWDCF_KEEP }, { /* mode 15 */ 0, /* operation flags (io modes) */ NO_POLL, /* active poll routine */ NO_INIT, /* active poll init routine */ NO_EVENT, /* special event handling (e.g. reset clock) */ NO_END, /* active poll end routine */ NO_MESSAGE, /* process a lower layer message */ NO_DATA, /* local data area for "poll" mechanism */ 0, /* rootdelay */ 11.0 /* bits */ / 9600, /* current offset by which the RS232 time code is delayed from the actual time */ DCF_ID, /* ID code */ "WHARTON 400A Series clock", /* device name */ "WHARTON 400A Series clock Output Format 1", /* fixed format */ /* Must match a format-name in a libparse/clk_xxx.c file */ DCF_TYPE, /* clock type (ntp control) */ (1*60*60), /* time to trust oscillator after losing synch */ B9600, /* terminal input & output baudrate */ (CS8|CREAD|PARENB|CLOCAL|HUPCL),/* terminal control flags */ 0, /* terminal input flags */ 0, /* terminal output flags */ 0, /* terminal local flags */ 5, /* samples for median filter */ 3, /* samples for median filter to keep */ }, { /* mode 16 - RAWDCF RTS set, DTR clr */ RAWDCF_FLAGS, NO_POLL, RAWDCFDTRCLRRTSSET_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, RAWDCF_ROOTDELAY, RAWDCF_BASEDELAY, DCF_A_ID, RAWDCFDTRCLRRTSSET_DESCRIPTION, RAWDCF_FORMAT, DCF_TYPE, RAWDCF_MAXUNSYNC, RAWDCF_SPEED, RAWDCF_CFLAG, RAWDCF_IFLAG, RAWDCF_OFLAG, RAWDCF_LFLAG, RAWDCF_SAMPLES, RAWDCF_KEEP }, { /* mode 17 */ VARITEXT_FLAGS, NO_POLL, NO_INIT, NO_EVENT, NO_END, NO_MESSAGE, NO_DATA, VARITEXT_ROOTDELAY, VARITEXT_BASEDELAY, VARITEXT_ID, VARITEXT_DESCRIPTION, VARITEXT_FORMAT, VARITEXT_TYPE, VARITEXT_MAXUNSYNC, VARITEXT_SPEED, VARITEXT_CFLAG, VARITEXT_IFLAG, VARITEXT_OFLAG, VARITEXT_LFLAG, VARITEXT_SAMPLES, VARITEXT_KEEP } }; static int ncltypes = sizeof(parse_clockinfo) / sizeof(struct parse_clockinfo); #define CLK_REALTYPE(x) ((int)(((x)->ttl) & 0x7F)) #define CLK_TYPE(x) ((CLK_REALTYPE(x) >= ncltypes) ? ~0 : CLK_REALTYPE(x)) #define CLK_UNIT(x) ((int)REFCLOCKUNIT(&(x)->srcadr)) #define CLK_PPS(x) (((x)->ttl) & 0x80) /* * Other constant stuff */ #define PARSEHSREFID 0x7f7f08ff /* 127.127.8.255 refid for hi strata */ #define PARSESTATISTICS (60*60) /* output state statistics every hour */ static struct parseunit *parseunits[MAXUNITS]; static int notice = 0; #define PARSE_STATETIME(parse, i) ((parse->generic->currentstatus == i) ? parse->statetime[i] + current_time - parse->lastchange : parse->statetime[i]) static void parse_event P((struct parseunit *, int)); static void parse_process P((struct parseunit *, parsetime_t *)); static void clear_err P((struct parseunit *, u_long)); static int list_err P((struct parseunit *, u_long)); static char * l_mktime P((u_long)); /**=========================================================================== ** implementation error message regression module **/ static void clear_err( struct parseunit *parse, u_long lstate ) { if (lstate == ERR_ALL) { int i; for (i = 0; i < ERR_CNT; i++) { parse->errors[i].err_stage = err_tbl[i]; parse->errors[i].err_cnt = 0; parse->errors[i].err_last = 0; parse->errors[i].err_started = 0; parse->errors[i].err_suppressed = 0; } } else { parse->errors[lstate].err_stage = err_tbl[lstate]; parse->errors[lstate].err_cnt = 0; parse->errors[lstate].err_last = 0; parse->errors[lstate].err_started = 0; parse->errors[lstate].err_suppressed = 0; } } static int list_err( struct parseunit *parse, u_long lstate ) { int do_it; struct errorinfo *err = &parse->errors[lstate]; if (err->err_started == 0) { err->err_started = current_time; } do_it = (current_time - err->err_last) >= err->err_stage->err_delay; if (do_it) err->err_cnt++; if (err->err_stage->err_count && (err->err_cnt >= err->err_stage->err_count)) { err->err_stage++; err->err_cnt = 0; } if (!err->err_cnt && do_it) msyslog(LOG_INFO, "PARSE receiver #%d: interval for following error message class is at least %s", CLK_UNIT(parse->peer), l_mktime(err->err_stage->err_delay)); if (!do_it) err->err_suppressed++; else err->err_last = current_time; if (do_it && err->err_suppressed) { msyslog(LOG_INFO, "PARSE receiver #%d: %ld message%s suppressed, error condition class persists for %s", CLK_UNIT(parse->peer), err->err_suppressed, (err->err_suppressed == 1) ? " was" : "s where", l_mktime(current_time - err->err_started)); err->err_suppressed = 0; } return do_it; } /*-------------------------------------------------- * mkreadable - make a printable ascii string (without * embedded quotes so that the ntpq protocol isn't * fooled */ #ifndef isprint #define isprint(_X_) (((_X_) > 0x1F) && ((_X_) < 0x7F)) #endif static char * mkreadable( char *buffer, long blen, const char *src, u_long srclen, int hex ) { char *b = buffer; char *endb = (char *)0; if (blen < 4) return (char *)0; /* don't bother with mini buffers */ endb = buffer + blen - 4; blen--; /* account for '\0' */ while (blen && srclen--) { if (!hex && /* no binary only */ (*src != '\\') && /* no plain \ */ (*src != '"') && /* no " */ isprint((int)*src)) /* only printables */ { /* they are easy... */ *buffer++ = *src++; blen--; } else { if (blen < 4) { while (blen--) { *buffer++ = '.'; } *buffer = '\0'; return b; } else { if (*src == '\\') { strcpy(buffer,"\\\\"); buffer += 2; blen -= 2; src++; } else { sprintf(buffer, "\\x%02x", *src++); blen -= 4; buffer += 4; } } } if (srclen && !blen && endb) /* overflow - set last chars to ... */ strcpy(endb, "..."); } *buffer = '\0'; return b; } /*-------------------------------------------------- * mkascii - make a printable ascii string * assumes (unless defined better) 7-bit ASCII */ static char * mkascii( char *buffer, long blen, const char *src, u_long srclen ) { return mkreadable(buffer, blen, src, srclen, 0); } /**=========================================================================== ** implementation of i/o handling methods ** (all STREAM, partial STREAM, user level) **/ /* * define possible io handling methods */ #ifdef STREAM static int ppsclock_init P((struct parseunit *)); static int stream_init P((struct parseunit *)); static void stream_end P((struct parseunit *)); static int stream_enable P((struct parseunit *)); static int stream_disable P((struct parseunit *)); static int stream_setcs P((struct parseunit *, parsectl_t *)); static int stream_getfmt P((struct parseunit *, parsectl_t *)); static int stream_setfmt P((struct parseunit *, parsectl_t *)); static int stream_timecode P((struct parseunit *, parsectl_t *)); static void stream_receive P((struct recvbuf *)); #endif static int local_init P((struct parseunit *)); static void local_end P((struct parseunit *)); static int local_nop P((struct parseunit *)); static int local_setcs P((struct parseunit *, parsectl_t *)); static int local_getfmt P((struct parseunit *, parsectl_t *)); static int local_setfmt P((struct parseunit *, parsectl_t *)); static int local_timecode P((struct parseunit *, parsectl_t *)); static void local_receive P((struct recvbuf *)); static int local_input P((struct recvbuf *)); static bind_t io_bindings[] = { #ifdef STREAM { "parse STREAM", stream_init, stream_end, stream_setcs, stream_disable, stream_enable, stream_getfmt, stream_setfmt, stream_timecode, stream_receive, 0, }, { "ppsclock STREAM", ppsclock_init, local_end, local_setcs, local_nop, local_nop, local_getfmt, local_setfmt, local_timecode, local_receive, local_input, }, #endif { "normal", local_init, local_end, local_setcs, local_nop, local_nop, local_getfmt, local_setfmt, local_timecode, local_receive, local_input, }, { (char *)0, } }; #ifdef STREAM #define fix_ts(_X_) \ if ((&(_X_))->tv.tv_usec >= 1000000) \ { \ (&(_X_))->tv.tv_usec -= 1000000; \ (&(_X_))->tv.tv_sec += 1; \ } #define cvt_ts(_X_, _Y_) \ { \ l_fp ts; \ fix_ts((_X_)); \ if (!buftvtots((const char *)&(&(_X_))->tv, &ts)) \ { \ ERR(ERR_BADDATA) \ msyslog(LOG_ERR,"parse: stream_receive: timestamp conversion error (buftvtots) (%s) (%ld.%06ld) ", (_Y_), (long)(&(_X_))->tv.tv_sec, (long)(&(_X_))->tv.tv_usec);\ return; \ } \ else \ { \ (&(_X_))->fp = ts; \ } \ } /*-------------------------------------------------- * ppsclock STREAM init */ static int ppsclock_init( struct parseunit *parse ) { static char m1[] = "ppsclocd"; static char m2[] = "ppsclock"; /* * now push the parse streams module * it will ensure exclusive access to the device */ if (ioctl(parse->generic->io.fd, I_PUSH, (caddr_t)m1) == -1 && ioctl(parse->generic->io.fd, I_PUSH, (caddr_t)m2) == -1) { if (errno != EINVAL) { msyslog(LOG_ERR, "PARSE receiver #%d: ppsclock_init: ioctl(fd, I_PUSH, \"ppsclock\"): %m", CLK_UNIT(parse->peer)); } return 0; } if (!local_init(parse)) { (void)ioctl(parse->generic->io.fd, I_POP, (caddr_t)0); return 0; } parse->flags |= PARSE_PPSCLOCK; return 1; } /*-------------------------------------------------- * parse STREAM init */ static int stream_init( struct parseunit *parse ) { static char m1[] = "parse"; /* * now push the parse streams module * to test whether it is there (neat interface 8-( ) */ if (ioctl(parse->generic->io.fd, I_PUSH, (caddr_t)m1) == -1) { if (errno != EINVAL) /* accept non-existence */ { msyslog(LOG_ERR, "PARSE receiver #%d: stream_init: ioctl(fd, I_PUSH, \"parse\"): %m", CLK_UNIT(parse->peer)); } return 0; } else { while(ioctl(parse->generic->io.fd, I_POP, (caddr_t)0) == 0) /* empty loop */; /* * now push it a second time after we have removed all * module garbage */ if (ioctl(parse->generic->io.fd, I_PUSH, (caddr_t)m1) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: stream_init: ioctl(fd, I_PUSH, \"parse\"): %m", CLK_UNIT(parse->peer)); return 0; } else { return 1; } } } /*-------------------------------------------------- * parse STREAM end */ static void stream_end( struct parseunit *parse ) { while(ioctl(parse->generic->io.fd, I_POP, (caddr_t)0) == 0) /* empty loop */; } /*-------------------------------------------------- * STREAM setcs */ static int stream_setcs( struct parseunit *parse, parsectl_t *tcl ) { struct strioctl strioc; strioc.ic_cmd = PARSEIOC_SETCS; strioc.ic_timout = 0; strioc.ic_dp = (char *)tcl; strioc.ic_len = sizeof (*tcl); if (ioctl(parse->generic->io.fd, I_STR, (caddr_t)&strioc) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: stream_setcs: ioctl(fd, I_STR, PARSEIOC_SETCS): %m", CLK_UNIT(parse->peer)); return 0; } return 1; } /*-------------------------------------------------- * STREAM enable */ static int stream_enable( struct parseunit *parse ) { struct strioctl strioc; strioc.ic_cmd = PARSEIOC_ENABLE; strioc.ic_timout = 0; strioc.ic_dp = (char *)0; strioc.ic_len = 0; if (ioctl(parse->generic->io.fd, I_STR, (caddr_t)&strioc) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: stream_enable: ioctl(fd, I_STR, PARSEIOC_ENABLE): %m", CLK_UNIT(parse->peer)); return 0; } parse->generic->io.clock_recv = stream_receive; /* ok - parse input in kernel */ return 1; } /*-------------------------------------------------- * STREAM disable */ static int stream_disable( struct parseunit *parse ) { struct strioctl strioc; strioc.ic_cmd = PARSEIOC_DISABLE; strioc.ic_timout = 0; strioc.ic_dp = (char *)0; strioc.ic_len = 0; if (ioctl(parse->generic->io.fd, I_STR, (caddr_t)&strioc) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: stream_disable: ioctl(fd, I_STR, PARSEIOC_DISABLE): %m", CLK_UNIT(parse->peer)); return 