/* $NetBSD: i82596.c,v 1.17 2007/08/26 22:45:56 dyoung Exp $ */ /* * Copyright (c) 2003 Jochen Kunz. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of Jochen Kunz may not be used to endorse or promote * products derived from this software without specific prior * written permission. * * THIS SOFTWARE IS PROVIDED BY JOCHEN KUNZ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL JOCHEN KUNZ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * Driver for the Intel i82596CA and i82596DX/SX 10MBit/s Ethernet chips. * * It operates the i82596 in 32-Bit Linear Mode, opposed to the old i82586 * ie(4) driver (src/sys/dev/ic/i82586.c), that degrades the i82596 to * i82586 compatibility mode. * * Documentation about these chips can be found at * * http://developer.intel.com/design/network/datashts/290218.htm * http://developer.intel.com/design/network/datashts/290219.htm */ #include __KERNEL_RCSID(0, "$NetBSD: i82596.c,v 1.17 2007/08/26 22:45:56 dyoung Exp $"); /* autoconfig and device stuff */ #include #include #include #include "locators.h" #include "ioconf.h" /* bus_space / bus_dma etc. */ #include #include /* general system data and functions */ #include #include /* tsleep / sleep / wakeup */ #include /* hz for above */ #include /* network stuff */ #include #include #include #include #include #include #include "bpfilter.h" #if NBPFILTER > 0 #include #endif #include #include /* Supported chip variants */ const char *i82596_typenames[] = { "unknown", "DX/SX", "CA" }; /* media change and status callback */ static int iee_mediachange(struct ifnet *); static void iee_mediastatus(struct ifnet *, struct ifmediareq *); /* interface routines to upper protocols */ static void iee_start(struct ifnet *); /* initiate output */ static int iee_ioctl(struct ifnet *, u_long, void *); /* ioctl routine */ static int iee_init(struct ifnet *); /* init routine */ static void iee_stop(struct ifnet *, int); /* stop routine */ static void iee_watchdog(struct ifnet *); /* timer routine */ /* internal helper functions */ static void iee_cb_setup(struct iee_softc *, uint32_t); /* * Things a MD frontend has to provide: * * The functions via function pointers in the softc: * int (*sc_iee_cmd)(struct iee_softc *sc, uint32_t cmd); * int (*sc_iee_reset)(struct iee_softc *sc); * void (*sc_mediastatus)(struct ifnet *, struct ifmediareq *); * int (*sc_mediachange)(struct ifnet *); * * sc_iee_cmd(): send a command to the i82596 by writing the cmd parameter * to the SCP cmd word and issuing a Channel Attention. * sc_iee_reset(): initiate a reset, supply the address of the SCP to the * chip, wait for the chip to initialize and ACK interrupts that * this may have caused by calling (sc->sc_iee_cmd)(sc, IEE_SCB_ACK); * This functions must carefully bus_dmamap_sync() all data they have touched! * * sc_mediastatus() and sc_mediachange() are just MD hooks to the according * MI functions. The MD frontend may set this pointers to NULL when they * are not needed. * * sc->sc_type has to be set to I82596_UNKNOWN or I82596_DX or I82596_CA. * This is for printing out the correct chip type at attach time only. The * MI backend doesn't distinguish different chip types when programming * the chip. * * sc->sc_flags has to be set to 0 on little endian hardware and to * IEE_NEED_SWAP on big endian hardware, when endianess conversion is not * done by the bus attachment. Usually you need to set IEE_NEED_SWAP * when IEE_SYSBUS_BE is set in the sysbus byte. * * sc->sc_cl_align must be set to 1 or to the cache line