/* * National Semiconductor DS8390 NIC register definitions * * $Id: if_sereg.h,v 1.1.1.1 1996/05/05 12:17:03 oki Exp $ * * Modification history * * $Log: if_sereg.h,v $ * Revision 1.1.1.1 1996/05/05 12:17:03 oki * NetBSD/x68k, by Masaru Oki. * * Revision 1.1 1995/05/16 19:54:23 oki * *** empty log message *** * * Revision 1.2 1994/03/01 15:24:26 briggs * More Dayna separation. * * Revision 1.1 1993/11/29 00:32:46 briggs * Update to current work in progress. This includes an update to * use config.new. * Numerous updates to console so it works better on the SE/30 screen. * Some nice changes from Brad Parker for handling NuBUS and an ethernet * driver that I haven't worked on, yet. * * */ #define CMD_CLEAR_TALLIES 0x02 #define CMD_SEND_ETHERPACKET 0x05 #define CMD_RECIEVE_ETHERPACKET 0x0e #define CMD_SET_ETHERADDR 0x06 #define CMD_SET_MULTICASTADDR 0x09 #define CMD_SET_PACKETRECEPTMODE 0x0c #define CMD_ETHERNET_RECIEVE 0x0d /* * Page 0 register offsets */ #define SE_P0_CR 0x00 /* Command Register */ #define SE_P0_CLDA0 0x01 /* Current Local DMA Addr low (read) */ #define SE_P0_PSTART 0x01 /* Page Start register (write) */ #define SE_P0_CLDA1 0x02 /* Current Local DMA Addr high (read) */ #define SE_P0_PSTOP 0x02 /* Page Stop register (write) */ #define SE_P0_BNRY 0x03 /* Boundary Pointer */ #define SE_P0_TSR 0x04 /* Transmit Status Register (read) */ #define SE_P0_TPSR 0x04 /* Transmit Page Start (write) */ #define SE_P0_NCR 0x05 /* Number of Collisions Reg (read) */ #define SE_P0_TBCR0 0x05 /* Transmit Byte count, low (write) */ #define SE_P0_FIFO 0x06 /* FIFO register (read) */ #define SE_P0_TBCR1 0x06 /* Transmit Byte count, high (write) */ #define SE_P0_ISR 0x07 /* Interrupt Status Register */ #define SE_P0_CRDA0 0x08 /* Current Remote DMA Addr low (read) */ #define SE_P0_RSAR0 0x08 /* Remote Start Address low (write) */ #define SE_P0_CRDA1 0x09 /* Current Remote DMA Addr high (read) */ #define SE_P0_RSAR1 0x09 /* Remote Start Address high (write) */ #define SE_P0_RBCR0 0x0a /* Remote Byte Count low (write) */ #define SE_P0_RBCR1 0x0b /* Remote Byte Count high (write) */ #define SE_P0_RSR 0x0c /* Receive Status (read) */ #define SE_P0_RCR 0x0c /* Receive Configuration Reg (write) */ #define SE_P0_CNTR0 0x0d /* frame alignment error counter (read) */ #define SE_P0_TCR 0x0d /* Transmit Configuration Reg (write) */ #define SE_P0_CNTR1 0x0e /* CRC error counter (read) */ #define SE_P0_DCR 0x0e /* Data Configuration Reg (write) */ #define SE_P0_CNTR2 0x0f /* missed packet counter (read) */ #define SE_P0_IMR 0x0f /* Interrupt Mask Register (write) */ /* * Page 1 register offsets */ #define SE_P1_CR 0x00 /* Command Register */ #define SE_P1_PAR0 0x01 /* Physical Address Register 0 */ #define SE_P1_PAR1 0x02 /* Physical Address Register 1 */ #define SE_P1_PAR2 0x03 /* Physical Address Register 2 */ #define SE_P1_PAR3 0x04 /* Physical Address Register 3 */ #define SE_P1_PAR4 0x05 /* Physical Address Register 4 */ #define SE_P1_PAR5 0x06 /* Physical Address Register 5 */ #define SE_P1_CURR 0x07 /* Current RX ring-buffer page */ #define SE_P1_MAR0 0x08 /* Multicast Address Register 0 */ #define SE_P1_MAR1 0x09 /* Multicast Address Register 1 */ #define SE_P1_MAR2 0x0a /* Multicast Address Register 2 */ #define SE_P1_MAR3 0x0b /* Multicast Address Register 3 */ #define SE_P1_MAR4 0x0c /* Multicast Address Register 4 */ #define SE_P1_MAR5 0x0d /* Multicast Address Register 5 */ #define