0; } parse->generic->io.clock_recv = local_receive; /* ok - parse input in daemon */ return 1; } /*-------------------------------------------------- * STREAM getfmt */ static int stream_getfmt( struct parseunit *parse, parsectl_t *tcl ) { struct strioctl strioc; strioc.ic_cmd = PARSEIOC_GETFMT; strioc.ic_timout = 0; strioc.ic_dp = (char *)tcl; strioc.ic_len = sizeof (*tcl); if (ioctl(parse->generic->io.fd, I_STR, (caddr_t)&strioc) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: ioctl(fd, I_STR, PARSEIOC_GETFMT): %m", CLK_UNIT(parse->peer)); return 0; } return 1; } /*-------------------------------------------------- * STREAM setfmt */ static int stream_setfmt( struct parseunit *parse, parsectl_t *tcl ) { struct strioctl strioc; strioc.ic_cmd = PARSEIOC_SETFMT; strioc.ic_timout = 0; strioc.ic_dp = (char *)tcl; strioc.ic_len = sizeof (*tcl); if (ioctl(parse->generic->io.fd, I_STR, (caddr_t)&strioc) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: stream_setfmt: ioctl(fd, I_STR, PARSEIOC_SETFMT): %m", CLK_UNIT(parse->peer)); return 0; } return 1; } /*-------------------------------------------------- * STREAM timecode */ static int stream_timecode( struct parseunit *parse, parsectl_t *tcl ) { struct strioctl strioc; strioc.ic_cmd = PARSEIOC_TIMECODE; strioc.ic_timout = 0; strioc.ic_dp = (char *)tcl; strioc.ic_len = sizeof (*tcl); if (ioctl(parse->generic->io.fd, I_STR, (caddr_t)&strioc) == -1) { ERR(ERR_INTERNAL) msyslog(LOG_ERR, "PARSE receiver #%d: stream_timecode: ioctl(fd, I_STR, PARSEIOC_TIMECODE): %m", CLK_UNIT(parse->peer)); return 0; } clear_err(parse, ERR_INTERNAL); return 1; } /*-------------------------------------------------- * STREAM receive */ static void stream_receive( struct recvbuf *rbufp ) { struct parseunit *parse = (struct parseunit *)((void *)rbufp->recv_srcclock); parsetime_t parsetime; if (!parse->peer) return; if (rbufp->recv_length != sizeof(parsetime_t)) { ERR(ERR_BADIO) msyslog(LOG_ERR,"PARSE receiver #%d: stream_receive: bad size (got %d expected %d)", CLK_UNIT(parse->peer), rbufp->recv_length, (int)sizeof(parsetime_t)); parse->generic->baddata++; parse_event(parse, CEVNT_BADREPLY); return; } clear_err(parse, ERR_BADIO); memmove((caddr_t)&parsetime, (caddr_t)rbufp->recv_buffer, sizeof(parsetime_t)); #ifdef DEBUG if (debug > 3) { printf("PARSE receiver #%d: status %06x, state %08x, time %lx.%08lx, stime %lx.%08lx, ptime %lx.%08lx\n", CLK_UNIT(parse->peer), (unsigned int)parsetime.parse_status, (unsigned int)parsetime.parse_state, (long)parsetime.parse_time.tv.tv_sec, (long)parsetime.parse_time.tv.tv_usec, (long)parsetime.parse_stime.tv.tv_sec, (long)parsetime.parse_stime.tv.tv_usec, (long)parsetime.parse_ptime.tv.tv_sec, (long)parsetime.parse_ptime.tv.tv_usec); } #endif /* * switch time stamp world - be sure to normalize small usec field * errors. */ cvt_ts(parsetime.parse_stime, "parse_stime"); if (PARSE_TIMECODE(parsetime.parse_state)) { cvt_ts(parsetime.parse_time, "parse_time"); } if (PARSE_PPS(parsetime.parse_state)) cvt_ts(parsetime.parse_ptime, "parse_ptime"); parse_process(parse, &parsetime); } #endif /*-------------------------------------------------- * local init */ static int local_init( struct parseunit *parse ) { return parse_ioinit(&parse->parseio); } /*-------------------------------------------------- * local end */ static void local_end( struct parseunit *parse ) { parse_ioend(&parse->parseio); } /*-------------------------------------------------- * local nop */ static int local_nop( struct parseunit *parse ) { return 1; } /*-------------------------------------------------- * local setcs */ static int local_setcs( struct parseunit *parse, parsectl_t *tcl ) { return parse_setcs(tcl, &parse->parseio); } /*-------------------------------------------------- * local getfmt */ static int local_getfmt( struct parseunit *parse, parsectl_t *tcl ) { return parse_getfmt(tcl, &parse->parseio); } /*-------------------------------------------------- * local setfmt */ static int local_setfmt( struct parseunit *parse, parsectl_t *tcl ) { return parse_setfmt(tcl, &parse->parseio); } /*-------------------------------------------------- * local timecode */ static int local_timecode( struct parseunit *parse, parsectl_t *tcl ) { return parse_timecode(tcl, &parse->parseio); } /*-------------------------------------------------- * local input */ static int local_input( struct recvbuf *rbufp ) { struct parseunit *parse = (struct parseunit *)((void *)rbufp->recv_srcclock); int count; unsigned char *s; timestamp_t ts; if (!parse->peer) return 0; /* * eat all characters, parsing then and feeding complete samples */ count = rbufp->recv_length; s = (unsigned char *)rbufp->recv_buffer; ts.fp = rbufp->recv_time; while (count--) { if (parse_ioread(&parse->parseio, (unsigned int)(*s++), &ts)) { struct recvbuf buf; /* * got something good to eat */ if (!PARSE_PPS(parse->parseio.parse_dtime.parse_state)) { #ifdef TIOCDCDTIMESTAMP struct timeval dcd_time; if (ioctl(rbufp->fd, TIOCDCDTIMESTAMP, &dcd_time) != -1) { l_fp tstmp; TVTOTS(&dcd_time, &tstmp); tstmp.l_ui += JAN_1970; L_SUB(&ts.fp, &tstmp); if (ts.fp.l_ui == 0) { #ifdef DEBUG if (debug) { printf( "parse: local_receive: fd %d DCDTIMESTAMP %s\n", rbufp->fd, lfptoa(&tstmp, 6)); printf(" sigio %s\n", lfptoa(&ts.fp, 6)); } #endif parse->parseio.parse_dtime.parse_ptime.fp = tstmp; parse->parseio.parse_dtime.parse_state |= PARSEB_PPS|PARSEB_S_PPS; } } #else /* TIOCDCDTIMESTAMP */ #if defined(HAVE_STRUCT_PPSCLOCKEV) && (defined(HAVE_CIOGETEV) || defined(HAVE_TIOCGPPSEV)) if (parse->flags & PARSE_PPSCLOCK) { l_fp tts; struct ppsclockev ev; #ifdef HAVE_CIOGETEV if (ioctl(parse->generic->io.fd, CIOGETEV, (caddr_t)&ev) == 0) #endif #ifdef HAVE_TIOCGPPSEV if (ioctl(parse->generic->io.fd, TIOCGPPSEV, (caddr_t)&ev) == 0) #endif { if (ev.serial != parse->ppsserial) { /* * add PPS time stamp if available via ppsclock module * and not supplied already. */ if (!buftvtots((const char *)&ev.tv, &tts)) { ERR(ERR_BADDATA) msyslog(LOG_ERR,"parse: local_receive: timestamp conversion error (buftvtots) (ppsclockev.tv)"); } else { parse->parseio.parse_dtime.parse_ptime.fp = tts; parse->parseio.parse_dtime.parse_state |= PARSEB_PPS|PARSEB_S_PPS; } } parse->ppsserial = ev.serial; } } #endif #endif /* TIOCDCDTIMESTAMP */ } if (count) { /* simulate receive */ memmove((caddr_t)buf.recv_buffer, (caddr_t)&parse->parseio.parse_dtime, sizeof(parsetime_t)); parse_iodone(&parse->parseio); buf.recv_length = sizeof(parsetime_t); buf.recv_time = rbufp->recv_time; buf.srcadr = rbufp->srcadr; buf.dstadr = rbufp->dstadr; buf.fd = rbufp->fd; buf.next = 0; buf.X_from_where = rbufp->X_from_where; rbufp->receiver(&buf); } else { memmove((caddr_t)rbufp->recv_buffer, (caddr_t)&parse->parseio.parse_dtime, sizeof(parsetime_t)); parse_iodone(&parse->parseio); rbufp->recv_length = sizeof(parsetime_t); return 1; /* got something & in place return */ } } } return 0; /* nothing to pass up */ } /*-------------------------------------------------- * local receive */ static void local_receive( struct recvbuf *rbufp ) { struct parseunit *parse = (struct parseunit *)((void *)rbufp->recv_srcclock); parsetime_t parsetime; if (!parse->peer) return; if (rbufp->recv_length != sizeof(parsetime_t)) { ERR(ERR_BADIO) msyslog(LOG_ERR,"PARSE receiver #%d: local_receive: bad size (got %d expected %d)", CLK_UNIT(parse->peer), rbufp->recv_length, (int)sizeof(parsetime_t)); parse->generic->baddata++; parse_event(parse, CEVNT_BADREPLY); return; } clear_err(parse, ERR_BADIO); memmove((caddr_t)&parsetime, (caddr_t)rbufp->recv_buffer, sizeof(parsetime_t)); #ifdef DEBUG if (debug > 3) { printf("PARSE receiver #%d: status %06x, state %08x, time %lx.%08lx, stime %lx.%08lx, ptime %lx.%08lx\n", CLK_UNIT(parse->peer), (unsigned int)parsetime.parse_status, (unsigned int)parsetime.parse_state, (long)parsetime.parse_time.tv.tv_sec, (long)parsetime.parse_time.tv.tv_usec, (long)parsetime.parse_stime.tv.tv_sec, (long)parsetime.parse_stime.tv.tv_usec, (long)parsetime.parse_ptime.tv.tv_sec, (long)parsetime.parse_ptime.tv.tv_usec); } #endif parse_process(parse, &parsetime); } /*-------------------------------------------------- * init_iobinding - find and initialize lower layers */ static bind_t * init_iobinding( struct parseunit *parse ) { bind_t *b = io_bindings; while (b->bd_description != (char *)0) { if ((*b->bd_init)(parse)) { return b; } b++; } return (bind_t *)0; } /**=========================================================================== ** support routines **/ /*-------------------------------------------------- * convert a flag field to a string */ static char * parsestate( u_long lstate, char *buffer ) { static struct bits { u_long bit; const char *name; } flagstrings[] = { { PARSEB_ANNOUNCE, "DST SWITCH WARNING" }, { PARSEB_POWERUP, "NOT SYNCHRONIZED" }, { PARSEB_NOSYNC, "TIME CODE NOT CONFIRMED" }, { PARSEB_DST, "DST" }, { PARSEB_UTC, "UTC DISPLAY" }, { PARSEB_LEAPADD, "LEAP ADD WARNING" }, { PARSEB_LEAPDEL, "LEAP DELETE WARNING" }, { PARSEB_LEAPSECOND, "LEAP SECOND" }, { PARSEB_ALTERNATE, "ALTERNATE ANTENNA" }, { PARSEB_TIMECODE, "TIME CODE" }, { PARSEB_PPS, "PPS" }, { PARSEB_POSITION, "POSITION" }, { 0 } }; static struct sbits { u_long bit; const char *name; } sflagstrings[] = { { PARSEB_S_LEAP, "LEAP INDICATION" }, { PARSEB_S_PPS, "PPS SIGNAL" }, { PARSEB_S_ANTENNA, "ANTENNA" }, { PARSEB_S_POSITION, "POSITION" }, { 0 } }; int i; *buffer = '\0'; i = 0; while (flagstrings[i].bit) { if (flagstrings[i].bit & lstate) { if (buffer[0]) strcat(buffer, "; "); strcat(buffer, flagstrings[i].name); } i++; } if (lstate & (PARSEB_S_LEAP|PARSEB_S_ANTENNA|PARSEB_S_PPS|PARSEB_S_POSITION)) { char *s, *t; if (buffer[0]) strcat(buffer, "; "); strcat(buffer, "("); t = s = buffer + strlen(buffer); i = 0; while (sflagstrings[i].bit) { if (sflagstrings[i].bit & lstate) { if (t != s) { strcpy(t, "; "); t += 2; } strcpy(t, sflagstrings[i].name); t += strlen(t); } i++; } strcpy(t, ")"); } return buffer; } /*-------------------------------------------------- * convert a status flag field to a string */ static char * parsestatus( u_long lstate, char *buffer ) { static struct bits { u_long bit; const char *name; } flagstrings[] = { { CVT_OK, "CONVERSION SUCCESSFUL" }, { CVT_NONE, "NO CONVERSION" }, { CVT_FAIL, "CONVERSION FAILED" }, { CVT_BADFMT, "ILLEGAL FORMAT" }, { CVT_BADDATE, "DATE ILLEGAL" }, { CVT_BADTIME, "TIME ILLEGAL" }, { CVT_ADDITIONAL, "ADDITIONAL DATA" }, { 0 } }; int i; *buffer = '\0'; i = 0; while (flagstrings[i].bit) { if (flagstrings[i].bit & lstate) { if (buffer[0]) strcat(buffer, "; "); strcat(buffer, flagstrings[i].name); } i++; } return buffer; } /*-------------------------------------------------- * convert a clock status flag field to a string */ static const char * clockstatus( u_long lstate ) { static char buffer[20]; static struct status { u_long value; const char *name; } flagstrings[] = { { CEVNT_NOMINAL, "NOMINAL" }, { CEVNT_TIMEOUT, "NO RESPONSE" }, { CEVNT_BADREPLY,"BAD FORMAT" }, { CEVNT_FAULT, "FAULT" }, { CEVNT_PROP, "PROPAGATION DELAY" }, { CEVNT_BADDATE, "ILLEGAL DATE" }, { CEVNT_BADTIME, "ILLEGAL TIME" }, { (unsigned)~0L } }; int i; i = 0; while (flagstrings[i].value != ~0) { if (flagstrings[i].value == lstate) { return flagstrings[i].name; } i++; } sprintf(buffer, "unknown #%ld", (u_long)lstate); return buffer; } /*-------------------------------------------------- * l_mktime - make representation of a relative time */ static char * l_mktime( u_long delta ) { u_long tmp, m, s; static char buffer[40]; buffer[0] = '\0'; if ((tmp = delta / (60*60*24)) != 0) { sprintf(buffer, "%ldd+", (u_long)tmp); delta -= tmp * 60*60*24; } s = delta % 60; delta /= 60; m = delta % 60; delta /= 60; sprintf(buffer+strlen(buffer), "%02d:%02d:%02d", (int)delta, (int)m, (int)s); return buffer; } /*-------------------------------------------------- * parse_statistics - list summary of clock states */ static void parse_statistics( struct parseunit *parse ) { int i; NLOG(NLOG_CLOCKSTATIST) /* conditional if clause for conditional syslog */ { msyslog(LOG_INFO, "PARSE receiver #%d: running time: %s", CLK_UNIT(parse->peer), l_mktime(current_time - parse->generic->timestarted)); msyslog(LOG_INFO, "PARSE receiver #%d: current status: %s", CLK_UNIT(parse->peer), clockstatus(parse->generic->currentstatus)); for (i = 0; i <= CEVNT_MAX; i++) { u_long s_time; u_long percent, d = current_time - parse->generic->timestarted; percent = s_time = PARSE_STATETIME(parse, i); while (((u_long)(~0) / 10000) < percent) { percent /= 10; d /= 10; } if (d) percent = (percent * 10000) / d; else percent = 10000; if (s_time) msyslog(LOG_INFO, "PARSE receiver #%d: state %18s: %13s (%3ld.