/* $NetBSD: if_aue.c,v 1.13 2000/01/18 19:46:55 augustss Exp $ */ /* * Copyright (c) 1997, 1998, 1999, 2000 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD: src/sys/dev/usb/if_aue.c,v 1.11 2000/01/14 01:36:14 wpaul Exp $ */ /* * ADMtek AN986 Pegasus USB to ethernet driver. Datasheet is available * from http://www.admtek.com.tw. * * Written by Bill Paul * Electrical Engineering Department * Columbia University, New York City */ /* * The Pegasus chip uses four USB "endpoints" to provide 10/100 ethernet * support: the control endpoint for reading/writing registers, burst * read endpoint for packet reception, burst write for packet transmission * and one for "interrupts." The chip uses the same RX filter scheme * as the other ADMtek ethernet parts: one perfect filter entry for the * the station address and a 64-bit multicast hash table. The chip supports * both MII and HomePNA attachments. * * Since the maximum data transfer speed of USB is supposed to be 12Mbps, * you're never really going to get 100Mbps speeds from this device. I * think the idea is to allow the device to connect to 10 or 100Mbps * networks, not necessarily to provide 100Mbps performance. Also, since * the controller uses an external PHY chip, it's possible that board * designers might simply choose a 10Mbps PHY. * * Registers are accessed using usbd_do_request(). Packet transfers are * done using usbd_transfer() and friends. */ /* * Ported to NetBSD and somewhat rewritten by Lennart Augustsson. */ /* * TODO: * better error messages from rxstat * split out if_auevar.h * add thread to avoid register reads from interrupt context * more error checks * investigate short rx problem * proper cleanup on errors */ #if defined(__NetBSD__) || defined(__OpenBSD__) #include "opt_inet.h" #include "opt_ns.h" #include "bpfilter.h" #include "rnd.h" #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ #include #include #include #include #include #include #include #if defined(__FreeBSD__) #include #include /* for DELAY */ #include /* "controller miibus0" required. See GENERIC if you get errors here. */ #include "miibus_if.h" #elif defined(__NetBSD__) || defined(__OpenBSD__) #include #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ #include #include #include #include #if defined(__NetBSD__) || defined(__OpenBSD__) #include #define bpf_mtap(ifp, m) bpf_tap((ifp)->if_bpf, mtod((m), caddr_t), (m)->m_len) #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ #if defined(__FreeBSD__) || NBPFILTER > 0 #include #endif #if defined(__NetBSD__) || defined(__OpenBSD__) #ifdef INET #include #include #endif #ifdef NS #include #include #endif #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ #include #include #include #include #include #include #ifdef __FreeBSD__ #include #endif #include #ifdef AUE_DEBUG #define DPRINTF(x) if (auedebug) logprintf x #define DPRINTFN(n,x) if (auedebug >= (n)) logprintf x int auedebug = 0; #else #define DPRINTF(x) #define DPRINTFN(n,x) #endif /* * Various supported device vendors/products. */ static struct aue_type aue_devs[] = { { USB_VENDOR_BILLIONTON, USB_PRODUCT_BILLIONTON_USB100 }, { USB_VENDOR_MELCO, USB_PRODUCT_MELCO_LUATX }, { USB_VENDOR_LINKSYS, USB_PRODUCT_LINKSYS_USB100TX }, { USB_VENDOR_ADMTEK, USB_PRODUCT_ADMTEK_PEGASUS }, { USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX }, { USB_VENDOR_DLINK, USB_PRODUCT_DLINK_DSB650TX_PNA }, { USB_VENDOR_SMC, USB_PRODUCT_SMC_2202USB }, { 0, 0 } }; USB_DECLARE_DRIVER(aue); static int aue_tx_list_init __P((struct aue_softc *)); static int aue_rx_list_init __P((struct aue_softc *)); static int aue_newbuf __P((struct aue_softc *, struct aue_chain *, struct mbuf *)); static int aue_send __P((struct aue_softc *, struct mbuf *, int)); static void aue_intr __P((usbd_xfer_handle, usbd_private_handle, usbd_status)); static void aue_rxeof __P((usbd_xfer_handle, usbd_private_handle, usbd_status)); static void aue_txeof __P((usbd_xfer_handle, usbd_private_handle, usbd_status)); static void aue_tick __P((void *)); static void aue_start __P((struct ifnet *)); static int aue_ioctl __P((struct ifnet *, u_long, caddr_t)); static void aue_init __P((void *)); static void aue_stop __P((struct aue_softc *)); static void aue_watchdog __P((struct ifnet *)); #ifdef __FreeBSD__ static void aue_shutdown __P((device_ptr_t)); #endif static int aue_ifmedia_upd __P((struct ifnet *)); static void aue_ifmedia_sts __P((struct ifnet *, struct ifmediareq *)); static int aue_eeprom_getword __P((struct aue_softc *, int)); static void aue_read_mac __P((struct aue_softc *, u_char *)); static int aue_miibus_readreg __P((device_ptr_t, int, int)); #if defined(__FreeBSD__) static int aue_miibus_writereg __P((device_ptr_t, int, int, int)); #elif defined(__NetBSD__) || defined(__OpenBSD__) static void aue_miibus_writereg __P((device_ptr_t, int, int, int)); #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ static void aue_miibus_statchg __P((device_ptr_t)); static void aue_setmulti __P((struct aue_softc *)); static u_int32_t aue_crc __P((caddr_t)); static void aue_reset __P((struct aue_softc *)); static int csr_read_1 __P((struct aue_softc *, int)); static int csr_write_1 __P((struct aue_softc *, int, int)); static int csr_read_2 __P((struct aue_softc *, int)); static int csr_write_2 __P((struct aue_softc *, int, int)); #if defined(__FreeBSD__) #if !defined(lint) static const char rcsid[] = "$FreeBSD: src/sys/dev/usb/if_aue.c,v 1.11 2000/01/14 01:36:14 wpaul Exp $"; #endif static void aue_rxstart __P((struct ifnet *)); static struct usb_qdat aue_qdat; static device_method_t aue_methods[] = { /* Device interface */ DEVMETHOD(device_probe, aue_match), DEVMETHOD(device_attach, aue_attach), DEVMETHOD(device_detach, aue_detach), DEVMETHOD(device_shutdown, aue_shutdown), /* bus interface */ DEVMETHOD(bus_print_child, bus_generic_print_child), DEVMETHOD(bus_driver_added, bus_generic_driver_added), /* MII interface */ DEVMETHOD(miibus_readreg, aue_miibus_readreg), DEVMETHOD(miibus_writereg, aue_miibus_writereg), DEVMETHOD(miibus_statchg, aue_miibus_statchg), { 0, 0 } }; static driver_t aue_driver = { "aue", aue_methods, sizeof(struct aue_softc) }; static devclass_t aue_devclass; DRIVER_MODULE(if_aue, uhub, aue_driver, aue_devclass, usbd_driver_load, 0); DRIVER_MODULE(miibus, aue, miibus_driver, miibus_devclass, 0, 0); #endif /* __FreeBSD__ */ #define AUE_DO_REQUEST(dev, req, data) usbd_do_request_flags(dev, req, data, USBD_NO_TSLEEP, NULL) #define AUE_SETBIT(sc, reg, x) \ csr_write_1(sc, reg, csr_read_1(sc, reg) | (x)) #define AUE_CLRBIT(sc, reg, x) \ csr_write_1(sc, reg, csr_read_1(sc, reg) & ~(x)) static int csr_read_1(sc, reg) struct aue_softc *sc; int reg; { usb_device_request_t req; usbd_status err; uByte val = 0; int s; req.bmRequestType = UT_READ_VENDOR_DEVICE; req.bRequest = AUE_UR_READREG; USETW(req.wValue, 0); USETW(req.wIndex, reg); USETW(req.wLength, 1); s = splusb(); err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); splx(s); if (err) return (0); return (val); } static int csr_read_2(sc, reg) struct aue_softc *sc; int reg; { usb_device_request_t req; usbd_status err; uWord val; int s; req.bmRequestType = UT_READ_VENDOR_DEVICE; req.bRequest = AUE_UR_READREG; USETW(req.wValue, 0); USETW(req.wIndex, reg); USETW(req.wLength, 2); s = splusb(); err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); splx(s); if (err) return (0); return (UGETW(val)); } static int csr_write_1(sc, reg, aval) struct aue_softc *sc; int reg, aval; { usb_device_request_t req; usbd_status err; int s; uByte val; val = aval; req.bmRequestType = UT_WRITE_VENDOR_DEVICE; req.bRequest = AUE_UR_WRITEREG; USETW(req.wValue, val); USETW(req.wIndex, reg); USETW(req.wLength, 1); s = splusb(); err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); splx(s); if (err) return (-1); return (0); } static int csr_write_2(sc, reg, aval) struct aue_softc *sc; int reg, aval; { usb_device_request_t req; usbd_status err; int s; uWord val; USETW(val, aval); req.bmRequestType = UT_WRITE_VENDOR_DEVICE; req.bRequest = AUE_UR_WRITEREG; USETW(req.wValue, aval); USETW(req.wIndex, reg); USETW(req.wLength, 2); s = splusb(); err = AUE_DO_REQUEST(sc->aue_udev, &req, &val); splx(s); if (err) return (-1); return (0); } /* * Read a word of data stored in the EEPROM at address 'addr.' */ static int aue_eeprom_getword(sc, addr) struct aue_softc *sc; int addr; { int i; csr_write_1(sc, AUE_EE_REG, addr); csr_write_1(sc, AUE_EE_CTL, AUE_EECTL_READ); for (i = 0; i < AUE_TIMEOUT; i++) { if (csr_read_1(sc, AUE_EE_CTL) & AUE_EECTL_DONE) break; } if (i == AUE_TIMEOUT) { printf("%s: EEPROM read timed out\n", USBDEVNAME(sc->aue_dev)); } return (csr_read_2(sc, AUE_EE_DATA)); } /* * Read the MAC from the EEPROM. It's at offset 0. */ static void aue_read_mac(sc, dest) struct aue_softc *sc; u_char *dest; { int i; int off = 0; int word; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); for (i = 0; i < 3; i++) { word = aue_eeprom_getword(sc, off + i); dest[2 * i] = (u_char)word; dest[2 * i + 1] = (u_char)(word >> 8); } } static int aue_miibus_readreg(dev, phy, reg) device_ptr_t dev; int phy, reg; { struct aue_softc *sc = USBGETSOFTC(dev); int i; u_int16_t val; /* * The Am79C901 HomePNA PHY actually contains * two transceivers: a 1Mbps HomePNA PHY and a * 10Mbps full/half duplex ethernet PHY with * NWAY autoneg. However in the ADMtek adapter, * only the 1Mbps PHY is actually connected to * anything, so we ignore the 10Mbps one. It * happens to be configured for MII address 3, * so we filter that out. */ if (sc->aue_vendor == USB_VENDOR_ADMTEK && sc->aue_product == USB_PRODUCT_ADMTEK_PEGASUS) { if (phy != 1) return (0); } csr_write_1(sc, AUE_PHY_ADDR, phy); csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_READ); for (i = 0; i < AUE_TIMEOUT; i++) { if (csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) break; } if (i == AUE_TIMEOUT) { printf("%s: MII read timed out\n", USBDEVNAME(sc->aue_dev)); } val = csr_read_2(sc, AUE_PHY_DATA); DPRINTFN(11,("%s: %s: phy=%d reg=%d => 0x%04x\n", USBDEVNAME(sc->aue_dev), __FUNCTION__, phy, reg, val)); return (val); } #if defined(__FreeBSD__) static int #elif defined(__NetBSD__) || defined(__OpenBSD__) static void #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ aue_miibus_writereg(dev, phy, reg, data) device_ptr_t dev; int phy, reg, data; { struct aue_softc *sc = USBGETSOFTC(dev); int i; if (sc->aue_vendor == USB_VENDOR_ADMTEK && sc->aue_product == USB_PRODUCT_ADMTEK_PEGASUS) { if (phy == 3) #if defined(__FreeBSD__) return (0); #elif defined(__NetBSD__) || defined(__OpenBSD__) return; #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ } DPRINTFN(11,("%s: %s: phy=%d reg=%d data=0x%04x\n", USBDEVNAME(sc->aue_dev), __FUNCTION__, phy, reg, data)); csr_write_2(sc, AUE_PHY_DATA, data); csr_write_1(sc, AUE_PHY_ADDR, phy); csr_write_1(sc, AUE_PHY_CTL, reg | AUE_PHYCTL_WRITE); for (i = 0; i < AUE_TIMEOUT; i++) { if (csr_read_1(sc, AUE_PHY_CTL) & AUE_PHYCTL_DONE) break; } if (i == AUE_TIMEOUT) { printf("%s: MII read timed out\n", USBDEVNAME(sc->aue_dev)); } #if defined(__FreeBSD__) return (0); #endif } static void aue_miibus_statchg(dev) device_ptr_t dev; { struct aue_softc *sc = USBGETSOFTC(dev); struct mii_data *mii = GET_MII(sc); struct ifnet *ifp = GET_IFP(sc); DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB); if (IFM_SUBTYPE(mii->mii_media_active) == IFM_100_TX) { AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL); ifp->if_baudrate = 100000000; } else { AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_SPEEDSEL); ifp->if_baudrate = 10000000; } if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX) AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX); else AUE_CLRBIT(sc, AUE_CTL1, AUE_CTL1_DUPLEX); AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_RX_ENB | AUE_CTL0_TX_ENB); /* * Set the LED modes on the LinkSys adapter. * This turns on the 'dual link LED' bin in the auxmode * register of the Broadcom PHY. */ if (sc->aue_vendor == USB_VENDOR_LINKSYS && sc->aue_product == USB_PRODUCT_LINKSYS_USB100TX) { u_int16_t auxmode; auxmode = aue_miibus_readreg(dev, 0, 0x1b); aue_miibus_writereg(dev, 0, 0x1b, auxmode | 0x04); } } #define AUE_POLY 0xEDB88320 #define AUE_BITS 6 static u_int32_t aue_crc(addr) caddr_t addr; { u_int32_t idx, bit, data, crc; /* Compute CRC for the address value. */ crc = 0xFFFFFFFF; /* initial value */ for (idx = 0; idx < 6; idx++) { for (data = *addr++, bit = 0; bit < 8; bit++, data >>= 1) crc = (crc >> 1) ^ (((crc ^ data) & 1) ? AUE_POLY : 0); } return (crc & ((1 << AUE_BITS) - 1)); } static void aue_setmulti(sc) struct aue_softc *sc; { struct ifnet *ifp; #if defined(__FreeBSD__) struct ifmultiaddr *ifma; #elif defined(__NetBSD__) || defined(__OpenBSD__) struct ether_multi *enm; struct ether_multistep step; #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ u_int32_t h = 0, i; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); ifp = GET_IFP(sc); if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) { AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); return; } AUE_CLRBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); /* first, zot all the existing hash bits */ for (i = 0; i < 8; i++) csr_write_1(sc, AUE_MAR0 + i, 0); /* now program new ones */ #if defined(__FreeBSD__) for (ifma = ifp->if_multiaddrs.lh_first; ifma != NULL; ifma = ifma->ifma_link.le_next) { if (ifma->ifma_addr->sa_family != AF_LINK) continue; h = aue_crc(LLADDR((struct sockaddr_dl *)ifma->ifma_addr)); AUE_SETBIT(sc, AUE_MAR + (h >> 3), 1 << (h & 0xF)); } #elif defined(__NetBSD__) || defined(__OpenBSD__) ETHER_FIRST_MULTI(step, &sc->aue_ec, enm); while (enm != NULL) { #if 1 if (memcmp(enm->enm_addrlo, enm->enm_addrhi, ETHER_ADDR_LEN) != 0) { ifp->if_flags |= IFF_ALLMULTI; AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_ALLMULTI); return; } #endif h = aue_crc(enm->enm_addrlo); AUE_SETBIT(sc, AUE_MAR + (h >> 3), 1 << (h & 0xF)); ETHER_NEXT_MULTI(step, enm); } #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ } static void aue_reset(sc) struct aue_softc *sc; { int i; DPRINTFN(2,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); AUE_SETBIT(sc, AUE_CTL1, AUE_CTL1_RESETMAC); for (i = 0; i < AUE_TIMEOUT; i++) { if (!(csr_read_1(sc, AUE_CTL1) & AUE_CTL1_RESETMAC)) break; } if (i == AUE_TIMEOUT) printf("%s: reset failed\n", USBDEVNAME(sc->aue_dev)); /* * The PHY(s) attached to the Pegasus chip may be held * in reset until we flip on the GPIO outputs. Make sure * to set the GPIO pins high so that the PHY(s) will * be enabled. * * Note: We force all of the GPIO pins low first, *then* * enable the ones we want. */ csr_write_1(sc, AUE_GPIO0, AUE_GPIO_OUT0|AUE_GPIO_SEL0); csr_write_1(sc, AUE_GPIO0, AUE_GPIO_OUT0|AUE_GPIO_SEL0|AUE_GPIO_SEL1); /* Grrr. LinkSys has to be different from everyone else. */ if (sc->aue_vendor == USB_VENDOR_LINKSYS && sc->aue_product == USB_PRODUCT_LINKSYS_USB100TX) { csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1); csr_write_1(sc, AUE_GPIO0, AUE_GPIO_SEL0|AUE_GPIO_SEL1| AUE_GPIO_OUT0); } /* Wait a little while for the chip to get its brains in order. */ DELAY(10000); /* XXX */ } /* * Probe for a Pegasus chip. */ USB_MATCH(aue) { USB_MATCH_START(aue, uaa); struct aue_type *t; if (uaa->iface != NULL) return (UMATCH_NONE); for (t = aue_devs; t->aue_vid != 0; t++) if (uaa->vendor == t->aue_vid && uaa->product == t->aue_did) return (UMATCH_VENDOR_PRODUCT); return (UMATCH_NONE); } /* * Attach the interface. Allocate softc structures, do ifmedia * setup and ethernet/BPF