SE_P1_MAR6 0x0e /* Multicast Address Register 6 */ #define SE_P1_MAR7 0x0f /* Multicast Address Register 7 */ /* * Page 2 register offsets */ #define SE_P2_CR 0x00 /* Command Register */ #define SE_P2_PSTART 0x01 /* Page Start (read) */ #define SE_P2_CLDA0 0x01 /* Current Local DMA Addr 0 (write) */ #define SE_P2_PSTOP 0x02 /* Page Stop (read) */ #define SE_P2_CLDA1 0x02 /* Current Local DMA Addr 1 (write) */ #define SE_P2_RNPP 0x03 /* Remote Next Packet Pointer */ #define SE_P2_TPSR 0x04 /* Transmit Page Start (read) */ #define SE_P2_LNPP 0x05 /* Local Next Packet Pointer */ #define SE_P2_ACU 0x06 /* Address Counter Upper */ #define SE_P2_ACL 0x07 /* Address Counter Lower */ #define SE_P2_RCR 0x0c /* Receive Configuration Register (read) */ #define SE_P2_TCR 0x0d /* Transmit Configuration Register (read) */ #define SE_P2_DCR 0x0e /* Data Configuration Register (read) */ #define SE_P2_IMR 0x0f /* Interrupt Mask Register (read) */ /* * Command Register (CR) definitions */ /* * STP: SToP. Software reset command. Takes the controller offline. No * packets will be received or transmitted. Any reception or * transmission in progress will continue to completion before * entering reset state. To exit this state, the STP bit must * reset and the STA bit must be set. The software reset has * executed only when indicated by the RST bit in the ISR being * set. */ #define SE_CR_STP 0x01 /* * STA: STArt. This bit is used to activate the NIC after either power-up, * or when the NIC has been put in reset mode by software command * or error. */ #define SE_CR_STA 0x02 /* * TXP: Transmit Packet. This bit must be set to indicate transmission of * a packet. TXP is internally reset either after the transmission is * completed or aborted. This bit should be set only after the Transmit * Byte Count and Transmit Page Start register have been programmed. */ #define SE_CR_TXP 0x04 /* * RD0, RD1, RD2: Remote DMA Command. These three bits control the operation * of the remote DMA channel. RD2 can be set to abort any remote DMA * command in progress. The Remote Byte Count registers should be cleared * when a remote DMA has been aborted. The Remote Start Addresses are not * restored to the starting address if the remote DMA is aborted. * * RD2 RD1 RD0 function * 0 0 0 not allowed * 0 0 1 remote read * 0 1 0 remote write * 0 1 1 send packet * 1 X X abort */ #define SE_CR_RD0 0x08 #define SE_CR_RD1 0x10 #define SE_CR_RD2 0x20 /* * PS0, PS1: Page Select. The two bits select which register set or 'page' to * access. * * PS1 PS0 page * 0 0 0 * 0 1 1 * 1 0 2 * 1 1 reserved */ #define SE_CR_PS0 0x40 #define SE_CR_PS1 0x80 /* bit encoded aliases */ #define SE_CR_PAGE_0 0x00 /* (for consistency) */ #define SE_CR_PAGE_1 0x40 #define SE_CR_PAGE_2 0x80 /* * Interrupt Status Register (ISR) definitions */ /* * PRX: Packet Received. Indicates packet received with no errors. */ #define SE_ISR_PRX 0x01 /* * PTX: Packet Transmitted. Indicates packet transmitted with no errors. */ #define SE_ISR_PTX 0x02 /* * RXE: Receive Error. Indicates that a packet was received with one or more * the following errors: CRC error, frame alignment error, FIFO overrun, * missed packet. */ #define SE_ISR_RXE 0x04 /* * TXE: Transmission Error. Indicates that an attempt to transmit a packet * resulted in one or more of the following errors: excessive * collisions, FIFO underrun. */ #define SE_ISR_TXE 0x08 /* * OVW: OverWrite. Indicates a receive