%02ld%%)", CLK_UNIT(parse->peer), clockstatus((unsigned int)i), l_mktime(s_time), percent / 100, percent % 100); } } } /*-------------------------------------------------- * cparse_statistics - wrapper for statistics call */ static void cparse_statistics( register struct parseunit *parse ) { if (parse->laststatistic + PARSESTATISTICS < current_time) parse_statistics(parse); parse->laststatistic = current_time; } /**=========================================================================== ** ntp interface routines **/ /*-------------------------------------------------- * parse_init - initialize internal parse driver data */ static void parse_init(void) { memset((caddr_t)parseunits, 0, sizeof parseunits); } /*-------------------------------------------------- * parse_shutdown - shut down a PARSE clock */ static void parse_shutdown( int unit, struct peer *peer ) { struct parseunit *parse = (struct parseunit *)peer->procptr->unitptr; if (parse && !parse->peer) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_shutdown: INTERNAL ERROR, unit not in use", unit); return; } /* * print statistics a last time and * stop statistics machine */ parse_statistics(parse); if (parse->parse_type->cl_end) { parse->parse_type->cl_end(parse); } if (parse->binding) PARSE_END(parse); /* * Tell the I/O module to turn us off. We're history. */ io_closeclock(&parse->generic->io); free_varlist(parse->kv); NLOG(NLOG_CLOCKINFO) /* conditional if clause for conditional syslog */ msyslog(LOG_INFO, "PARSE receiver #%d: reference clock \"%s\" removed", CLK_UNIT(parse->peer), parse->parse_type->cl_description); parse->peer = (struct peer *)0; /* unused now */ free(parse); } /*-------------------------------------------------- * parse_start - open the PARSE devices and initialize data for processing */ static int parse_start( int sysunit, struct peer *peer ) { u_int unit; int fd232; #ifdef HAVE_TERMIOS struct termios tio; /* NEEDED FOR A LONG TIME ! */ #endif #ifdef HAVE_SYSV_TTYS struct termio tio; /* NEEDED FOR A LONG TIME ! */ #endif struct parseunit * parse; char parsedev[sizeof(PARSEDEVICE)+20]; parsectl_t tmp_ctl; u_int type; type = CLK_TYPE(peer); unit = CLK_UNIT(peer); if ((type == ~0) || (parse_clockinfo[type].cl_description == (char *)0)) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: unsupported clock type %d (max %d)", unit, CLK_REALTYPE(peer), ncltypes-1); return 0; } /* * Unit okay, attempt to open the device. */ (void) sprintf(parsedev, PARSEDEVICE, unit); #ifndef O_NOCTTY #define O_NOCTTY 0 #endif fd232 = open(parsedev, O_RDWR | O_NOCTTY #ifdef O_NONBLOCK | O_NONBLOCK #endif , 0777); if (fd232 == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: open of %s failed: %m", unit, parsedev); return 0; } parse = (struct parseunit *)emalloc(sizeof(struct parseunit)); memset((char *)parse, 0, sizeof(struct parseunit)); parse->generic = peer->procptr; /* link up */ parse->generic->unitptr = (caddr_t)parse; /* link down */ /* * Set up the structures */ parse->generic->timestarted = current_time; parse->lastchange = current_time; parse->generic->currentstatus = CEVNT_TIMEOUT; /* expect the worst */ parse->flags = 0; parse->pollneeddata = 0; parse->laststatistic = current_time; parse->lastformat = (unsigned short)~0; /* assume no format known */ parse->time.parse_status = (unsigned short)~0; /* be sure to mark initial status change */ parse->lastmissed = 0; /* assume got everything */ parse->ppsserial = 0; parse->localdata = (void *)0; parse->localstate = 0; parse->kv = (struct ctl_var *)0; clear_err(parse, ERR_ALL); parse->parse_type = &parse_clockinfo[type]; parse->generic->fudgetime1 = parse->parse_type->cl_basedelay; parse->generic->fudgetime2 = 0.0; parse->generic->clockdesc = parse->parse_type->cl_description; peer->rootdelay = parse->parse_type->cl_rootdelay; peer->sstclktype = parse->parse_type->cl_type; peer->precision = sys_precision; peer->stratum = STRATUM_REFCLOCK; if (peer->stratum <= 1) memmove((char *)&parse->generic->refid, parse->parse_type->cl_id, 4); else parse->generic->refid = htonl(PARSEHSREFID); parse->generic->io.fd = fd232; parse->peer = peer; /* marks it also as busy */ /* * configure terminal line */ if (TTY_GETATTR(fd232, &tio) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: tcgetattr(%d, &tio): %m", unit, fd232); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; } else { #ifndef _PC_VDISABLE memset((char *)tio.c_cc, 0, sizeof(tio.c_cc)); #else int disablec; errno = 0; /* pathconf can deliver -1 without changing errno ! */ disablec = fpathconf(parse->generic->io.fd, _PC_VDISABLE); if (disablec == -1 && errno) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: fpathconf(fd, _PC_VDISABLE): %m", CLK_UNIT(parse->peer)); memset((char *)tio.c_cc, 0, sizeof(tio.c_cc)); /* best guess */ } else if (disablec != -1) memset((char *)tio.c_cc, disablec, sizeof(tio.c_cc)); #endif #if defined (VMIN) || defined(VTIME) if ((parse_clockinfo[type].cl_lflag & ICANON) == 0) { #ifdef VMIN tio.c_cc[VMIN] = 1; #endif #ifdef VTIME tio.c_cc[VTIME] = 0; #endif } #endif tio.c_cflag = parse_clockinfo[type].cl_cflag; tio.c_iflag = parse_clockinfo[type].cl_iflag; tio.c_oflag = parse_clockinfo[type].cl_oflag; tio.c_lflag = parse_clockinfo[type].cl_lflag; #ifdef HAVE_TERMIOS if ((cfsetospeed(&tio, parse_clockinfo[type].cl_speed) == -1) || (cfsetispeed(&tio, parse_clockinfo[type].cl_speed) == -1)) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: tcset{i,o}speed(&tio, speed): %m", unit); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; } #else tio.c_cflag |= parse_clockinfo[type].cl_speed; #endif #if defined(HAVE_TIO_SERIAL_STUFF) /* Linux hack: define PPS interface */ { struct serial_struct ss; if (ioctl(fd232, TIOCGSERIAL, &ss) < 0 || ( #ifdef ASYNC_LOW_LATENCY ss.flags |= ASYNC_LOW_LATENCY, #endif #ifdef ASYNC_PPS_CD_NEG ss.flags |= ASYNC_PPS_CD_NEG, #endif ioctl(fd232, TIOCSSERIAL, &ss)) < 0) { msyslog(LOG_NOTICE, "refclock_parse: TIOCSSERIAL fd %d, %m", fd232); msyslog(LOG_NOTICE, "refclock_parse: optional PPS processing not available"); } else { parse->flags |= PARSE_PPSCLOCK; msyslog(LOG_INFO, "refclock_parse: PPS detection on"); } } #endif #ifdef HAVE_TIOCSPPS /* SUN PPS support */ if (CLK_PPS(parse->peer)) { int i = 1; if (ioctl(fd232, TIOCSPPS, (caddr_t)&i) == 0) { parse->flags |= PARSE_PPSCLOCK; } } #endif if (TTY_SETATTR(fd232, &tio) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: tcsetattr(%d, &tio): %m", unit, fd232); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; } } /* * Insert in async io device list. */ parse->generic->io.srcclock = (caddr_t)parse; parse->generic->io.datalen = 0; if (!io_addclock(&parse->generic->io)) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: addclock %s fails (ABORT - clock type requires async io)", CLK_UNIT(parse->peer), parsedev); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; } parse->binding = init_iobinding(parse); parse->generic->io.clock_recv = parse->binding->bd_receive; /* pick correct receive routine */ parse->generic->io.io_input = parse->binding->bd_io_input; /* pick correct input routine */ if (parse->binding == (bind_t *)0) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: io sub system initialisation failed.", CLK_UNIT(parse->peer)); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; /* well, ok - special initialisation broke */ } /* * as we always(?) get 8 bit chars we want to be * sure, that the upper bits are zero for less * than 8 bit I/O - so we pass that information on. * note that there can be only one bit count format * per file descriptor */ switch (tio.c_cflag & CSIZE) { case CS5: tmp_ctl.parsesetcs.parse_cs = PARSE_IO_CS5; break; case CS6: tmp_ctl.parsesetcs.parse_cs = PARSE_IO_CS6; break; case CS7: tmp_ctl.parsesetcs.parse_cs = PARSE_IO_CS7; break; case CS8: tmp_ctl.parsesetcs.parse_cs = PARSE_IO_CS8; break; } if (!PARSE_SETCS(parse, &tmp_ctl)) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: parse_setcs() FAILED.", unit); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; /* well, ok - special initialisation broke */ } strcpy(tmp_ctl.parseformat.parse_buffer, parse->parse_type->cl_format); tmp_ctl.parseformat.parse_count = strlen(tmp_ctl.parseformat.parse_buffer); if (!PARSE_SETFMT(parse, &tmp_ctl)) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_start: parse_setfmt() FAILED.", unit); parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; /* well, ok - special initialisation broke */ } /* * get rid of all IO accumulated so far */ #ifdef HAVE_TERMIOS (void) tcflush(parse->generic->io.fd, TCIOFLUSH); #else #ifdef TCFLSH { #ifndef TCIOFLUSH #define TCIOFLUSH 2 #endif int flshcmd = TCIOFLUSH; (void) ioctl(parse->generic->io.fd, TCFLSH, (caddr_t)&flshcmd); } #endif #endif /* * try to do any special initializations */ if (parse->parse_type->cl_init) { if (parse->parse_type->cl_init(parse)) { parse_shutdown(CLK_UNIT(parse->peer), peer); /* let our cleaning staff do the work */ return 0; /* well, ok - special initialisation broke */ } } /* * get out Copyright information once */ if (!notice) { NLOG(NLOG_CLOCKINFO) /* conditional if clause for conditional syslog */ msyslog(LOG_INFO, "NTP PARSE support: Copyright (c) 1989-1999, Frank Kardel"); notice = 1; } /* * print out configuration */ NLOG(NLOG_CLOCKINFO) { /* conditional if clause for conditional syslog */ msyslog(LOG_INFO, "PARSE receiver #%d: reference clock \"%s\" (device %s) added", CLK_UNIT(parse->peer), parse->parse_type->cl_description, parsedev); msyslog(LOG_INFO, "PARSE receiver #%d: Stratum %d, %sPPS support, trust time %s, precision %d", CLK_UNIT(parse->peer), parse->peer->stratum, CLK_PPS(parse->peer) ? "" : "no ", l_mktime(parse->parse_type->cl_maxunsync), parse->peer->precision); msyslog(LOG_INFO, "PARSE