attach. */ USB_ATTACH(aue) { USB_ATTACH_START(aue, sc, uaa); char devinfo[1024]; int s; u_char eaddr[ETHER_ADDR_LEN]; struct ifnet *ifp; struct mii_data *mii; usbd_device_handle dev = uaa->device; usbd_interface_handle iface; usbd_status err; usb_interface_descriptor_t *id; usb_endpoint_descriptor_t *ed; int i; #ifdef __FreeBSD__ bzero(sc, sizeof(struct aue_softc)); #endif DPRINTFN(5,(" : aue_attach: sc=%p", sc)); usbd_devinfo(dev, 0, devinfo); USB_ATTACH_SETUP; printf("%s: %s\n", USBDEVNAME(sc->aue_dev), devinfo); err = usbd_set_config_no(dev, AUE_CONFIG_NO, 0); if (err) { printf("%s: setting config no failed\n", USBDEVNAME(sc->aue_dev)); USB_ATTACH_ERROR_RETURN; } err = usbd_device2interface_handle(dev, AUE_IFACE_IDX, &iface); if (err) { printf("%s: getting interface handle failed\n", USBDEVNAME(sc->aue_dev)); USB_ATTACH_ERROR_RETURN; } sc->aue_udev = dev; sc->aue_iface = iface; sc->aue_product = uaa->product; sc->aue_vendor = uaa->vendor; id = usbd_get_interface_descriptor(iface); /* Find endpoints. */ for (i = 0; i < id->bNumEndpoints; i++) { ed = usbd_interface2endpoint_descriptor(iface, i); if (!ed) { printf("%s: couldn't get endpoint descriptor %d\n", USBDEVNAME(sc->aue_dev), i); USB_ATTACH_ERROR_RETURN; } if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN && (ed->bmAttributes & UE_XFERTYPE) == UE_BULK) { sc->aue_ed[AUE_ENDPT_RX] = ed->bEndpointAddress; } else if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_OUT && (ed->bmAttributes & UE_XFERTYPE) == UE_BULK) { sc->aue_ed[AUE_ENDPT_TX] = ed->bEndpointAddress; } else if (UE_GET_DIR(ed->bEndpointAddress) == UE_DIR_IN && (ed->bmAttributes & UE_XFERTYPE) == UE_INTERRUPT) { sc->aue_ed[AUE_ENDPT_INTR] = ed->bEndpointAddress; } } if (sc->aue_ed[AUE_ENDPT_RX] == 0 || sc->aue_ed[AUE_ENDPT_TX] == 0 || sc->aue_ed[AUE_ENDPT_INTR] == 0) { printf("%s: missing endpoint\n", USBDEVNAME(sc->aue_dev)); USB_ATTACH_ERROR_RETURN; } s = splimp(); /* Reset the adapter. */ aue_reset(sc); /* * Get station address from the EEPROM. */ aue_read_mac(sc, eaddr); /* * A Pegasus chip was detected. Inform the world. */ #if defined(__FreeBSD__) printf("%s: Ethernet address: %6D\n", USBDEVNAME(sc->aue_dev), eaddr, ":"); bcopy(eaddr, (char *)&sc->arpcom.ac_enaddr, ETHER_ADDR_LEN); ifp = &sc->arpcom.ac_if; ifp->if_softc = sc; ifp->if_unit = sc->aue_unit; ifp->if_name = "aue"; ifp->if_mtu = ETHERMTU; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_ioctl = aue_ioctl; ifp->if_output = ether_output; ifp->if_start = aue_start; ifp->if_watchdog = aue_watchdog; ifp->if_init = aue_init; ifp->if_baudrate = 10000000; ifp->if_snd.ifq_maxlen = IFQ_MAXLEN; /* * Do MII setup. * NOTE: Doing this causes child devices to be attached to us, * which we would normally disconnect at in the detach routine * using device_delete_child(). However the USB code is set up * such that when this driver is removed, all childred devices * are removed as well. In effect, the USB code ends up detaching * all of our children for us, so we don't have to do is ourselves * in aue_detach(). It's important to point this out since if * we *do* try to detach the child devices ourselves, we will * end up getting the children deleted twice, which will crash * the system. */ if (mii_phy_probe(self, &sc->aue_miibus, aue_ifmedia_upd, aue_ifmedia_sts)) { printf("%s: MII without any PHY!\n", USBDEVNAME(sc->aue_dev)); splx(s); USB_ATTACH_ERROR_RETURN; } aue_qdat.ifp = ifp; aue_qdat.if_rxstart = aue_rxstart; /* * Call MI attach routines. */ if_attach(ifp); ether_ifattach(ifp); callout_handle_init(&sc->aue_stat_ch); bpfattach(ifp, DLT_EN10MB, sizeof(struct ether_header)); usb_register_netisr(); #elif defined(__NetBSD__) || defined(__OpenBSD__) printf("%s: Ethernet address %s\n", USBDEVNAME(sc->aue_dev), ether_sprintf(eaddr)); /* Initialize interface info.*/ ifp = &sc->aue_ec.ec_if; ifp->if_softc = sc; ifp->if_mtu = ETHERMTU; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_ioctl = aue_ioctl; ifp->if_start = aue_start; ifp->if_watchdog = aue_watchdog; ifp->if_baudrate = 10000000; strncpy(ifp->if_xname, USBDEVNAME(sc->aue_dev), IFNAMSIZ); /* Initialize MII/media info. */ mii = &sc->aue_mii; mii->mii_ifp = ifp; mii->mii_readreg = aue_miibus_readreg; mii->mii_writereg = aue_miibus_writereg; mii->mii_statchg = aue_miibus_statchg; ifmedia_init(&mii->mii_media, 0, aue_ifmedia_upd, aue_ifmedia_sts); mii_phy_probe(self, mii, 0xffffffff, MII_PHY_ANY, MII_OFFSET_ANY); if (LIST_FIRST(&mii->mii_phys) == NULL) { ifmedia_add(&mii->mii_media, IFM_ETHER | IFM_NONE, 0, NULL); ifmedia_set(&mii->mii_media, IFM_ETHER | IFM_NONE); } else ifmedia_set(&mii->mii_media, IFM_ETHER | IFM_AUTO); /* Attach the interface. */ if_attach(ifp); ether_ifattach(ifp, eaddr); #if NBPFILTER > 0 bpfattach(&ifp->if_bpf, ifp, DLT_EN10MB, sizeof(struct ether_header)); #endif #if RND > 0 rnd_attach_source(&sc->rnd_source, USBDEVNAME(sc->aue_dev), RND_TYPE_NET, 0); #endif #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ splx(s); USB_ATTACH_SUCCESS_RETURN; } USB_DETACH(aue) { USB_DETACH_START(aue, sc); #if defined(__FreeBSD__) struct ifnet *ifp; int s; DPRINTFN(2,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); s = splusb(); ifp = &sc->arpcom.ac_if; usb_untimeout(aue_tick, sc, sc->aue_stat_ch); if_detach(ifp); if (sc->aue_ep[AUE_ENDPT_TX] != NULL) usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_TX]); if (sc->aue_ep[AUE_ENDPT_RX] != NULL) usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_RX]); if (sc->aue_ep[AUE_ENDPT_INTR] != NULL) usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_INTR]); splx(s); return (0); #elif defined(__NetBSD__) || defined(__OpenBSD__) sc = sc; /* XXX use sc */ /* XXX deallocate */ #ifdef notyet /* * Our softc is about to go away, so drop our refernce * to the ifnet. */ if_delref(sc->aue_ec.ec_if); #else return (0); #endif #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ } #if defined(__NetBSD__) || defined(__OpenBSD__) int aue_activate(self, act) device_ptr_t self; enum devact act; { struct aue_softc *sc = (struct aue_softc *)self; DPRINTFN(2,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); switch (act) { case DVACT_ACTIVATE: return (EOPNOTSUPP); break; case DVACT_DEACTIVATE: #ifdef notyet /* First, kill off the interface. */ if_detach(sc->aue_ec.ec_if); #endif sc->aue_dying = 1; break; } return (0); } #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ /* * Initialize an RX descriptor and attach an MBUF cluster. */ static int aue_newbuf(sc, c, m) struct aue_softc *sc; struct aue_chain *c; struct mbuf *m; { struct mbuf *m_new = NULL; DPRINTFN(10,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); if (m == NULL) { MGETHDR(m_new, M_DONTWAIT, MT_DATA); if (m_new == NULL) { printf("%s: no memory for rx list " "-- packet dropped!\n", USBDEVNAME(sc->aue_dev)); return (ENOBUFS); } MCLGET(m_new, M_DONTWAIT); if (!(m_new->m_flags & M_EXT)) { printf("%s: no memory for rx list " "-- packet dropped!\n", USBDEVNAME(sc->aue_dev)); m_freem(m_new); return (ENOBUFS); } m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; } else { m_new = m; m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; m_new->m_data = m_new->m_ext.ext_buf; } m_adj(m_new, ETHER_ALIGN); c->aue_mbuf = m_new; return (0); } static int aue_rx_list_init(sc) struct aue_softc *sc; { struct aue_cdata *cd; struct aue_chain *c; int i; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); cd = &sc->aue_cdata; for (i = 0; i < AUE_RX_LIST_CNT; i++) { c = &cd->aue_rx_chain[i]; c->aue_sc = sc; c->aue_idx = i; c->aue_accum = 0; if (aue_newbuf(sc, c, NULL) == ENOBUFS) return (ENOBUFS); if (c->aue_xfer == NULL) { c->aue_xfer = usbd_alloc_xfer(sc->aue_udev); if (c->aue_xfer == NULL) return (ENOBUFS); c->aue_buf = usbd_alloc_buffer(c->aue_xfer, AUE_BUFSZ); if (c->aue_buf == NULL) return (ENOBUFS); /* XXX free xfer */ } } return (0); } static int aue_tx_list_init(sc) struct aue_softc *sc; { struct aue_cdata *cd; struct aue_chain *c; int i; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); cd = &sc->aue_cdata; for (i = 0; i < AUE_TX_LIST_CNT; i++) { c = &cd->aue_tx_chain[i]; c->aue_sc = sc; c->aue_idx = i; c->aue_mbuf = NULL; if (c->aue_xfer == NULL) { c->aue_xfer = usbd_alloc_xfer(sc->aue_udev); if (c->aue_xfer == NULL) return (ENOBUFS); c->aue_buf = usbd_alloc_buffer(c->aue_xfer, AUE_BUFSZ); if (c->aue_buf == NULL) return (ENOBUFS); } } return (0); } static void aue_intr(xfer, priv, status) usbd_xfer_handle xfer; usbd_private_handle priv; usbd_status status; { struct aue_softc *sc = priv; struct ifnet *ifp = GET_IFP(sc); struct aue_intrpkt *p = &sc->aue_cdata.aue_ibuf; DPRINTFN(15,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); if (!(ifp->if_flags & IFF_RUNNING)) return; if (status != USBD_NORMAL_COMPLETION) { if (status == USBD_NOT_STARTED || status == USBD_CANCELLED) { return; } printf("%s: usb error on intr: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(status)); if (status == USBD_STALLED) usbd_clear_endpoint_stall(sc->aue_ep[AUE_ENDPT_RX]); return; } if (p->aue_txstat0) ifp->if_oerrors++; if (p->aue_txstat0 & (AUE_TXSTAT0_LATECOLL | AUE_TXSTAT0_EXCESSCOLL)) ifp->if_collisions++; } #if defined(__FreeBSD__) static void aue_rxstart(ifp) struct ifnet *ifp; { struct aue_softc *sc; struct aue_chain *c; sc = ifp->if_softc; c = &sc->aue_cdata.aue_rx_chain[sc->aue_cdata.aue_rx_prod]; if (aue_newbuf(sc, c, NULL) == ENOBUFS) { ifp->if_ierrors++; return; } /* Setup new transfer. */ usbd_setup_xfer(c->aue_xfer, sc->aue_ep[AUE_ENDPT_RX], c, mtod(c->aue_mbuf, char *), AUE_CUTOFF, USBD_SHORT_XFER_OK, USBD_NO_TIMEOUT, aue_rxeof); usbd_transfer(c->aue_xfer); } #endif /* * A frame has been uploaded: pass the resulting mbuf chain up to * the higher level protocols. * * Grrr. Receiving transfers larger than about 1152 bytes sometimes * doesn't work. We get an incomplete frame. In order to avoid * this, we queue up RX transfers that are shorter than a full sized * frame. If the received frame is larger than our transfer size, * we snag the rest of the data using a second transfer. Does this * hurt performance? Yes. But after fighting with this stupid thing * for three days, I'm willing to settle. I'd rather have reliable * receive performance that fast but spotty performance. */ static void aue_rxeof(xfer, priv, status) usbd_xfer_handle xfer; usbd_private_handle priv; usbd_status status; { struct aue_chain *c = priv; struct aue_softc *sc = c->aue_sc; struct ifnet *ifp = GET_IFP(sc); struct mbuf *m; u_int32_t total_len; struct aue_rxpkt r; #if defined(__NetBSD__) || defined(__OpenBSD__) int s; #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ DPRINTFN(10,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); if (!