ring-buffer overrun. Incoming network * would exceed (has exceeded?) the boundry pointer, resulting in data * that was previously received and not yet read from the buffer to be * overwritten. */ #define SE_ISR_OVW 0x10 /* * CNT: Counter Overflow. Set when the MSB of one or more of the Network Talley * Counters has been set. */ #define SE_ISR_CNT 0x20 /* * RDC: Remote Data Complete. Indicates that a Remote DMA operation has completed. */ #define SE_ISR_RDC 0x40 /* * RST: Reset status. Set when the NIC enters the reset state and cleared when a * Start Command is issued to the CR. This bit is also set when a receive * ring-buffer overrun (OverWrite) occurs and is cleared when one or more * packets have been removed from the ring. This is a read-only bit. */ #define SE_ISR_RST 0x80 /* * Interrupt Mask Register (IMR) definitions */ /* * PRXE: Packet Received interrupt Enable. If set, a received packet will cause * an interrupt. */ #define SE_IMR_PRXE 0x01 /* * PTXE: Packet Transmit interrupt Enable. If set, an interrupt is generated when * a packet transmission completes. */ #define SE_IMR_PTXE 0x02 /* * RXEE: Receive Error interrupt Enable. If set, an interrupt will occur whenever a * packet is received with an error. */ #define SE_IMR_RXEE 0x04 /* * TXEE: Transmit Error interrupt Enable. If set, an interrupt will occur whenever * a transmission results in an error. */ #define SE_IMR_TXEE 0x08 /* * OVWE: OverWrite error interrupt Enable. If set, an interrupt is generated whenever * the receive ring-buffer is overrun. i.e. when the boundry pointer is exceeded. */ #define SE_IMR_OVWE 0x10 /* * CNTE: Counter overflow interrupt Enable. If set, an interrupt is generated whenever * the MSB of one or more of the Network Statistics counters has been set. */ #define SE_IMR_CNTE 0x20 /* * RDCE: Remote DMA Complete interrupt Enable. If set, an interrupt is generated * when a remote DMA transfer has completed. */ #define SE_IMR_RDCE 0x40 /* * bit 7 is unused/reserved */ /* * Data Configuration Register (DCR) definitions */ /* * WTS: Word Transfer Select. WTS establishes byte or word transfers for * both remote and local DMA transfers */ #define SE_DCR_WTS 0x01 /* * BOS: Byte Order Select. BOS sets the byte order for the host. * Should be 0 for 80x86, and 1 for 68000 series processors */ #define SE_DCR_BOS 0x02 /* * LAS: Long Address Select. When LAS is 1, the contents of the remote * DMA registers RSAR0 and RSAR1 are used to provide A16-A31 */ #define SE_DCR_LAS 0x04 #ifdef huh /* * LS: Loopback Select. When 0, loopback mode is selected. Bits D1 and D2 * of the TCR must also be programmed for loopback operation. * When 1, normal operation is selected. */ #define SE_DCR_LS 0x08 #endif /* * BMS: Burst Mode Select */ #define SE_DCR_BMS 0x08 /* * AR: Auto-initialize Remote. When 0, data must be removed from ring-buffer * under program control. When 1, remote DMA is automatically initiated * and the boundry pointer is automatically updated */ #define SE_DCR_AR 0x10 /* * FT0, FT1: Fifo Threshold select. * FT1 FT0 Word-width Byte-width * 0 0 1 word 2 bytes * 0 1 2 words 4 bytes * 1 0 4 words 8 bytes * 1 1 8 words 12 bytes * * During transmission, the FIFO threshold indicates the number of bytes * or words that the FIFO has filled from the local DMA before BREQ is * asserted. The transmission threshold is 16 bytes minus the receiver * threshold. */ #define SE_DCR_FT0 0x20 #define SE_DCR_FT1 0x40 /* * bit 7 (0x80) is unused/reserved */ /* * Transmit Configuration Register (TCR) definitions */ /* * CRC: Inhibit CRC. If 0, CRC will be appended by the transmitter, if 0, CRC * is not appended by the transmitter. */ #define SE_TCR_CRC 0x01 /* * LB0, LB1: Loopback control. These two bits set the type of loopback that is * to be performed. * * LB1 LB0 mode * 0 0 0 - normal operation (DCR_LS = 0) * 0 1 1 - internal loopback (DCR_LS = 0) * 1 0 2 - external loopback (DCR_LS = 1) * 1 1 3 - external loopback (DCR_LS = 0) */ #define SE_TCR_LB0 0x02 #define SE_TCR_LB1 0x04 /* * ATD: Auto Transmit Disable. Clear for normal operation. When set, allows * another station to disable the NIC's transmitter by transmitting to * a multicast address hashing to bit 62. Reception of a multicast address * hashing to bit 63 enables the transmitter. */ #define SE_TCR_ATD 0x08 /* * OFST: Collision Offset enable. This bit when set modifies the backoff * algorithm to allow prioritization of nodes. */ #define SE_TCR_OFST 0x10 /* * bits 5, 6, and 7 are unused/reserved */ /* * Transmit Status Register (TSR) definitions */ /* * PTX: Packet Transmitted. Indicates successful transmission of packet. */ #define SE_TSR_PTX 0x01 /* * bit 1 (0x02) is unused/reserved */ /* * COL: Transmit Collided. Indicates that the transmission collided at least * once with another station on the network. */ #define SE_TSR_COL 0x04 /* * ABT: Transmit aborted. Indicates that the transmission was aborted due to * excessive collisions. */ #define SE_TSR_ABT 0x08 /* * CRS: Carrier Sense Lost. Indicates that carrier was lost during the * transmission of the packet. (Transmission is not aborted because * of a loss of carrier) */ #define SE_TSR_CRS 0x10 /* * FU: FIFO Underrun. Indicates that the NIC wasn't able to access bus/ * transmission memory before the FIFO emptied. Transmission of the * packet was aborted. */ #define SE_TSR_FU 0x20 /* * CDH: CD Heartbeat. Indicates that the collision detection circuitry * isn't working correctly during a collision heartbeat test. */ #define SE_TSR_CDH 0x40 /* * OWC: Out of Window Collision: Indicates that a collision occurred after * a slot time (51.2us). The transmission is rescheduled just as in * normal collisions. */ #define SE_TSR_OWC 0x80 /* * Receiver Configuration Register (RCR) definitions */ /* * SEP: Save Errored Packets. If 0, error packets are discarded. If set to 1, * packets with CRC and frame errors are not discarded. */ #define SE_RCR_SEP 0x01 /* * AR: Accept Runt packet. If 0, packet with less than 64 byte are discarded. * If set to 1, packets with less than 64 byte are not discarded. */ #define SE_RCR_AR 0x02 /* * AB: Accept Broadcast. If set, packets sent to the broadcast address will be * accepted. */ #define SE_RCR_AB 0x04 /* * AM: Accept Multicast. If set, packets sent to a multicast address are checked * for a match in the hashing array. If clear, multicast packets are ignored. */ #define SE_RCR_AM 0x08 /* * PRO: Promiscuous Physical. If set, all packets with a physical addresses are * accepted. If clear, a physical destination address must match this * station's address. Note: for full promiscuous mode, RCR_AB and RCR_AM * must also be set. In addition, the multicast hashing array must be set * to all 1's so that all multicast addresses are accepted. */ #define SE_RCR_PRO 0x10 /* * MON: Monitor Mode. If set, packets will be checked for good CRC and framing, * but are not