receiver #%d: rootdelay %.6f s, phaseadjust %.6f s, %s IO handling", CLK_UNIT(parse->peer), parse->parse_type->cl_rootdelay, parse->generic->fudgetime1, parse->binding->bd_description); msyslog(LOG_INFO, "PARSE receiver #%d: Format recognition: %s", CLK_UNIT(parse->peer), parse->parse_type->cl_format); #ifdef PPS msyslog(LOG_INFO, "PARSE receiver #%d: %sPPS ioctl support", CLK_UNIT(parse->peer), (parse->flags & PARSE_PPSCLOCK) ? "" : "NO "); #endif } return 1; } /*-------------------------------------------------- * parse_poll - called by the transmit procedure */ static void parse_poll( int unit, struct peer *peer ) { struct parseunit *parse = (struct parseunit *)peer->procptr->unitptr; if (peer != parse->peer) { msyslog(LOG_ERR, "PARSE receiver #%d: poll: INTERNAL: peer incorrect", unit); return; } /* * Update clock stat counters */ parse->generic->polls++; if (parse->pollneeddata && ((current_time - parse->pollneeddata) > (1<<(max(min(parse->peer->hpoll, parse->peer->ppoll), parse->peer->minpoll))))) { /* * start worrying when exceeding a poll inteval * bad news - didn't get a response last time */ parse->generic->noreply++; parse->lastmissed = current_time; parse_event(parse, CEVNT_TIMEOUT); ERR(ERR_NODATA) msyslog(LOG_WARNING, "PARSE receiver #%d: no data from device within poll interval (check receiver / cableling)", CLK_UNIT(parse->peer)); } /* * we just mark that we want the next sample for the clock filter */ parse->pollneeddata = current_time; if (parse->parse_type->cl_poll) { parse->parse_type->cl_poll(parse); } cparse_statistics(parse); return; } #define LEN_STATES 300 /* length of state string */ /*-------------------------------------------------- * parse_control - set fudge factors, return statistics */ static void parse_control( int unit, struct refclockstat *in, struct refclockstat *out, struct peer *peer ) { register struct parseunit *parse = (struct parseunit *)peer->procptr->unitptr; parsectl_t tmpctl; static char outstatus[400]; /* status output buffer */ if (out) { out->lencode = 0; out->p_lastcode = 0; out->kv_list = (struct ctl_var *)0; } if (!parse || !parse->peer) { msyslog(LOG_ERR, "PARSE receiver #%d: parse_control: unit invalid (UNIT INACTIVE)", unit); return; } unit = CLK_UNIT(parse->peer); if (in) { if (in->haveflags & (CLK_HAVEFLAG1|CLK_HAVEFLAG2|CLK_HAVEFLAG3|CLK_HAVEFLAG4)) { parse->flags = in->flags & (CLK_FLAG1|CLK_FLAG2|CLK_FLAG3|CLK_FLAG4); } } if (out) { u_long sum = 0; char *t, *tt, *start; int i; outstatus[0] = '\0'; out->type = REFCLK_PARSE; out->haveflags |= CLK_HAVETIME2; /* * figure out skew between PPS and RS232 - just for informational * purposes - returned in time2 value */ if (PARSE_SYNC(parse->time.parse_state)) { if (PARSE_PPS(parse->time.parse_state) && PARSE_TIMECODE(parse->time.parse_state)) { l_fp off; /* * we have a PPS and RS232 signal - calculate the skew * WARNING: assumes on TIMECODE == PULSE (timecode after pulse) */ off = parse->time.parse_stime.fp; L_SUB(&off, &parse->time.parse_ptime.fp); /* true offset */ tt = add_var(&out->kv_list, 80, RO); sprintf(tt, "refclock_ppsskew=%s", lfptoms(&off, 6)); } } if (PARSE_PPS(parse->time.parse_state)) { tt = add_var(&out->kv_list, 80, RO|DEF); sprintf(tt, "refclock_ppstime=\"%s\"", gmprettydate(&parse->time.parse_ptime.fp)); } tt = add_var(&out->kv_list, 128, RO|DEF); sprintf(tt, "refclock_time=\""); tt += strlen(tt); if (parse->time.parse_time.fp.l_ui == 0) { strcpy(tt, "\""); } else { sprintf(tt, "%s\"", gmprettydate(&parse->time.parse_time.fp)); t = tt + strlen(tt); } if (!PARSE_GETTIMECODE(parse, &tmpctl)) { ERR(ERR_INTERNAL) msyslog(LOG_ERR, "PARSE receiver #%d: parse_control: parse_timecode() FAILED", unit); } else { tt = add_var(&out->kv_list, 512, RO|DEF); sprintf(tt, "refclock_status=\""); tt += strlen(tt); /* * copy PPS flags from last read transaction (informational only) */ tmpctl.parsegettc.parse_state |= parse->time.parse_state & (PARSEB_PPS|PARSEB_S_PPS); (void) parsestate(tmpctl.parsegettc.parse_state, tt); strcat(tt, "\""); if (tmpctl.parsegettc.parse_count) mkascii(outstatus+strlen(outstatus), (int)(sizeof(outstatus)- strlen(outstatus) - 1), tmpctl.parsegettc.parse_buffer, (unsigned)(tmpctl.parsegettc.parse_count - 1)); parse->generic->badformat += tmpctl.parsegettc.parse_badformat; } tmpctl.parseformat.parse_format = tmpctl.parsegettc.parse_format; if (!PARSE_GETFMT(parse, &tmpctl)) { ERR(ERR_INTERNAL) msyslog(LOG_ERR, "PARSE receiver #%d: parse_control: parse_getfmt() FAILED", unit); } else { tt = add_var(&out->kv_list, 80, RO|DEF); sprintf(tt, "refclock_format=\""); strncat(tt, tmpctl.parseformat.parse_buffer, tmpctl.parseformat.parse_count); strcat(tt,"\""); } /* * gather state statistics */ start = tt = add_var(&out->kv_list, LEN_STATES, RO|DEF); strcpy(tt, "refclock_states=\""); tt += strlen(tt); for (i = 0; i <= CEVNT_MAX; i++) { u_long s_time; u_long d = current_time - parse->generic->timestarted; u_long percent; percent = s_time = PARSE_STATETIME(parse, i); while (((u_long)(~0) / 10000) < percent) { percent /= 10; d /= 10; } if (d) percent = (percent * 10000) / d; else percent = 10000; if (s_time) { char item[80]; int count; sprintf(item, "%s%s%s: %s (%d.%02d%%)", sum ? "; " : "", (parse->generic->currentstatus == i) ? "*" : "", clockstatus((unsigned int)i), l_mktime(s_time), (int)(percent / 100), (int)(percent % 100)); if ((count = strlen(item)) < (LEN_STATES - 40 - (tt - start))) { strcpy(tt, item); tt += count; } sum += s_time; } } sprintf(tt, "; running time: %s\"", l_mktime(sum)); tt = add_var(&out->kv_list, 32, RO); sprintf(tt, "refclock_id=\"%s\"", parse->parse_type->cl_id); tt = add_var(&out->kv_list, 80, RO); sprintf(tt, "refclock_iomode=\"%s\"", parse->binding->bd_description); tt = add_var(&out->kv_list, 128, RO); sprintf(tt, "refclock_driver_version=\"%s\"", rcsid); { struct ctl_var *k; k = parse->kv; while (k && !(k->flags & EOV)) { set_var(&out->kv_list, k->text, strlen(k->text)+1, k->flags); k++; } } out->lencode = strlen(outstatus); out->p_lastcode = outstatus; } } /**=========================================================================== ** processing routines **/ /*-------------------------------------------------- * event handling - note that nominal events will also be posted */ static void parse_event( struct parseunit *parse, int event ) { if (parse->generic->currentstatus != (u_char) event) { parse->statetime[parse->generic->currentstatus] += current_time - parse->lastchange; parse->lastchange = current_time; parse->generic->currentstatus = (u_char)event; if (parse->parse_type->cl_event) parse->parse_type->cl_event(parse, event); if (event != CEVNT_NOMINAL) { parse->generic->lastevent = parse->generic->currentstatus; } else { NLOG(NLOG_CLOCKSTATUS) msyslog(LOG_INFO, "PARSE receiver #%d: SYNCHRONIZED", CLK_UNIT(parse->peer)); } if (event == CEVNT_FAULT) { NLOG(NLOG_CLOCKEVENT) /* conditional if clause for conditional syslog */ ERR(ERR_BADEVENT) msyslog(LOG_ERR, "clock %s fault '%s' (0x%02x)", refnumtoa(&parse->peer->srcadr), ceventstr(event), (u_int)event); } else { NLOG(NLOG_CLOCKEVENT) /* conditional if clause for conditional syslog */ if (event == CEVNT_NOMINAL || list_err(parse, ERR_BADEVENT)) msyslog(LOG_INFO, "clock %s event '%s' (0x%02x)", refnumtoa(&parse->peer->srcadr), ceventstr(event), (u_int)event); } report_event(EVNT_PEERCLOCK, parse->peer); report_event(EVNT_CLOCKEXCPT, parse->peer); } } /*-------------------------------------------------- * process a PARSE time sample */ static void parse_process( struct parseunit *parse, parsetime_t *parsetime ) { l_fp off, rectime, reftime; double fudge; /* * check for changes in conversion status * (only one for each new status !) */ if (((parsetime->parse_status & CVT_MASK) != CVT_OK) && ((parsetime->parse_status & CVT_MASK) != CVT_NONE) && (parse->time.parse_status != parsetime->parse_status)) { char buffer[400]; NLOG(NLOG_CLOCKINFO) /* conditional if clause for conditional syslog */ msyslog(LOG_WARNING, "PARSE receiver #%d: conversion status \"%s\"", CLK_UNIT(parse->peer), parsestatus(parsetime->parse_status, buffer)); if ((parsetime->parse_status & CVT_MASK) == CVT_FAIL) { /* * tell more about the story - list time code * there is a slight change for a race condition and * the time code might be overwritten by the next packet */ parsectl_t tmpctl; if (!PARSE_GETTIMECODE(parse, &tmpctl)) { ERR(ERR_INTERNAL) msyslog(LOG_ERR, "PARSE receiver #%d: parse_process: parse_timecode() FAILED", CLK_UNIT(parse->peer)); } else { ERR(ERR_BADDATA) msyslog(LOG_WARNING, "PARSE receiver #%d: FAILED TIMECODE: \"%s\" (check receiver configuration / cableling)", CLK_UNIT(parse->peer), mkascii(buffer, sizeof buffer, tmpctl.parsegettc.parse_buffer, (unsigned)(tmpctl.parsegettc.parse_count - 1))); parse->generic->badformat += tmpctl.parsegettc.parse_badformat; } } } /* * examine status and post appropriate events */ if ((parsetime->parse_status & CVT_MASK) != CVT_OK) { /* * got bad data - tell the rest of the system */ switch (parsetime->parse_status & CVT_MASK) { case CVT_NONE: if ((parsetime->parse_status & CVT_ADDITIONAL) && parse->parse_type->cl_message) parse->parse_type->cl_message(parse, parsetime); break; /* well, still waiting - timeout is handled at higher levels */ case CVT_FAIL: parse->generic->badformat++; if (parsetime->parse_status & CVT_BADFMT) { parse_event(parse, CEVNT_BADREPLY); } else if (parsetime->parse_status & CVT_BADDATE) { parse_event(parse, CEVNT_BADDATE); } else if (parsetime->parse_status & CVT_BADTIME) { parse_event(parse, CEVNT_BADTIME); } else { parse_event(parse, CEVNT_BADREPLY); /* for the lack of something better */ } } return; /* skip the rest - useless */ } /* * check for format changes * (in case somebody has swapped clocks 8-) */ if (parse->lastformat != parsetime->parse_format) { parsectl_t tmpctl; tmpctl.parseformat.parse_format = parsetime->parse_format; if (!PARSE_GETFMT(parse, &tmpctl)) { ERR(ERR_INTERNAL) msyslog(LOG_ERR, "PARSE receiver #%d: parse_getfmt() FAILED", CLK_UNIT(parse->peer)); } else { NLOG(NLOG_CLOCKINFO) /* conditional if clause for conditional syslog */ msyslog(LOG_INFO, "PARSE receiver #%d: packet format \"%s\"", CLK_UNIT(parse->peer), tmpctl.parseformat.parse_buffer); } parse->lastformat = parsetime->parse_format; } /* * now, any changes ? */ if (parse->time.parse_state != parsetime->parse_state) { char tmp1[200]; char tmp2[200]; /* * something happend */ (void) parsestate(parsetime->parse_state, tmp1); (void) parsestate(parse->time.parse_state, tmp2); NLOG(NLOG_CLOCKINFO) /* conditional if clause for conditional syslog */ msyslog(LOG_INFO,"PARSE receiver #%d: STATE CHANGE: %s -> %s", CLK_UNIT(parse->peer), tmp2, tmp1); } /* * remember for future */ parse->time = *parsetime; /* * check to see, whether the clock did a complete powerup or lost PZF signal * and post correct events for current condition */ if (PARSE_POWERUP(parsetime->parse_state)) { /* * this is bad, as we have completely lost synchronisation * well this is a problem with the receiver here * for PARSE Meinberg DCF77 receivers the lost synchronisation * is true as it is the powerup state and the time is taken * from a crude real time clock chip * for the PZF series this is only partly true, as * PARSE_POWERUP