(ifp->if_flags & IFF_RUNNING)) return; if (status != USBD_NORMAL_COMPLETION) { if (status == USBD_NOT_STARTED || status == USBD_CANCELLED) return; printf("%s: usb error on rx: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(status)); if (status == USBD_STALLED) usbd_clear_endpoint_stall(sc->aue_ep[AUE_ENDPT_RX]); goto done; } usbd_get_xfer_status(xfer, NULL, NULL, &total_len, NULL); /* XXX copy data to mbuf */ memcpy(mtod(c->aue_mbuf, char*) + c->aue_accum, c->aue_buf, total_len); /* * See if we've already accumulated some data from * a previous transfer. */ if (c->aue_accum) { total_len += c->aue_accum; c->aue_accum = 0; } if (total_len <= 4 + ETHER_CRC_LEN) { ifp->if_ierrors++; goto done; } m = c->aue_mbuf; memcpy(&r, mtod(m, char *) + total_len - 4, sizeof(r)); /* Turn off all the non-error bits in the rx status word. */ r.aue_rxstat &= AUE_RXSTAT_MASK; /* * Check to see if this is just the first chunk of a * split transfer. We really need a more reliable way * to detect this. */ if (UGETW(r.aue_pktlen) != total_len && total_len == AUE_CUTOFF) { c->aue_accum = AUE_CUTOFF; usbd_setup_xfer(xfer, sc->aue_ep[AUE_ENDPT_RX], c, c->aue_buf, AUE_CUTOFF, USBD_SHORT_XFER_OK | USBD_NO_COPY, USBD_NO_TIMEOUT, aue_rxeof); DPRINTFN(5,("%s: %s: extra rx\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); usbd_transfer(xfer); return; } if (r.aue_rxstat) { ifp->if_ierrors++; goto done; } /* No errors; receive the packet. */ total_len -= ETHER_CRC_LEN + 4; m->m_pkthdr.len = m->m_len = total_len; ifp->if_ipackets++; #if defined(__FreeBSD__) m->m_pkthdr.rcvif = (struct ifnet *)&kue_qdat; /* Put the packet on the special USB input queue. */ usb_ether_input(m); return; #elif defined(__NetBSD__) || defined(__OpenBSD__) m->m_pkthdr.rcvif = ifp; s = splimp(); /* XXX ugly */ if (aue_newbuf(sc, c, NULL) == ENOBUFS) { ifp->if_ierrors++; goto done1; } /* * Handle BPF listeners. Let the BPF user see the packet, but * don't pass it up to the ether_input() layer unless it's * a broadcast packet, multicast packet, matches our ethernet * address or the interface is in promiscuous mode. */ if (ifp->if_bpf) { struct ether_header *eh = mtod(m, struct ether_header *); bpf_mtap(ifp, m); if ((ifp->if_flags & IFF_PROMISC) && memcmp(eh->ether_dhost, LLADDR(ifp->if_sadl), ETHER_ADDR_LEN) && !(eh->ether_dhost[0] & 1)) { m_freem(m); goto done1; } } DPRINTFN(10,("%s: %s: deliver %d\n", USBDEVNAME(sc->aue_dev), __FUNCTION__, m->m_len)); (*ifp->if_input)(ifp, m); done1: splx(s); #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ done: /* Setup new transfer. */ usbd_setup_xfer(xfer, sc->aue_ep[AUE_ENDPT_RX], c, c->aue_buf, AUE_CUTOFF, USBD_SHORT_XFER_OK | USBD_NO_COPY, USBD_NO_TIMEOUT, aue_rxeof); usbd_transfer(xfer); DPRINTFN(10,("%s: %s: start rx\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); } /* * A frame was downloaded to the chip. It's safe for us to clean up * the list buffers. */ static void aue_txeof(xfer, priv, status) usbd_xfer_handle xfer; usbd_private_handle priv; usbd_status status; { struct aue_chain *c = priv; struct aue_softc *sc = c->aue_sc; struct ifnet *ifp = GET_IFP(sc); int s; s = splimp(); DPRINTFN(10,("%s: %s: enter status=%d\n", USBDEVNAME(sc->aue_dev), __FUNCTION__, status)); ifp->if_timer = 0; ifp->if_flags &= ~IFF_OACTIVE; if (status != USBD_NORMAL_COMPLETION) { if (status == USBD_NOT_STARTED || status == USBD_CANCELLED) { splx(s); return; } ifp->if_oerrors++; printf("%s: usb error on tx: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(status)); if (status == USBD_STALLED) usbd_clear_endpoint_stall(sc->aue_ep[AUE_ENDPT_TX]); splx(s); return; } ifp->if_opackets++; #if defined(__FreeBSD__) c->aue_mbuf->m_pkthdr.rcvif = ifp; usb_tx_done(c->aue_mbuf); c->aue_mbuf = NULL; #elif defined(__NetBSD__) || defined(__OpenBSD__) m_freem(c->aue_mbuf); c->aue_mbuf = NULL; if (ifp->if_snd.ifq_head != NULL) aue_start(ifp); #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ splx(s); } static void aue_tick(xsc) void *xsc; { struct aue_softc *sc = xsc; struct ifnet *ifp; struct mii_data *mii; int s; DPRINTFN(15,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); if (sc == NULL) return; ifp = GET_IFP(sc); mii = GET_MII(sc); if (mii == NULL) return; s = splimp(); mii_tick(mii); if (!sc->aue_link) { mii_pollstat(mii); if (mii->mii_media_status & IFM_ACTIVE && IFM_SUBTYPE(mii->mii_media_active) != IFM_NONE) { DPRINTFN(2,("%s: %s: got link\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); sc->aue_link++; if (ifp->if_snd.ifq_head != NULL) aue_start(ifp); } } usb_timeout(aue_tick, sc, hz, sc->aue_stat_ch); splx(s); } static int aue_send(sc, m, idx) struct aue_softc *sc; struct mbuf *m; int idx; { int total_len; struct aue_chain *c; usbd_status err; DPRINTFN(10,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev),__FUNCTION__)); c = &sc->aue_cdata.aue_tx_chain[idx]; /* * Copy the mbuf data into a contiguous buffer, leaving two * bytes at the beginning to hold the frame length. */ m_copydata(m, 0, m->m_pkthdr.len, c->aue_buf + 2); c->aue_mbuf = m; /* * The ADMtek documentation says that the packet length is * supposed to be specified in the first two bytes of the * transfer, however it actually seems to ignore this info * and base the frame size on the bulk transfer length. */ c->aue_buf[0] = (u_int8_t)m->m_pkthdr.len; c->aue_buf[1] = (u_int8_t)(m->m_pkthdr.len >> 8); total_len = m->m_pkthdr.len + 2; usbd_setup_xfer(c->aue_xfer, sc->aue_ep[AUE_ENDPT_TX], c, c->aue_buf, total_len, USBD_FORCE_SHORT_XFER | USBD_NO_COPY, AUE_TX_TIMEOUT, aue_txeof); /* Transmit */ err = usbd_transfer(c->aue_xfer); if (err != USBD_IN_PROGRESS) { aue_stop(sc); return (EIO); } DPRINTFN(5,("%s: %s: send %d bytes\n", USBDEVNAME(sc->aue_dev), __FUNCTION__, total_len)); sc->aue_cdata.aue_tx_cnt++; return (0); } static void aue_start(ifp) struct ifnet *ifp; { struct aue_softc *sc = ifp->if_softc; struct mbuf *m_head = NULL; DPRINTFN(5,("%s: %s: enter, link=%d\n", USBDEVNAME(sc->aue_dev), __FUNCTION__, sc->aue_link)); if (!sc->aue_link) return; if (ifp->if_flags & IFF_OACTIVE) return; IF_DEQUEUE(&ifp->if_snd, m_head); if (m_head == NULL) return; if (aue_send(sc, m_head, 0)) { IF_PREPEND(&ifp->if_snd, m_head); ifp->if_flags |= IFF_OACTIVE; return; } /* * If there's a BPF listener, bounce a copy of this frame * to him. */ if (ifp->if_bpf) bpf_mtap(ifp, m_head); ifp->if_flags |= IFF_OACTIVE; /* * Set a timeout in case the chip goes out to lunch. */ ifp->if_timer = 5; } static void aue_init(xsc) void *xsc; { struct aue_softc *sc = xsc; struct ifnet *ifp = GET_IFP(sc); struct mii_data *mii = GET_MII(sc); struct aue_chain *c; usbd_status err; int i, s; u_char *eaddr; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); if (ifp->if_flags & IFF_RUNNING) return; s = splimp(); /* * Cancel pending I/O and free all RX/TX buffers. */ aue_reset(sc); #if defined(__FreeBSD__) eaddr = sc->arpcom.ac_enaddr; #elif defined(__NetBSD__) || defined(__OpenBSD__) eaddr = LLADDR(ifp->if_sadl); #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ for (i = 0; i < ETHER_ADDR_LEN; i++) csr_write_1(sc, AUE_PAR0 + i, eaddr[i]); /* If we want promiscuous mode, set the allframes bit. */ if (ifp->if_flags & IFF_PROMISC) AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); else AUE_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); /* Init TX ring. */ if (aue_tx_list_init(sc) == ENOBUFS) { printf("%s: tx list init failed\n", USBDEVNAME(sc->aue_dev)); splx(s); return; } /* Init RX ring. */ if (aue_rx_list_init(sc) == ENOBUFS) { printf("%s: rx list init failed\n", USBDEVNAME(sc->aue_dev)); splx(s); return; } /* Load the multicast filter. */ aue_setmulti(sc); /* Enable RX and TX */ csr_write_1(sc, AUE_CTL0, AUE_CTL0_RXSTAT_APPEND|AUE_CTL0_RX_ENB); AUE_SETBIT(sc, AUE_CTL0, AUE_CTL0_TX_ENB); AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_EP3_CLR); mii_mediachg(mii); if (sc->aue_ep[AUE_ENDPT_RX] == NULL) { /* Open RX and TX pipes. */ err = usbd_open_pipe(sc->aue_iface, sc->aue_ed[AUE_ENDPT_RX], USBD_EXCLUSIVE_USE, &sc->aue_ep[AUE_ENDPT_RX]); if (err) { printf("%s: open rx pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); splx(s); return; } usbd_open_pipe(sc->aue_iface, sc->aue_ed[AUE_ENDPT_TX], USBD_EXCLUSIVE_USE, &sc->aue_ep[AUE_ENDPT_TX]); if (err) { printf("%s: open tx pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); splx(s); return; } err = usbd_open_pipe_intr(sc->aue_iface, sc->aue_ed[AUE_ENDPT_INTR], USBD_EXCLUSIVE_USE, &sc->aue_ep[AUE_ENDPT_INTR], sc, &sc->aue_cdata.aue_ibuf, AUE_INTR_PKTLEN, aue_intr); if (err) { printf("%s: open intr pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); splx(s); return; } /* Start up the receive pipe. */ for (i = 0; i < AUE_RX_LIST_CNT; i++) { c = &sc->aue_cdata.aue_rx_chain[i]; usbd_setup_xfer(c->aue_xfer, sc->aue_ep[AUE_ENDPT_RX], c, c->aue_buf, AUE_CUTOFF, USBD_SHORT_XFER_OK | USBD_NO_COPY, USBD_NO_TIMEOUT, aue_rxeof); usbd_transfer(c->aue_xfer); DPRINTFN(5,("%s: %s: start read\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); } } ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; splx(s); usb_untimeout(aue_tick, sc, sc->aue_stat_ch); usb_timeout(aue_tick, sc, hz, sc->aue_stat_ch); } /* * Set media options. */ static int aue_ifmedia_upd(ifp) struct ifnet *ifp; { struct aue_softc *sc = ifp->if_softc; struct mii_data *mii = GET_MII(sc); DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); sc->aue_link = 0; if (mii->mii_instance) { struct mii_softc *miisc; for (miisc = LIST_FIRST(&mii->mii_phys); miisc != NULL; miisc = LIST_NEXT(miisc, mii_list)) mii_phy_reset(miisc); } mii_mediachg(mii); return (0); } /* * Report current media status. */ static void aue_ifmedia_sts(ifp, ifmr) struct ifnet *ifp; struct ifmediareq *ifmr; { struct aue_softc *sc = ifp->if_softc; struct mii_data *mii = GET_MII(sc); DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); mii_pollstat(mii); ifmr->ifm_active = mii->mii_media_active; ifmr->ifm_status = mii->mii_media_status; } static int aue_ioctl(ifp, command, data) struct