stored in the ring-buffer. If clear, packets are stored (normal * operation). */ #define SE_RCR_MON 0x20 /* * bits 6 and 7 are unused/reserved. */ /* * Receiver Status Register (RSR) definitions */ /* * PRX: Packet Received without error. */ #define SE_RSR_PRX 0x01 /* * CRC: CRC error. Indicates that a packet has a CRC error. Also set for frame * alignment errors. */ #define SE_RSR_CRC 0x02 /* * FAE: Frame Alignment Error. Indicates that the incoming packet did not end on * a byte boundry and the CRC did not match at the last byte boundry. */ #define SE_RSR_FAE 0x04 /* * FO: FIFO Overrun. Indicates that the FIFO was not serviced (during local DMA) * causing it to overrun. Reception of the packet is aborted. */ #define SE_RSR_FO 0x08 /* * MPA: Missed Packet. Indicates that the received packet couldn't be stored in * the ring-buffer because of insufficient buffer space (exceeding the * boundry pointer), or because the transfer to the ring-buffer was inhibited * by RCR_MON - monitor mode. */ #define SE_RSR_MPA 0x10 /* * PHY: Physical address. If 0, the packet received was sent to a physical address. * If 1, the packet was accepted because of a multicast/broadcast address * match. */ #define SE_RSR_PHY 0x20 /* * DIS: Receiver Disabled. Set to indicate that the receiver has enetered monitor * mode. Cleared when the receiver exits monitor mode. */ #define SE_RSR_DIS 0x40 /* * DFR: Deferring. Set to indicate a 'jabber' condition. The CRS and COL inputs * are active, and the transceiver has set the CD line as a result of the * jabber. */ #define SE_RSR_DFR 0x80 /* * receive ring discriptor * * The National Semiconductor DS8390 Network interface controller uses * the following receive ring headers. The way this works is that the * memory on the interface card is chopped up into 256 bytes blocks. * A contiguous portion of those blocks are marked for receive packets * by setting start and end block #'s in the NIC. For each packet that * is put into the receive ring, one of these headers (4 bytes each) is * tacked onto the front. */ struct SE_ring { u_char rcv_status; /* received packet status */ u_char next_packet; /* pointer to next packet */ u_char count[2]; /* bytes in packet (length + 4) */ }; /* * Common constants */ #define SE_PAGE_SIZE 256 /* Size of RAM pages in bytes */ #define SE_TXBUF_SIZE 6 /* Size of TX buffer in pages */ /* * Vendor types */ #define SE_VENDOR_UNKNOWN 0xFF /* Unknown network card */ #define SE_VENDOR_APPLE 0x00 /* Apple Ethernet card */ #define SE_VENDOR_INTERLAN 0x01 /* Interlan A310 card (GatorCard) */ #define SE_VENDOR_DAYNA 0x02 /* DaynaPORT E/30s (and others?) */ /* * Compile-time config flags */ /* * this sets the default for enabling/disablng the tranceiver */ #define SE_FLAGS_DISABLE_TRANCEIVER 0x01 /* * This disables the use of double transmit buffers. */ #define SE_FLAGS_NO_DOUBLE_BUFFERING 0x08 /* */ #define GC_RESET_OFFSET 0x000c0000 /* writes here reset NIC */ #define GC_ROM_OFFSET 0x000c0000 /* address prom */ #define GC_DATA_OFFSET 0x000d0000 /* Offset to NIC memory */ #define GC_NIC_OFFSET 0x000e0000 /* Offset to NIC registers */ #define DP_ROM_OFFSET 0x000f0000 #define DP_DATA_OFFSET 0x000d0000 /* Offset to SONIC memory */ #define DP_NIC_OFFSET 0x000e0000 /* Offset to SONIC registers */ #define SE_ROM_OFFSET 0x000f0000 #define SE_DATA_OFFSET 0x000d0000 /* Offset to NIC memory */ #define SE_NIC_OFFSET 0x000e0000 /* Offset to NIC registers */