only means that the pseudo random * phase shift sequence cannot be found. this is only * bad, if we have never seen the clock in the SYNC * state, where the PHASE and EPOCH are correct. * for reporting events the above business does not * really matter, but we can use the time code * even in the POWERUP state after having seen * the clock in the synchronized state (PZF class * receivers) unless we have had a telegram disruption * after having seen the clock in the SYNC state. we * thus require having seen the clock in SYNC state * *after* having missed telegrams (noresponse) from * the clock. one problem remains: we might use erroneously * POWERUP data if the disruption is shorter than 1 polling * interval. fortunately powerdowns last usually longer than 64 * seconds and the receiver is at least 2 minutes in the * POWERUP or NOSYNC state before switching to SYNC */ parse_event(parse, CEVNT_FAULT); NLOG(NLOG_CLOCKSTATUS) ERR(ERR_BADSTATUS) msyslog(LOG_ERR,"PARSE receiver #%d: NOT SYNCHRONIZED", CLK_UNIT(parse->peer)); } else { /* * we have two states left * * SYNC: * this state means that the EPOCH (timecode) and PHASE * information has be read correctly (at least two * successive PARSE timecodes were received correctly) * this is the best possible state - full trust * * NOSYNC: * The clock should be on phase with respect to the second * signal, but the timecode has not been received correctly within * at least the last two minutes. this is a sort of half baked state * for PARSE Meinberg DCF77 clocks this is bad news (clock running * without timecode confirmation) * PZF 535 has also no time confirmation, but the phase should be * very precise as the PZF signal can be decoded */ if (PARSE_SYNC(parsetime->parse_state)) { /* * currently completely synchronized - best possible state */ parse->lastsync = current_time; clear_err(parse, ERR_BADSTATUS); } else { /* * we have had some problems receiving the time code */ parse_event(parse, CEVNT_PROP); NLOG(NLOG_CLOCKSTATUS) ERR(ERR_BADSTATUS) msyslog(LOG_ERR,"PARSE receiver #%d: TIMECODE NOT CONFIRMED", CLK_UNIT(parse->peer)); } } fudge = parse->generic->fudgetime1; /* standard RS232 Fudgefactor */ if (PARSE_TIMECODE(parsetime->parse_state)) { rectime = parsetime->parse_stime.fp; off = reftime = parsetime->parse_time.fp; L_SUB(&off, &rectime); /* prepare for PPS adjustments logic */ #ifdef DEBUG if (debug > 3) printf("PARSE receiver #%d: Reftime %s, Recvtime %s - initial offset %s\n", CLK_UNIT(parse->peer), prettydate(&reftime), prettydate(&rectime), lfptoa(&off,6)); #endif } if (PARSE_PPS(parsetime->parse_state) && CLK_PPS(parse->peer)) { l_fp offset; /* * we have a PPS signal - much better than the RS232 stuff (we hope) */ offset = parsetime->parse_ptime.fp; #ifdef DEBUG if (debug > 3) printf("PARSE receiver #%d: PPStime %s\n", CLK_UNIT(parse->peer), prettydate(&offset)); #endif if (PARSE_TIMECODE(parsetime->parse_state)) { if (M_ISGEQ(off.l_i, off.l_f, -1, 0x80000000) && M_ISGEQ(0, 0x7fffffff, off.l_i, off.l_f)) { fudge = parse->generic->fudgetime2; /* pick PPS fudge factor */ /* * RS232 offsets within [-0.5..0.5[ - take PPS offsets */ if (parse->parse_type->cl_flags & PARSE_F_PPSONSECOND) { reftime = off = offset; if (reftime.l_uf & (unsigned)0x80000000) reftime.l_ui++; reftime.l_uf = 0; /* * implied on second offset */ off.l_uf = ~off.l_uf; /* map [0.5..1[ -> [-0.5..0[ */ off.l_ui = (off.l_f < 0) ? ~0 : 0; /* sign extend */ } else { /* * time code describes pulse */ reftime = off = parsetime->parse_time.fp; L_SUB(&off, &offset); /* true offset */ } } /* * take RS232 offset when PPS when out of bounds */ } else { fudge = parse->generic->fudgetime2; /* pick PPS fudge factor */ /* * Well, no time code to guide us - assume on second pulse * and pray, that we are within [-0.5..0.5[ */ off = offset; reftime = offset; if (reftime.l_uf & (unsigned)0x80000000) reftime.l_ui++; reftime.l_uf = 0; /* * implied on second offset */ off.l_uf = ~off.l_uf; /* map [0.5..1[ -> [-0.5..0[ */ off.l_ui = (off.l_f < 0) ? ~0 : 0; /* sign extend */ } } else { if (!PARSE_TIMECODE(parsetime->parse_state)) { /* * Well, no PPS, no TIMECODE, no more work ... */ if ((parsetime->parse_status & CVT_ADDITIONAL) && parse->parse_type->cl_message) parse->parse_type->cl_message(parse, parsetime); return; } } #ifdef DEBUG if (debug > 3) printf("PARSE receiver #%d: Reftime %s, Recvtime %s - final offset %s\n", CLK_UNIT(parse->peer), prettydate(&reftime), prettydate(&rectime), lfptoa(&off,6)); #endif rectime = reftime; L_SUB(&rectime, &off); /* just to keep the ntp interface happy */ #ifdef DEBUG if (debug > 3) printf("PARSE receiver #%d: calculated Reftime %s, Recvtime %s\n", CLK_UNIT(parse->peer), prettydate(&reftime), prettydate(&rectime)); #endif if ((parsetime->parse_status & CVT_ADDITIONAL) && parse->parse_type->cl_message) parse->parse_type->cl_message(parse, parsetime); if (PARSE_SYNC(parsetime->parse_state)) { /* * log OK status */ parse_event(parse, CEVNT_NOMINAL); } clear_err(parse, ERR_BADIO); clear_err(parse, ERR_BADDATA); clear_err(parse, ERR_NODATA); clear_err(parse, ERR_INTERNAL); #ifdef DEBUG if (debug > 2) { printf("PARSE receiver #%d: refclock_process_offset(reftime=%s, rectime=%s, Fudge=%f)\n", CLK_UNIT(parse->peer), prettydate(&reftime), prettydate(&rectime), fudge); } #endif refclock_process_offset(parse->generic, reftime, rectime, fudge); if (PARSE_PPS(parsetime->parse_state) && CLK_PPS(parse->peer)) { (void) pps_sample(&parse->time.parse_ptime.fp); } /* * and now stick it into the clock machine * samples are only valid iff lastsync is not too old and * we have seen the clock in sync at least once * after the last time we didn't see an expected data telegram * see the clock states section above for more reasoning */ if (((current_time - parse->lastsync) > parse->parse_type->cl_maxunsync) || (parse->lastsync <= parse->lastmissed)) { parse->generic->leap = LEAP_NOTINSYNC; } else { if (PARSE_LEAPADD(parsetime->parse_state)) { /* * we pick this state also for time code that pass leap warnings * without direction information (as earth is currently slowing * down). */ parse->generic->leap = (parse->flags & PARSE_LEAP_DELETE) ? LEAP_DELSECOND : LEAP_ADDSECOND; } else if (PARSE_LEAPDEL(parsetime->parse_state)) { parse->generic->leap = LEAP_DELSECOND; } else { parse->generic->leap = LEAP_NOWARNING; } } /* * ready, unless the machine wants a sample */ if (!parse->pollneeddata) return; parse->pollneeddata = 0; refclock_receive(parse->peer); } /**=========================================================================== ** special code for special clocks **/ static void mk_utcinfo( char *t, int wnt, int wnlsf, int dn, int dtls, int dtlsf ) { l_fp leapdate; sprintf(t, "current correction %d sec", dtls); t += strlen(t); if (wnlsf < 990) wnlsf += 1024; if (wnt < 990) wnt += 1024; gpstolfp((unsigned short)wnlsf, (unsigned short)dn, 0, &leapdate); if ((dtlsf != dtls) && ((wnlsf - wnt) < 52)) { sprintf(t, ", next correction %d sec on %s, new GPS-UTC offset %d", dtlsf - dtls, gmprettydate(&leapdate), dtlsf); } else { sprintf(t, ", last correction on %s", gmprettydate(&leapdate)); } } #ifdef CLOCK_MEINBERG /**=========================================================================== ** Meinberg GPS166/GPS167 support **/ /*------------------------------------------------------------ * gps16x_message - process GPS16x messages */ static void gps16x_message( struct parseunit *parse, parsetime_t *parsetime ) { if (parse->time.parse_msglen && parsetime->parse_msg[0] == SOH) { GPS_MSG_HDR header; unsigned char *bufp = (unsigned char *)parsetime->parse_msg + 1; #ifdef DEBUG if (debug > 2) { char msgbuffer[600]; mkreadable(msgbuffer, sizeof(msgbuffer), (char *)parsetime->parse_msg, parsetime->parse_msglen, 1); printf("PARSE receiver #%d: received message (%d bytes) >%s<\n", CLK_UNIT(parse->peer), parsetime->parse_msglen, msgbuffer); } #endif get_mbg_header(&bufp, &header); if (header.gps_hdr_csum == mbg_csum(parsetime->parse_msg + 1, 6) && (header.gps_len == 0 || (header.gps_len < sizeof(parsetime->parse_msg) && header.gps_data_csum == mbg_csum(bufp, header.gps_len)))) { /* * clean message */ switch (header.gps_cmd) { case GPS_SW_REV: { char buffer[64]; SW_REV gps_sw_rev; get_mbg_sw_rev(&bufp, &gps_sw_rev); sprintf(buffer, "meinberg_gps_version=\"%x.%02x%s%s\"", (gps_sw_rev.code >> 8) & 0xFF, gps_sw_rev.code & 0xFF, gps_sw_rev.name[0] ? " " : "", gps_sw_rev.name); set_var(&parse->kv, buffer, 64, RO|DEF); } break; case GPS_STAT: { static struct state { unsigned short flag; /* status flag */ unsigned const char *string; /* bit name */ } states[] = { { TM_ANT_DISCONN, (const unsigned char *)"ANTENNA FAULTY" }, { TM_SYN_FLAG, (const unsigned char *)"NO SYNC SIGNAL" }, { TM_NO_SYNC, (const unsigned char *)"NO SYNC POWERUP" }, { TM_NO_POS, (const unsigned char *)"NO POSITION" }, { 0, (const unsigned char *)"" } }; unsigned short status; struct state *s = states; char buffer[512]; char *p, *b; status = get_lsb_short(&bufp); sprintf(buffer, "meinberg_gps_status=\"[0x%04x] ", status); if (status) { p = b = buffer + strlen(buffer); while (s->flag) { if (status & s->flag) { if (p != b) { *p++ = ','; *p++ = ' '; } strcat(p, (const char *)s->string); } s++; } *p++ = '"'; *p = '\0'; } else { strcat(buffer, "\""); } set_var(&parse->kv, buffer, 64, RO|DEF); } break; case GPS_POS_XYZ: { XYZ xyz; char buffer[256]; get_mbg_xyz(&bufp, xyz); sprintf(buffer, "gps_position(XYZ)=\"%s m, %s m, %s m\"", mfptoa(xyz[XP].l_ui, xyz[XP].l_uf, 1), mfptoa(xyz[YP].l_ui, xyz[YP].l_uf, 1), mfptoa(xyz[ZP].l_ui, xyz[ZP].l_uf, 1)); set_var(&parse->kv, buffer, sizeof(buffer), RO|DEF); } break; case GPS_POS_LLA: { LLA lla; char buffer[256]; get_mbg_lla(&bufp, lla); sprintf(buffer, "gps_position(LLA)=\"%s deg, %s deg, %s m\"", mfptoa(lla[LAT].l_ui, lla[LAT].l_uf, 4), mfptoa(lla[LON].l_ui, lla[LON].l_uf, 4), mfptoa(lla[ALT].l_ui, lla[ALT].l_uf, 1)); set_var(&parse->kv, buffer, sizeof(buffer), RO|DEF); } break; case GPS_TZDL: break; case GPS_PORT_PARM: break; case GPS_SYNTH: break; case GPS_ANT_INFO: { ANT_INFO antinfo; u_char buffer[512]; u_char *p; get_mbg_antinfo(&bufp, &antinfo); sprintf(buffer, "meinberg_antenna_status=\""); p = buffer + strlen(buffer); switch (antinfo.status) { case ANT_INVALID: strcat(p, ""); p += strlen(p); break; case ANT_DISCONN: strcat(p, "DISCONNECTED since "); NLOG(NLOG_CLOCKSTATUS) ERR(ERR_BADSTATUS) msyslog(LOG_ERR,"PARSE receiver #%d: ANTENNA FAILURE: %s", CLK_UNIT(parse->peer), p); p += strlen(p); mbg_tm_str(&p, &antinfo.tm_disconn); *p = '\0'; break; case ANT_RECONN: strcat(p, "RECONNECTED on "); p += strlen(p); mbg_tm_str(&p, &antinfo.tm_reconn); sprintf(p, ", reconnect clockoffset %c%ld.