ifnet *ifp; u_long command; caddr_t data; { struct aue_softc *sc = ifp->if_softc; #if defined(__NetBSD__) || defined(__OpenBSD__) struct ifaddr *ifa = (struct ifaddr *)data; #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ struct ifreq *ifr = (struct ifreq *)data; struct mii_data *mii; int s, error = 0; s = splimp(); switch(command) { #if defined(__FreeBSD__) case SIOCSIFADDR: case SIOCGIFADDR: case SIOCSIFMTU: error = ether_ioctl(ifp, command, data); break; #elif defined(__NetBSD__) || defined(__OpenBSD__) case SIOCSIFADDR: ifp->if_flags |= IFF_UP; aue_init(sc); switch (ifa->ifa_addr->sa_family) { #ifdef INET case AF_INET: arp_ifinit(ifp, ifa); break; #endif /* INET */ #ifdef NS case AF_NS: { struct ns_addr *ina = &IA_SNS(ifa)->sns_addr; if (ns_nullhost(*ina)) ina->x_host = *(union ns_host *) LLADDR(ifp->if_sadl); else memcpy(LLADDR(ifp->if_sadl), ina->x_host.c_host, ifp->if_addrlen); break; } #endif /* NS */ } break; case SIOCSIFMTU: if (ifr->ifr_mtu > ETHERMTU) error = EINVAL; else ifp->if_mtu = ifr->ifr_mtu; break; #endif /* defined(__NetBSD__) || defined(__OpenBSD__) */ case SIOCSIFFLAGS: if (ifp->if_flags & IFF_UP) { if (ifp->if_flags & IFF_RUNNING && ifp->if_flags & IFF_PROMISC && !(sc->aue_if_flags & IFF_PROMISC)) { AUE_SETBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); } else if (ifp->if_flags & IFF_RUNNING && !(ifp->if_flags & IFF_PROMISC) && sc->aue_if_flags & IFF_PROMISC) { AUE_CLRBIT(sc, AUE_CTL2, AUE_CTL2_RX_PROMISC); } else if (!(ifp->if_flags & IFF_RUNNING)) aue_init(sc); } else { if (ifp->if_flags & IFF_RUNNING) aue_stop(sc); } sc->aue_if_flags = ifp->if_flags; error = 0; break; case SIOCADDMULTI: case SIOCDELMULTI: aue_setmulti(sc); error = 0; break; case SIOCGIFMEDIA: case SIOCSIFMEDIA: mii = GET_MII(sc); error = ifmedia_ioctl(ifp, ifr, &mii->mii_media, command); break; default: error = EINVAL; break; } splx(s); return (error); } static void aue_watchdog(ifp) struct ifnet *ifp; { struct aue_softc *sc = ifp->if_softc; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); ifp->if_oerrors++; printf("%s: watchdog timeout\n", USBDEVNAME(sc->aue_dev)); /* * The polling business is a kludge to avoid allowing the * USB code to call tsleep() in usbd_delay_ms(), which will * kill us since the watchdog routine is invoked from * interrupt context. */ usbd_set_polling(sc->aue_udev, 1); aue_stop(sc); aue_init(sc); usbd_set_polling(sc->aue_udev, 0); if (ifp->if_snd.ifq_head != NULL) aue_start(ifp); } /* * Stop the adapter and free any mbufs allocated to the * RX and TX lists. */ static void aue_stop(sc) struct aue_softc *sc; { usbd_status err; struct ifnet *ifp; int i; DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); ifp = GET_IFP(sc); ifp->if_timer = 0; csr_write_1(sc, AUE_CTL0, 0); csr_write_1(sc, AUE_CTL1, 0); aue_reset(sc); usb_untimeout(aue_tick, sc, sc->aue_stat_ch); /* Stop transfers. */ if (sc->aue_ep[AUE_ENDPT_RX] != NULL) { err = usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_RX]); if (err) { printf("%s: abort rx pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); } err = usbd_close_pipe(sc->aue_ep[AUE_ENDPT_RX]); if (err) { printf("%s: close rx pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); } sc->aue_ep[AUE_ENDPT_RX] = NULL; } if (sc->aue_ep[AUE_ENDPT_TX] != NULL) { err = usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_TX]); if (err) { printf("%s: abort tx pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); } err = usbd_close_pipe(sc->aue_ep[AUE_ENDPT_TX]); if (err) { printf("%s: close tx pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); } sc->aue_ep[AUE_ENDPT_TX] = NULL; } if (sc->aue_ep[AUE_ENDPT_INTR] != NULL) { err = usbd_abort_pipe(sc->aue_ep[AUE_ENDPT_INTR]); if (err) { printf("%s: abort intr pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); } err = usbd_close_pipe(sc->aue_ep[AUE_ENDPT_INTR]); if (err) { printf("%s: close intr pipe failed: %s\n", USBDEVNAME(sc->aue_dev), usbd_errstr(err)); } sc->aue_ep[AUE_ENDPT_INTR] = NULL; } /* Free RX resources. */ for (i = 0; i < AUE_RX_LIST_CNT; i++) { if (sc->aue_cdata.aue_rx_chain[i].aue_mbuf != NULL) { m_freem(sc->aue_cdata.aue_rx_chain[i].aue_mbuf); sc->aue_cdata.aue_rx_chain[i].aue_mbuf = NULL; } if (sc->aue_cdata.aue_rx_chain[i].aue_xfer != NULL) { usbd_free_xfer(sc->aue_cdata.aue_rx_chain[i].aue_xfer); sc->aue_cdata.aue_rx_chain[i].aue_xfer = NULL; } } /* Free TX resources. */ for (i = 0; i < AUE_TX_LIST_CNT; i++) { if (sc->aue_cdata.aue_tx_chain[i].aue_mbuf != NULL) { m_freem(sc->aue_cdata.aue_tx_chain[i].aue_mbuf); sc->aue_cdata.aue_tx_chain[i].aue_mbuf = NULL; } if (sc->aue_cdata.aue_tx_chain[i].aue_xfer != NULL) { usbd_free_xfer(sc->aue_cdata.aue_tx_chain[i].aue_xfer); sc->aue_cdata.aue_tx_chain[i].aue_xfer = NULL; } } sc->aue_link = 0; ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); } #ifdef __FreeBSD__ /* * Stop all chip I/O so that the kernel's probe routines don't * get confused by errant DMAs when rebooting. */ static void aue_shutdown(dev) device_ptr_t dev; { struct aue_softc *sc = USBGETSOFTC(dev); DPRINTFN(5,("%s: %s: enter\n", USBDEVNAME(sc->aue_dev), __FUNCTION__)); aue_reset(sc); aue_stop(sc); } #endif