%07ld s, disconnect time ", (antinfo.delta_t < 0) ? '-' : '+', ABS(antinfo.delta_t) / 10000, ABS(antinfo.delta_t) % 10000); p += strlen(p); mbg_tm_str(&p, &antinfo.tm_disconn); *p = '\0'; break; default: sprintf(p, "bad status 0x%04x", antinfo.status); p += strlen(p); break; } *p++ = '"'; *p = '\0'; set_var(&parse->kv, buffer, sizeof(buffer), RO|DEF); } break; case GPS_UCAP: break; case GPS_CFGH: { CFGH cfgh; u_char buffer[512]; u_char *p; get_mbg_cfgh(&bufp, &cfgh); if (cfgh.valid) { int i; p = buffer; strcpy(buffer, "gps_tot_51=\""); p += strlen(p); mbg_tgps_str(&p, &cfgh.tot_51); *p++ = '"'; *p = '\0'; set_var(&parse->kv, buffer, sizeof(buffer), RO); p = buffer; strcpy(buffer, "gps_tot_63=\""); p += strlen(p); mbg_tgps_str(&p, &cfgh.tot_63); *p++ = '"'; *p = '\0'; set_var(&parse->kv, buffer, sizeof(buffer), RO); p = buffer; strcpy(buffer, "gps_t0a=\""); p += strlen(p); mbg_tgps_str(&p, &cfgh.t0a); *p++ = '"'; *p = '\0'; set_var(&parse->kv, buffer, sizeof(buffer), RO); for (i = MIN_SVNO; i <= MAX_SVNO; i++) { p = buffer; sprintf(p, "gps_cfg[%d]=\"[0x%x] ", i, cfgh.cfg[i]); p += strlen(p); switch (cfgh.cfg[i] & 0x7) { case 0: strcpy(p, "BLOCK I"); break; case 1: strcpy(p, "BLOCK II"); break; default: sprintf(p, "bad CFG"); break; } strcat(p, "\""); set_var(&parse->kv, buffer, sizeof(buffer), RO); p = buffer; sprintf(p, "gps_health[%d]=\"[0x%x] ", i, cfgh.health[i]); p += strlen(p); switch ((cfgh.health[i] >> 5) & 0x7 ) { case 0: strcpy(p, "OK;"); break; case 1: strcpy(p, "PARITY;"); break; case 2: strcpy(p, "TLM/HOW;"); break; case 3: strcpy(p, "Z-COUNT;"); break; case 4: strcpy(p, "SUBFRAME 1,2,3;"); break; case 5: strcpy(p, "SUBFRAME 4,5;"); break; case 6: strcpy(p, "UPLOAD BAD;"); break; case 7: strcpy(p, "DATA BAD;"); break; } p += strlen(p); switch (cfgh.health[i] & 0x1F) { case 0: strcpy(p, "SIGNAL OK"); break; case 0x1C: strcpy(p, "SV TEMP OUT"); break; case 0x1D: strcpy(p, "SV WILL BE TEMP OUT"); break; case 0x1E: break; case 0x1F: strcpy(p, "MULTIPLE ERRS"); break; default: strcpy(p, "TRANSMISSION PROBLEMS"); break; } strcat(p, "\""); set_var(&parse->kv, buffer, sizeof(buffer), RO); } } } break; case GPS_ALM: break; case GPS_EPH: break; case GPS_UTC: { UTC utc; char buffer[512]; char *p; p = buffer; get_mbg_utc(&bufp, &utc); if (utc.valid) { strcpy(p, "gps_utc_correction=\""); p += strlen(p); mk_utcinfo(p, utc.t0t.wn, utc.WNlsf, utc.DNt, utc.delta_tls, utc.delta_tlsf); strcat(p, "\""); } else { strcpy(p, "gps_utc_correction=\"\""); } set_var(&parse->kv, buffer, sizeof(buffer), RO|DEF); } break; case GPS_IONO: break; case GPS_ASCII_MSG: { ASCII_MSG gps_ascii_msg; char buffer[128]; get_mbg_ascii_msg(&bufp, &gps_ascii_msg); if (gps_ascii_msg.valid) { char buffer1[128]; mkreadable(buffer1, sizeof(buffer1), gps_ascii_msg.s, strlen(gps_ascii_msg.s), (int)0); sprintf(buffer, "gps_message=\"%s\"", buffer1); } else strcpy(buffer, "gps_message="); set_var(&parse->kv, buffer, 128, RO|DEF); } break; default: break; } } else { msyslog(LOG_DEBUG, "PARSE receiver #%d: gps16x_message: message checksum error: hdr_csum = 0x%x (expected 0x%lx), data_len = %d, data_csum = 0x%x (expected 0x%lx)", CLK_UNIT(parse->peer), header.gps_hdr_csum, mbg_csum(parsetime->parse_msg + 1, 6), header.gps_len, header.gps_data_csum, mbg_csum(bufp, (unsigned)((header.gps_len < sizeof(parsetime->parse_msg)) ? header.gps_len : 0))); } } return; } /*------------------------------------------------------------ * gps16x_poll - query the reciver peridically */ static void gps16x_poll( struct peer *peer ) { struct parseunit *parse = (struct parseunit *)peer->procptr->unitptr; static GPS_MSG_HDR sequence[] = { { GPS_SW_REV, 0, 0, 0 }, { GPS_STAT, 0, 0, 0 }, { GPS_UTC, 0, 0, 0 }, { GPS_ASCII_MSG, 0, 0, 0 }, { GPS_ANT_INFO, 0, 0, 0 }, { GPS_CFGH, 0, 0, 0 }, { GPS_POS_XYZ, 0, 0, 0 }, { GPS_POS_LLA, 0, 0, 0 }, { (unsigned short)~0, 0, 0, 0 } }; int rtc; unsigned char cmd_buffer[64]; unsigned char *outp = cmd_buffer; GPS_MSG_HDR *header; if (((poll_info_t *)parse->parse_type->cl_data)->rate) { parse->peer->nextaction = current_time + ((poll_info_t *)parse->parse_type->cl_data)->rate; } if (sequence[parse->localstate].gps_cmd == (unsigned short)~0) parse->localstate = 0; header = sequence + parse->localstate++; *outp++ = SOH; /* start command */ put_mbg_header(&outp, header); outp = cmd_buffer + 1; header->gps_hdr_csum = (short)mbg_csum(outp, 6); put_mbg_header(&outp, header); #ifdef DEBUG if (debug > 2) { char buffer[128]; mkreadable(buffer, sizeof(buffer), (char *)cmd_buffer, (unsigned)(outp - cmd_buffer), 1); printf("PARSE receiver #%d: transmitted message #%ld (%d bytes) >%s<\n", CLK_UNIT(parse->peer), parse->localstate - 1, (int)(outp - cmd_buffer), buffer); } #endif rtc = write(parse->generic->io.fd, cmd_buffer, (unsigned long)(outp - cmd_buffer)); if (rtc < 0) { ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: gps16x_poll: failed to send cmd to clock: %m", CLK_UNIT(parse->peer)); } else if (rtc != outp - cmd_buffer) { ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: gps16x_poll: failed to send cmd incomplete (%d of %d bytes sent)", CLK_UNIT(parse->peer), rtc, (int)(outp - cmd_buffer)); } clear_err(parse, ERR_BADIO); return; } /*-------------------------------------------------- * init routine - setup timer */ static int gps16x_poll_init( struct parseunit *parse ) { if (((poll_info_t *)parse->parse_type->cl_data)->rate) { parse->peer->action = gps16x_poll; gps16x_poll(parse->peer); } return 0; } #else static void gps16x_message( struct parseunit *parse, parsetime_t *parsetime ) {} static int gps16x_poll_init( struct parseunit *parse ) { return 1; } #endif /* CLOCK_MEINBERG */ /**=========================================================================== ** clock polling support **/ /*-------------------------------------------------- * direct poll routine */ static void poll_dpoll( struct parseunit *parse ) { int rtc; const char *ps = ((poll_info_t *)parse->parse_type->cl_data)->string; int ct = ((poll_info_t *)parse->parse_type->cl_data)->count; rtc = write(parse->generic->io.fd, ps, (unsigned long)ct); if (rtc < 0) { ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: poll_dpoll: failed to send cmd to clock: %m", CLK_UNIT(parse->peer)); } else if (rtc != ct) { ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: poll_dpoll: failed to send cmd incomplete (%d of %d bytes sent)", CLK_UNIT(parse->peer), rtc, ct); } clear_err(parse, ERR_BADIO); } /*-------------------------------------------------- * periodic poll routine */ static void poll_poll( struct peer *peer ) { struct parseunit *parse = (struct parseunit *)peer->procptr->unitptr; if (parse->parse_type->cl_poll) parse->parse_type->cl_poll(parse); if (((poll_info_t *)parse->parse_type->cl_data)->rate) { parse->peer->nextaction = current_time + ((poll_info_t *)parse->parse_type->cl_data)->rate; } } /*-------------------------------------------------- * init routine - setup timer */ static int poll_init( struct parseunit *parse ) { if (((poll_info_t *)parse->parse_type->cl_data)->rate) { parse->peer->action = poll_poll; poll_poll(parse->peer); } return 0; } /**=========================================================================== ** Trimble support **/ /*------------------------------------------------------------- * trimble TAIP init routine - setup EOL and then do poll_init. */ static int trimbletaip_init( struct parseunit *parse ) { #ifdef HAVE_TERMIOS struct termios tio; #endif #ifdef HAVE_SYSV_TTYS struct termio tio; #endif /* * configure terminal line for trimble receiver */ if (TTY_GETATTR(parse->generic->io.fd, &tio) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: trimbletaip_init: tcgetattr(fd, &tio): %m", CLK_UNIT(parse->peer)); return 0; } else { tio.c_cc[VEOL] = TRIMBLETAIP_EOL; if (TTY_SETATTR(parse->generic->io.fd, &tio) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: trimbletaip_init: tcsetattr(fd, &tio): %m", CLK_UNIT(parse->peer)); return 0; } } return poll_init(parse); } /*-------------------------------------------------- * trimble TAIP event routine - reset receiver upon data format trouble */ static const char *taipinit[] = { ">FPV00000000<", ">SRM;ID_FLAG=F;CS_FLAG=T;EC_FLAG=F;FR_FLAG=T;CR_FLAG=F<", ">FTM00020001<", (char *)0 }; static void trimbletaip_event( struct parseunit *parse, int event ) { switch (event) { case CEVNT_BADREPLY: /* reset on garbled input */ case CEVNT_TIMEOUT: /* reset on no input */ { const char **iv; iv = taipinit; while (*iv) { int rtc = write(parse->generic->io.fd, *iv, strlen(*iv)); if (rtc < 0) { msyslog(LOG_ERR, "PARSE receiver #%d: trimbletaip_event: failed to send cmd to clock: %m", CLK_UNIT(parse->peer)); return; } else { if (rtc != strlen(*iv)) { msyslog(LOG_ERR, "PARSE receiver #%d: trimbletaip_event: failed to send cmd incomplete (%d of %d bytes sent)", CLK_UNIT(parse->peer), rtc, (int)strlen(*iv)); return; } } iv++; } NLOG(NLOG_CLOCKINFO) ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: trimbletaip_event: RECEIVER INITIALIZED", CLK_UNIT(parse->peer)); } break; default: /* ignore */ break; } } /* * This driver supports the Trimble SVee Six Plus GPS receiver module. * It should support other Trimble receivers which use the Trimble Standard * Interface Protocol (see below). * * The module has a serial I/O port for command/data and a 1 pulse-per-second * output, about 1 microsecond wide. The leading edge of the pulse is * coincident with the change of the GPS second. This is the same as * the change of the UTC second +/- ~1 microsecond. Some other clocks * specifically use a feature in the data message as a timing reference, but * the SVee Six Plus does not do this. In fact there is considerable jitter * on the timing of the messages, so this driver only supports the use * of the PPS pulse for accurate timing. Where it is determined that * the offset is way off, when first starting up ntpd for example, * the timing of the data stream is used until the offset becomes low enough * (|offset| < CLOCK_MAX), at which point the pps offset is used. * * It can use either option for receiving PPS information - the 'ppsclock' * stream pushed onto the serial data interface to timestamp the Carrier * Detect interrupts, where the 1PPS connects to the CD line. This only * works on SunOS 4.1.x currently. To select this, define PPSPPS in * Config.local. The other option is to use a pulse-stretcher/level-converter * to convert the PPS pulse into a RS232 start pulse & feed this into another * tty port. To use this option, define PPSCLK in Config.local. The pps input, * by whichever method, is handled in ntp_loopfilter.c * * The receiver uses a serial message protocol called Trimble Standard * Interface Protocol (it can support others but this driver only supports * TSIP). Messages in this protocol have the following form: * * ... ... * * Any bytes within the portion of value 10 hex () are doubled * on transmission and compressed back to one on reception. Otherwise * the values of data bytes can be anything. The serial interface is RS-422 * asynchronous using 9600 baud, 8 data bits with odd party (**note** 9 bits * in total!), and 1 stop bit. The protocol supports byte, integer, single, * and double datatypes. Integers are two bytes, sent most significant first. * Singles are IEEE754 single precision floating point numbers (4 byte) sent * sign & exponent first. Doubles are IEEE754 double precision floating point * numbers (8 byte) sent sign & exponent first. * The receiver supports a large set of messages, only a small subset of * which are used here. From driver to receiver the following are used: * * ID Description * * 21 Request current time * 22 Mode Select * 2C Set/Request operating parameters * 2F Request UTC info * 35 Set/Request I/O options * From receiver to driver the following are recognised: * * ID Description * * 41 GPS Time * 44 Satellite selection, PDOP, mode * 46 Receiver health * 4B Machine code/status * 4C Report operating parameters (debug only) * 4F UTC correction data (used to get leap second warnings) * 55 I/O options (debug only) * * All others are accepted but ignored. * */ #define PI 3.1415926535898 /* lots of sig figs */ #define D2R PI/180.0 /*------------------------------------------------------------------- * sendcmd, sendbyte, sendetx, sendflt, sendint implement the command * interface to the receiver. * * CAVEAT: the sendflt, sendint routines are byte order dependend and * float implementation dependend - these must be converted to portable * versions ! * * CURRENT LIMITATION: float implementation. This runs only on systems * with IEEE754 floats as native floats */ typedef struct trimble { u_long last_msg; /* last message received */ u_char qtracking; /* query tracking status */ u_long ctrack; /* current tracking set */ u_long ltrack; /* last tracking set */ } trimble_t; union uval { u_char bd[8]; int iv; float fv; double dv; }; struct txbuf { short idx; /* index to first unused byte */ u_char *txt; /* pointer to actual data buffer */ }; void sendcmd P((struct txbuf *buf, int c)); void sendbyte P((struct txbuf *buf, int b)); void sendetx P((struct txbuf *buf, struct parseunit *parse)); void sendint P((struct txbuf *buf, int a)); void sendflt P((struct txbuf *buf, double a)); void sendcmd( struct txbuf *buf, int c ) { buf->txt[0] = DLE; buf->txt[1] = (u_char)c; buf->idx = 2; } void sendbyte( struct txbuf *buf, int b ) { if (b == DLE) buf->txt[buf->idx++] = DLE; buf->txt[buf->idx++] = (u_char)b; } void sendetx( struct txbuf *buf, struct parseunit *parse ) { buf->txt[buf->idx++] = DLE; buf->txt[buf->idx++] = ETX; if (write(parse->generic->io.fd, buf->txt, (unsigned long)buf->idx) != buf->idx) { ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: sendetx: failed to send cmd to clock: %m", CLK_UNIT(parse->peer)); } else { #ifdef DEBUG if (debug > 2) { char buffer[256]; mkreadable(buffer, sizeof(buffer), (char *)buf->txt, (unsigned)buf->idx, 1); printf("PARSE receiver #%d: transmitted message (%d bytes) >%s<\n", CLK_UNIT(parse->peer), buf->idx, buffer); } #endif clear_err(parse, ERR_BADIO); } } void sendint( struct txbuf *buf, int a ) { /* send 16bit int, msbyte first */ sendbyte(buf, (u_char)((a>>8) & 0xff)); sendbyte(buf, (u_char)(a & 0xff)); } void sendflt( struct txbuf *buf, double a ) { int i; union uval uval; uval.fv = a; #ifdef WORDS_BIGENDIAN for (i=0; i<=3; i++) #else for (i=3; i>=0; i--) #endif sendbyte(buf, uval.bd[i]); } #define TRIM_POS_OPT 0x13 /* output position with high precision */ #define TRIM_TIME_OPT 0x03 /* use UTC time stamps, on second */ /*-------------------------------------------------- * trimble TSIP setup routine */ static int trimbletsip_setup( struct parseunit *parse, const char *reason ) { u_char buffer[256]; struct txbuf buf; buf.txt = buffer; sendcmd(&buf, CMD_CVERSION); /* request software versions */ sendetx(&buf, parse); sendcmd(&buf, CMD_COPERPARAM); /* set operating parameters */ sendbyte(&buf, 4); /* static */ sendflt(&buf, 5.0*D2R); /* elevation angle mask = 10 deg XXX */ sendflt(&buf, 4.0); /* s/n ratio mask = 6 XXX */ sendflt(&buf, 12.0); /* PDOP mask = 12 */ sendflt(&buf, 8.0); /* PDOP switch level = 8 */ sendetx(&buf, parse); sendcmd(&buf, CMD_CMODESEL); /* fix mode select */ sendbyte(&buf, 0); /* automatic */ sendetx(&buf, parse); sendcmd(&buf, CMD_CMESSAGE); /* request system message */ sendetx(&buf, parse); sendcmd(&buf, CMD_CSUPER); /* superpacket fix */ sendbyte(&buf, 0x2); /* binary mode */ sendetx(&buf, parse); sendcmd(&buf, CMD_CIOOPTIONS); /* set I/O options */ sendbyte(&buf, TRIM_POS_OPT); /* position output */ sendbyte(&buf, 0x00); /* no velocity output */ sendbyte(&buf, TRIM_TIME_OPT); /* UTC, compute on seconds */ sendbyte(&buf, 0x00); /* no raw measurements */ sendetx(&buf, parse); sendcmd(&buf, CMD_CUTCPARAM); /* request UTC correction data */ sendetx(&buf, parse); NLOG(NLOG_CLOCKINFO) ERR(ERR_BADIO) msyslog(LOG_ERR, "PARSE receiver #%d: trimbletsip_setup: RECEIVER RE-INITIALIZED (%s)", CLK_UNIT(parse->peer), reason); return 0; } /*-------------------------------------------------- * TRIMBLE TSIP check routine */ static void trimble_check( struct peer *peer ) { struct parseunit *parse = (struct parseunit *)peer->procptr->unitptr; trimble_t *t = parse->localdata; u_char buffer[256]; struct txbuf buf; buf.txt = buffer; if (t) { if (current_time > t->last_msg + TRIMBLETSIP_IDLE_TIME) (void)trimbletsip_setup(parse, "message timeout"); } poll_poll(parse->peer); /* emit query string and re-arm timer */ if (t->qtracking) { u_long oldsats = t->ltrack & ~t->ctrack; t->qtracking = 0; t->ltrack = t->ctrack; if (oldsats) { int i; for (i = 0; oldsats; i++) if (oldsats & (1 << i)) { sendcmd(&buf, CMD_CSTATTRACK); sendbyte(&buf, i+1); /* old sat */ sendetx(&buf, parse); } oldsats &= ~(1 << i); } sendcmd(&buf, CMD_CSTATTRACK); sendbyte(&buf, 0x00); /* current tracking set */ sendetx(&buf, parse); } } /*-------------------------------------------------- * TRIMBLE TSIP end routine */ static void trimbletsip_end( struct parseunit *parse ) { trimble_t *t = parse->localdata; if (t) { free(t); parse->localdata = (void *)0; } parse->peer->nextaction = 0; parse->peer->action = (void (*) P((struct peer *)))0; } /*-------------------------------------------------- * TRIMBLE TSIP init routine */ static int trimbletsip_init( struct parseunit *parse ) { #if defined(VEOL) || defined(VEOL2) #ifdef HAVE_TERMIOS struct termios tio; /* NEEDED FOR A LONG TIME ! */ #endif #ifdef HAVE_SYSV_TTYS struct termio tio; /* NEEDED FOR A LONG TIME ! */ #endif /* * allocate local data area */ if (!parse->localdata) { trimble_t *t; t = (trimble_t *)(parse->localdata = emalloc(sizeof(trimble_t))); if (t) { memset((char *)t, 0, sizeof(trimble_t)); t->last_msg = current_time; } } parse->peer->action = trimble_check; parse->peer->nextaction = current_time; /* * configure terminal line for ICANON mode with VEOL characters */ if (TTY_GETATTR(parse->generic->io.fd, &tio) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: trimbletsip_init: tcgetattr(%d, &tio): %m", CLK_UNIT(parse->peer), parse->generic->io.fd); return 0; } else { if ((parse_clockinfo[CLK_TYPE(parse->peer)].cl_lflag & ICANON)) { #ifdef VEOL tio.c_cc[VEOL] = ETX; #endif #ifdef VEOL2 tio.c_cc[VEOL2] = DLE; #endif } if (TTY_SETATTR(parse->generic->io.fd, &tio) == -1) { msyslog(LOG_ERR, "PARSE receiver #%d: trimbletsip_init: tcsetattr(%d, &tio): %m", CLK_UNIT(parse->peer), parse->generic->io.fd); return 0; } } #endif return trimbletsip_setup(parse, "initial startup"); } /*------------------------------------------------------------ * trimbletsip_event - handle Trimble events * simple evente handler - attempt to re-initialize receiver */ static void trimbletsip_event( struct parseunit *parse, int event ) { switch (event) { case CEVNT_BADREPLY: /* reset on garbled input */ case CEVNT_TIMEOUT: /* reset on no input */ (void)trimbletsip_setup(parse, "event BAD_REPLY/TIMEOUT"); break; default: /* ignore */ break; } } /* * getflt, getint convert fields in the incoming data into the * appropriate type of item * * CAVEAT: these routines are currently definitely byte order dependent * and assume Representation(float) == IEEE754 * These functions MUST be converted to portable versions (especially * converting the float representation into ntp_fp formats in order * to avoid floating point operations at all! */ static float getflt( u_char *bp ) { union uval uval; #ifdef WORDS_BIGENDIAN uval.bd[0] = *bp++; uval.bd[1] = *bp++; uval.bd[2] = *bp++; uval.bd[3] = *bp; #else /* ! WORDS_BIGENDIAN */ uval.bd[3] = *bp++; uval.bd[2] = *bp++; uval.bd[1] = *bp++; uval.bd[0] = *bp; #endif /* ! WORDS_BIGENDIAN */ return uval.fv; } static double getdbl( u_char *bp ) { union uval uval; #ifdef WORDS_BIGENDIAN uval.bd[0] = *bp++; uval.bd[1] = *bp++; uval.bd[2] = *bp++; uval.bd[3] = *bp++; uval.bd[4] = *bp++; uval.bd[5] = *bp++; uval.bd[6] = *bp++; uval.bd[7] = *bp; #else /* ! WORDS_BIGENDIAN */ uval.bd[7] = *bp++; uval.bd[6] = *bp++; uval.bd[5] = *bp++; uval.bd[4] = *bp++; uval.bd[3] = *bp++; uval.bd[2] = *bp++; uval.bd[1] = *bp++; uval.bd[0] = *bp; #endif /* ! WORDS_BIGENDIAN */ return uval.dv; } static int getshort( unsigned char *p ) { return get_msb_short(&p); } /*-------------------------------------------------- * trimbletsip_message - process trimble messages */ #define RTOD (180.0 / 3.1415926535898) #define mb(_X_) (buffer[2+(_X_)]) /* shortcut for buffer access */ static void trimbletsip_message( struct parseunit *parse, parsetime_t *parsetime ) { unsigned char *buffer = parsetime->parse_msg; unsigned int size = parsetime->parse_msglen; if ((size < 4) || (buffer[0] != DLE) || (buffer[size-1] != ETX) || (buffer[size-2] != DLE)) { #ifdef DEBUG if (debug > 2) { int i; printf("TRIMBLE BAD packet, size %d:\n ", size); for (i = 0; i < size; i++) { printf ("%2.2x, ", buffer[i]&0xff); if (i%16 == 15) printf("\n\t"); } printf("\n"); } #endif return; } else { int var_flag; trimble_t *tr = parse->localdata; unsigned int cmd = buffer[1]; char pbuffer[200]; char *t = pbuffer; cmd_info_t *s; #ifdef DEBUG if (debug > 3) { int i; printf("TRIMBLE packet 0x%02x, size %d:\n ", cmd, size); for (i = 0; i < size; i++) { printf ("%2.2x, ", buffer[i]&0xff); if (i%16 == 15) printf("\n\t"); } printf("\n"); } #endif if (tr) tr->last_msg = current_time; s = trimble_convert(cmd, trimble_rcmds); if (s) { sprintf(t, "%s=\"", s->varname); } else { printf("TRIMBLE unknown command 0x%02x\n", cmd); return; } var_flag = s->varmode; t += strlen(t); switch(cmd) { case CMD_RCURTIME: sprintf(t, "%f, %d, %f", getflt((unsigned char *)&mb(0)), getshort((unsigned char *)&mb(4)), getflt((unsigned char *)&mb(6))); break; case CMD_RBEST4: strcpy(t, "mode: "); t += strlen(t); switch (mb(0) & 0xF) { default: sprintf(t, "0x%x", mb(0) & 0x7); break; case 1: strcat(t, "0D"); break; case 3: strcat(t, "2D"); break; case 4: strcat(t, "3D"); break; } t += strlen(t); if (mb(0) & 0x10) strcpy(t, "-MANUAL, "); else strcpy(t, "-AUTO, "); t += strlen(t); sprintf(t, "satellites %02d %02d %02d %02d, PDOP %.2f, HDOP %.2f, VDOP %.2f, TDOP %.2f", mb(1), mb(2), mb(3), mb(4), getflt((unsigned char *)&mb(5)), getflt((unsigned char *)&mb(9)), getflt((unsigned char *)&mb(13)), getflt((unsigned char *)&mb(17))); break; case CMD_RVERSION: sprintf(t, "%d.%d (%d/%d/%d)", mb(0)&0xff, mb(1)&0xff, 1900+(mb(4)&0xff), mb(2)&0xff, mb(3)&0xff); break; case CMD_RRECVHEALTH: { static const char *msgs[] = { "Battery backup failed", "Signal processor error", "Alignment error, channel or chip 1", "Alignment error, channel or chip 2", "Antenna feed line fault", "Excessive ref freq. error", "", "" }; int i, bits; switch (mb(0) & 0xFF) { default: sprintf(t, "illegal value 0x%02x", mb(0) & 0xFF); break; case 0x00: strcpy(t, "doing position fixes"); break; case 0x01: strcpy(t, "no GPS time yet"); break; case 0x03: strcpy(t, "PDOP too high"); break; case 0x08: strcpy(t, "no usable satellites"); break; case 0x09: strcpy(t, "only ONE usable satellite"); break; case 0x0A: strcpy(t, "only TWO usable satellites"); break; case 0x0B: strcpy(t, "only THREE usable satellites"); break; case 0x0C: strcpy(t, "the chosen satellite is unusable"); break; } t += strlen(t); bits = mb(1) & 0xFF; for (i = 0; i < 8; i++) if (bits & (0x1<", "", "" }; int i, bits; sprintf(t, "machine id 0x%02x", mb(0) & 0xFF); t += strlen(t); bits = mb(1) & 0xFF; for (i = 0; i < 8; i++) if (bits & (0x1<"); } } break; case CMD_RSAT1BIAS: sprintf(t, "%.1fm %.2fm/s at %.1fs", getflt(&mb(0)), getflt(&mb(4)), getflt(&mb(8))); break; case CMD_RIOOPTIONS: { sprintf(t, "%02x %02x %02x %02x", mb(0), mb(1), mb(2), mb(3)); if (mb(0) != TRIM_POS_OPT || mb(2) != TRIM_TIME_OPT) { (void)trimbletsip_setup(parse, "bad io options"); } } break; case CMD_RSPOSXYZ: { double x = getflt((unsigned char *)&mb(0)); double y = getflt((unsigned char *)&mb(4)); double z = getflt((unsigned char *)&mb(8)); double f = getflt((unsigned char *)&mb(12)); if (f > 0.0) sprintf(t, "x= %.1fm, y= %.1fm, z= %.1fm, time_of_fix= %f sec", x, y, z, f); else return; } break; case CMD_RSLLAPOS: { double lat = getflt((unsigned char *)&mb(0)); double lng = getflt((unsigned char *)&mb(4)); double f = getflt((unsigned char *)&mb(12)); if (f > 0.0) sprintf(t, "lat %f %c, long %f %c, alt %.2fm", ((lat < 0.0) ? (-lat) : (lat))*RTOD, (lat < 0.0 ? 'S' : 'N'), ((lng < 0.0) ? (-lng) : (lng))*RTOD, (lng < 0.0 ? 'W' : 'E'), getflt((unsigned char *)&mb(8))); else return; } break; case CMD_RDOUBLEXYZ: { double x = getdbl((unsigned char *)&mb(0)); double y = getdbl((unsigned char *)&mb(8)); double z = getdbl((unsigned char *)&mb(16)); sprintf(t, "x= %.1fm, y= %.1fm, z= %.1fm", x, y, z); } break; case CMD_RDOUBLELLA: { double lat = getdbl((unsigned char *)&mb(0)); double lng = getdbl((unsigned char *)&mb(8)); sprintf(t, "lat %f %c, lon %f %c, alt %.2fm", ((lat < 0.0) ? (-lat) : (lat))*RTOD, (lat < 0.0 ? 'S' : 'N'), ((lng < 0.0) ? (-lng) : (lng))*RTOD, (lng < 0.0 ? 'W' : 'E'), getdbl((unsigned char *)&mb(16))); } break; case CMD_RALLINVIEW: { int i, sats; strcpy(t, "mode: "); t += strlen(t); switch (mb(0) & 0x7) { default: sprintf(t, "0x%x", mb(0) & 0x7); break; case 3: strcat(t, "2D"); break; case 4: strcat(t, "3D"); break; } t += strlen(t); if (mb(0) & 0x8) strcpy(t, "-MANUAL, "); else strcpy(t, "-AUTO, "); t += strlen(t); sats = (mb(0)>>4) & 0xF; sprintf(t, "PDOP %.2f, HDOP %.2f, VDOP %.2f, TDOP %.2f, %d satellite%s in view: ", getflt((unsigned char *)&mb(1)), getflt((unsigned char *)&mb(5)), getflt((unsigned char *)&mb(9)), getflt((unsigned char *)&mb(13)), sats, (sats == 1) ? "" : "s"); t += strlen(t); for (i=0; i < sats; i++) { sprintf(t, "%s%02d", i ? ", " : "", mb(17+i)); t += strlen(t); if (tr) tr->ctrack |= (1 << (mb(17+i)-1)); } if (tr) { /* mark for tracking status query */ tr->qtracking = 1; } } break; case CMD_RSTATTRACK: { sprintf(t-2, "[%02d]=\"", mb(0)); /* add index to var name */ t += strlen(t); if (getflt((unsigned char *)&mb(4)) < 0.0) { strcpy(t, ""); var_flag &= ~DEF; } else { sprintf(t, "ch=%d, acq=%s, eph=%d, signal_level= %5.2f, elevation= %5.2f, azimuth= %6.2f", (mb(1) & 0xFF)>>3, mb(2) ? ((mb(2) == 1) ? "ACQ" : "SRCH") : "NEVER", mb(3), getflt((unsigned char *)&mb(4)), getflt((unsigned char *)&mb(12)) * RTOD, getflt((unsigned char *)&mb(16)) * RTOD); t += strlen(t); if (mb(20)) { var_flag &= ~DEF; strcpy(t, ", OLD"); } t += strlen(t); if (mb(22)) { if (mb(22) == 1) strcpy(t, ", BAD PARITY"); else if (mb(22) == 2) strcpy(t, ", BAD EPH HEALTH"); } t += strlen(t); if (mb(23)) strcpy(t, ", collecting data"); } } break; default: strcpy(t, ""); break; } strcat(t,"\""); set_var(&parse->kv, pbuffer, sizeof(pbuffer), var_flag); } } /**============================================================ ** RAWDCF support **/ /*-------------------------------------------------- * rawdcf_init_1 - set up modem lines for RAWDCF receivers * SET DTR line */ #if defined(TIOCMSET) && (defined(TIOCM_DTR) || defined(CIOCM_DTR)) static int rawdcf_init_1( struct parseunit *parse ) { /* fixed 2000 for using with Linux by Wolfram Pienkoss */ /* * You can use the RS232 to supply the power for a DCF77 receiver. * Here a voltage between the DTR and the RTS line is used. Unfortunately * the name has changed from CIOCM_DTR to TIOCM_DTR recently. */ int sl232; if (ioctl(parse->generic->io.fd, TIOCMGET, (caddr_t)&sl232) == -1) { msyslog(LOG_NOTICE, "PARSE receiver #%d: rawdcf_init_1: WARNING: ioctl(fd, TIOCMGET, [C|T]IOCM_DTR): %m", CLK_UNIT(parse->peer)); return 0; } #ifdef TIOCM_DTR sl232 = (sl232 & ~TIOCM_RTS) | TIOCM_DTR; /* turn on DTR, clear RTS for power supply */ #else sl232 = (sl232 & ~CIOCM_RTS) | CIOCM_DTR; /* turn on DTR, clear RTS for power supply */ #endif if (ioctl(parse->generic->io.fd, TIOCMSET, (caddr_t)&sl232) == -1) { msyslog(LOG_NOTICE, "PARSE receiver #%d: rawdcf_init_1: WARNING: ioctl(fd, TIOCMSET, [C|T]IOCM_DTR): %m", CLK_UNIT(parse->peer)); } return 0; } #else static int rawdcfdtr_init_1( struct parseunit *parse ) { msyslog(LOG_NOTICE, "PARSE receiver #%d: rawdcf_init_1: WARNING: OS interface incapable of setting DTR to power DCF modules", CLK_UNIT(parse->peer)); return 0; } #endif /* DTR initialisation type */ /*-------------------------------------------------- * rawdcf_init_2 - set up modem lines for RAWDCF receivers * CLR DTR line, SET RTS line */ #if defined(TIOCMSET) && (defined(TIOCM_RTS) || defined(CIOCM_RTS)) static int rawdcf_init_2( struct parseunit *parse ) { /* fixed 2000 for using with Linux by Wolfram Pienkoss */ /* * You can use the RS232 to supply the power for a DCF77 receiver. * Here a voltage between the DTR and the RTS line is used. Unfortunately * the name has changed from CIOCM_DTR to TIOCM_DTR recently. */ int sl232; if (ioctl(parse->generic->io.fd, TIOCMGET, (caddr_t)&sl232) == -1) { msyslog(LOG_NOTICE, "PARSE receiver #%d: rawdcf_init_2: WARNING: ioctl(fd, TIOCMGET, [C|T]IOCM_RTS): %m", CLK_UNIT(parse->peer)); return 0; } #ifdef TIOCM_RTS sl232 = (sl232 & ~TIOCM_DTR) | TIOCM_RTS; /* turn on RTS, clear DTR for power supply */ #else sl232 = (sl232 & ~CIOCM_DTR) | CIOCM_RTS; /* turn on RTS, clear DTR for power supply */ #endif if (ioctl(parse->generic->io.fd, TIOCMSET, (caddr_t)&sl232) == -1) { msyslog(LOG_NOTICE, "PARSE receiver #%d: rawdcf_init_2: WARNING: ioctl(fd, TIOCMSET, [C|T]IOCM_RTS): %m", CLK_UNIT(parse->peer)); } return 0; } #else static int rawdcf_init_2( struct parseunit *parse ) { msyslog(LOG_NOTICE, "PARSE receiver #%d: rawdcf_init_2: WARNING: OS interface incapable of setting RTS to power DCF modules", CLK_UNIT(parse->peer)); return 0; } #endif /* DTR initialisation type */ #else /* defined(REFCLOCK) && defined(PARSE) */ int refclock_parse_bs; #endif /* defined(REFCLOCK) && defined(PARSE) */ /* * History: * * refclock_parse.c,v * Revision 4.36 1999/11/28 17:18:20 kardel * disabled burst mode * * Revision 4.35 1999/11/28 09:14:14 kardel * RECON_4_0_98F * * Revision 4.34 1999/05/14 06:08:05 kardel * store current_time in a suitable container (u_long) * * Revision 4.33 1999/05/13 21:48:38 kardel * double the no response timeout interval * * Revision 4.32 1999/05/13 20:09:13 kardel * complain only about missing polls after a full poll interval * * Revision 4.31 1999/05/13 19:59:32 kardel * add clock type 16 for RTS set DTR clr in RAWDCF * * Revision 4.30 1999/02/28 20:36:43 kardel * fixed printf fmt * * Revision 4.29 1999/02/28 19:58:23 kardel * updated copyright information * * Revision 4.28 1999/02/28 19:01:50 kardel * improved debug out on sent Meinberg messages * * Revision 4.27 1999/02/28 18:05:55 kardel * no linux/ppsclock.h stuff * * Revision 4.26 1999/02/28 15:27:27 kardel * wharton clock integration * * Revision 4.25 1999/02/28 14:04:46 kardel * added missing double quotes to UTC information string * * Revision 4.24 1999/02/28 12:06:50 kardel * (parse_control): using gmprettydate instead of prettydate() * (mk_utcinfo): new function for formatting GPS derived UTC information * (gps16x_message): changed to use mk_utcinfo() * (trimbletsip_message): changed to use mk_utcinfo() * ignoring position information in unsynchronized mode * (parse_start): augument linux support for optional ASYNC_LOW_LATENCY * * Revision 4.23 1999/02/23 19:47:53 kardel * fixed #endifs * (stream_receive): fixed formats * * Revision 4.22 1999/02/22 06:21:02 kardel * use new autoconfig symbols * * Revision 4.21 1999/02/21 12:18:13 kardel * 4.91f reconcilation * * Revision 4.20 1999/02/21 10:53:36 kardel * initial Linux PPSkit version * * Revision 4.19 1999/02/07 09:10:45 kardel * clarify STREAMS mitigation rules in comment * * Revision 4.18 1998/12/20 23:45:34 kardel * fix types and warnings * * Revision 4.17 1998/11/15 21:24:51 kardel * cannot access mbg_ routines when CLOCK_MEINBERG * is not defined * * Revision 4.16 1998/11/15 20:28:17 kardel * Release 4.0.73e13 reconcilation * * Revision 4.15 1998/08/22 21:56:08 kardel * fixed IO handling for non-STREAM IO * * Revision 4.14 1998/08/16 19:00:48 kardel * (gps16x_message): reduced UTC parameter information (dropped A0,A1) * made uval a local variable (killed one of the last globals) * (sendetx): added logging of messages when in debug mode * (trimble_check): added periodic checks to facilitate re-initialization * (trimbletsip_init): made use of EOL character if in non-kernel operation * (trimbletsip_message): extended message interpretation * (getdbl): fixed data conversion * * Revision 4.13 1998/08/09 22:29:13 kardel * Trimble TSIP support * * Revision 4.12 1998/07/11 10:05:34 kardel * Release 4.0.73d reconcilation * * Revision 4.11 1998/06/14 21:09:42 kardel * Sun acc cleanup * * Revision 4.10 1998/06/13 12:36:45 kardel * signed/unsigned, name clashes * * Revision 4.9 1998/06/12 15:30:00 kardel * prototype fixes * * Revision 4.8 1998/06/12 11:19:42 kardel * added direct input processing routine for refclocks in * order to avaiod that single character io gobbles up all * receive buffers and drops input data. (Problem started * with fast machines so a character a buffer was possible * one of the few cases where faster machines break existing * allocation algorithms) * * Revision 4.7 1998/06/06 18:35:20 kardel * (parse_start): added BURST mode initialisation * * Revision 4.6 1998/05/27 06:12:46 kardel * RAWDCF_BASEDELAY default added * old comment removed * casts for ioctl() * * Revision 4.5 1998/05/25 22:05:09 kardel * RAWDCF_SETDTR option removed * clock type 14 attempts to set DTR for * power supply of RAWDCF receivers * * Revision 4.4 1998/05/24 16:20:47 kardel * updated comments referencing Meinberg clocks * added RAWDCF clock with DTR set option as type 14 * * Revision 4.3 1998/05/24 10:48:33 kardel * calibrated CONRAD RAWDCF default fudge factor * * Revision 4.2 1998/05/24 09:59:35 kardel * corrected version information (ntpq support) * * Revision 4.1 1998/05/24 09:52:31 kardel * use fixed format only (new IO model) * output debug to stdout instead of msyslog() * don't include >"< in ASCII output in order not to confuse * ntpq parsing * * Revision 4.0 1998/04/10 19:52:11 kardel * Start 4.0 release version numbering * * Revision 1.2 1998/04/10 19:28:04 kardel * initial NTP VERSION 4 integration of PARSE with GPS166 binary support * derived from 3.105.1.2 from V3 tree * * Revision information 3.1 - 3.105 from log deleted 1998/04/10 kardel * */