size. When set to * 1 no special alignment of DMA descriptors is done. If sc->sc_cl_align != 1 * it forces alignment of the data structures in the shared memory to a multiple * of sc->sc_cl_align. This is needed on archs like hp700 that have non DMA * I/O coherent caches and are unable to map the shared memory uncachable. * (At least pre PA7100LC CPUs are unable to map memory uncachable.) * * sc->sc_cl_align MUST BE INITIALIZED BEFORE THE FOLLOWING MACROS ARE USED: * SC_* IEE_*_SZ IEE_*_OFF IEE_SHMEM_MAX (shell style glob(3) pattern) * * The MD frontend has to allocate a piece of DMA memory at least of * IEE_SHMEM_MAX bytes size. All communication with the chip is done via * this shared memory. If possible map this memory non-cachable on * archs with non DMA I/O coherent caches. The base of the memory needs * to be aligned to an even address if sc->sc_cl_align == 1 and aligned * to a cache line if sc->sc_cl_align != 1. * * An interrupt with iee_intr() as handler must be established. * * Call void iee_attach(struct iee_softc *sc, uint8_t *ether_address, * int *media, int nmedia, int defmedia); when everything is set up. First * parameter is a pointer to the MI softc, ether_address is an array that * contains the ethernet address. media is an array of the media types * provided by the hardware. The members of this array are supplied to * ifmedia_add() in sequence. nmedia is the count of elements in media. * defmedia is the default media that is set via ifmedia_set(). * nmedia and defmedia are ignored when media == NULL. * * The MD backend may call iee_detach() to detach the device. * * See sys/arch/hp700/gsc/if_iee_gsc.c for an example. */ /* * How frame reception is done: * Each Receive Frame Descriptor has one associated Receive Buffer Descriptor. * Each RBD points to the data area of an mbuf cluster. The RFDs are linked * together in a circular list. sc->sc_rx_done is the count of RFDs in the * list already processed / the number of the RFD that has to be checked for * a new frame first at the next RX interrupt. Upon successful reception of * a frame the mbuf cluster is handled to upper protocol layers, a new mbuf * cluster is allocated and the RFD / RBD are reinitialized accordingly. * * When a RFD list overrun occurred the whole RFD and RBD lists are reinitialized * and frame reception is started again. */ int iee_intr(void *intarg) { struct iee_softc *sc = intarg; struct ifnet *ifp = &sc->sc_ethercom.ec_if; struct iee_rfd *rfd; struct iee_rbd *rbd; bus_dmamap_t rx_map; struct mbuf *rx_mbuf; struct mbuf *new_mbuf; int scb_status; int scb_cmd; int n, col; if ((ifp->if_flags & IFF_RUNNING) == 0) { (sc->sc_iee_cmd)(sc, IEE_SCB_ACK); return(1); } bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, 0, IEE_SHMEM_MAX, BUS_DMASYNC_POSTREAD); scb_status = SC_SCB->scb_status; scb_cmd = SC_SCB->scb_cmd; rfd = SC_RFD(sc->sc_rx_done); while ((rfd->rfd_status & IEE_RFD_C) != 0) { /* At least one packet was received. */ rbd = SC_RBD(sc->sc_rx_done); rx_map = sc->sc_rx_map[sc->sc_rx_done]; rx_mbuf = sc->sc_rx_mbuf[sc->sc_rx_done]; SC_RBD((sc->sc_rx_done + IEE_NRFD - 1) % IEE_NRFD)->rbd_size &= ~IEE_RBD_EL; if ((rfd->rfd_status & IEE_RFD_OK) == 0 || (rbd->rbd_count & IEE_RBD_EOF) == 0 || (rbd->rbd_count & IEE_RBD_F) == 0){ /* Receive error, skip frame and reuse buffer. */ rfd->rfd_status = 0; rbd->rbd_count = 0; rbd->rbd_size = IEE_RBD_EL | rx_map->dm_segs[0].ds_len; printf("%s: iee_intr: receive error %d, rfd_status=" "0x%.4x, rfd_count=0x%.4x\n", sc->sc_dev.dv_xname, ++sc->sc_rx_err, rfd->rfd_status, rbd->rbd_count); sc->sc_rx_done = (sc->sc_rx_done + 1) % IEE_NRFD; continue; } rfd->rfd_status = 0; bus_dmamap_sync(sc->sc_dmat, rx_map, 0, rx_mbuf->m_ext.ext_size, BUS_DMASYNC_POSTREAD); rx_mbuf->m_pkthdr.len = rx_mbuf->m_len = rbd->rbd_count & IEE_RBD_COUNT; rx_mbuf->m_pkthdr.rcvif = ifp; MGETHDR(new_mbuf, M_DONTWAIT, MT_DATA); if (new_mbuf == NULL) { printf("%s: iee_intr: can't allocate mbuf\n", sc->sc_dev.dv_xname); break; } MCLAIM(new_mbuf, &sc->sc_ethercom.ec_rx_mowner); MCLGET(new_mbuf, M_DONTWAIT); if ((new_mbuf->m_flags & M_EXT) == 0) { printf("%s: iee_intr: can't alloc mbuf cluster\n", sc->sc_dev.dv_xname); m_freem(new_mbuf); break; } bus_dmamap_unload(sc->sc_dmat, rx_map); if (bus_dmamap_load(sc->sc_dmat, rx_map, new_mbuf->m_ext.ext_buf, new_mbuf->m_ext.ext_size, NULL, BUS_DMA_READ | BUS_DMA_NOWAIT) != 0) panic("%s: iee_intr: can't load RX DMA map\n", sc->sc_dev.dv_xname); bus_dmamap_sync(sc->sc_dmat, rx_map, 0, new_mbuf->m_ext.ext_size, BUS_DMASYNC_PREREAD); #if NBPFILTER > 0 if (ifp->if_bpf != 0) bpf_mtap(ifp->if_bpf, rx_mbuf); #endif /* NBPFILTER > 0 */ (*ifp->if_input)(ifp, rx_mbuf); ifp->if_ipackets++; sc->sc_rx_mbuf[sc->sc_rx_done] = new_mbuf; rbd->rbd_count = 0; rbd->rbd_size = IEE_RBD_EL | rx_map->dm_segs[0].ds_len; rbd->rbd_rb_addr = rx_map->dm_segs[0].ds_addr; sc->sc_rx_done = (sc->sc_rx_done + 1) % IEE_NRFD; rfd = SC_RFD(sc->sc_rx_done); } if ((scb_status & IEE_SCB_RUS) == IEE_SCB_RUS_NR1 || (scb_status & IEE_SCB_RUS) == IEE_SCB_RUS_NR2 || (scb_status & IEE_SCB_RUS) == IEE_SCB_RUS_NR3) { /* Receive Overrun, reinit receive ring buffer. */ for (n = 0 ; n < IEE_NRFD ; n++) { SC_RFD(n)->rfd_cmd = IEE_RFD_SF; SC_RFD(n)->rfd_link_addr = IEE_PHYS_SHMEM(IEE_RFD_OFF + IEE_RFD_SZ * ((n + 1) % IEE_NRFD)); SC_RBD(n)->rbd_next_rbd = IEE_PHYS_SHMEM(IEE_RBD_OFF + IEE_RBD_SZ * ((n + 1) % IEE_NRFD)); SC_RBD(n)->rbd_size = IEE_RBD_EL | sc->sc_rx_map[n]->dm_segs[0].ds_len; SC_RBD(n)->rbd_rb_addr = sc->sc_rx_map[n]->dm_segs[0].ds_addr; } SC_RFD(0)->rfd_rbd_addr = IEE_PHYS_SHMEM(IEE_RBD_OFF); sc->sc_rx_done = 0; bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, IEE_RFD_OFF, IEE_RFD_LIST_SZ + IEE_RBD_LIST_SZ, BUS_DMASYNC_PREWRITE); (sc->sc_iee_cmd)(sc, IEE_SCB_RUC_ST); printf("%s: iee_intr: receive ring buffer overrun\n", sc->sc_dev.dv_xname); } if (sc->sc_next_cb != 0 && (SC_CB(sc->sc_next_cb - 1)->cb_status & IEE_CB_C) != 0) { /* CMD list finished */ ifp->if_timer = 0; if (sc->sc_next_tbd != 0) { /* A TX CMD list finished, cleanup */ for (n = 0 ; n < sc->sc_next_cb ; n++) { m_freem(sc->sc_tx_mbuf[n]); sc->sc_tx_mbuf[n] = NULL; bus_dmamap_unload(sc->sc_dmat,sc->sc_tx_map[n]); if ((SC_CB(n)->cb_status & IEE_CB_COL) != 0 && (SC_CB(n)->cb_status & IEE_CB_MAXCOL) == 0) col = 16; else col = SC_CB(n)->cb_status & IEE_CB_MAXCOL; sc->sc_tx_col += col; if ((SC_CB(n)->cb_status & IEE_CB_OK) != 0) { ifp->if_opackets++; ifp->if_collisions += col; } } sc->sc_next_tbd = 0; ifp->if_flags &= ~IFF_OACTIVE; } for (n = 0 ; n < sc->sc_next_cb ; n++) { /* Check if a CMD failed, but ignore TX errors. */ if ((SC_CB(n)->cb_cmd & IEE_CB_CMD) != IEE_CB_CMD_TR && ((SC_CB(n)->cb_status & IEE_CB_OK) == 0)) printf("%s: iee_intr: scb_status=0x%x " "scb_cmd=0x%x failed command %d: " "cb_status[%d]=0x%.4x cb_cmd[%d]=0x%.4x\n", sc->sc_dev.dv_xname, scb_status, scb_cmd, ++sc->sc_cmd_err, n, SC_CB(n)->cb_status, n, SC_CB(n)->cb_cmd); } sc->sc_next_cb = 0; if ((sc->sc_flags & IEE_WANT_MCAST) != 0) { iee_cb_setup(sc, IEE_CB_CMD_MCS | IEE_CB_S | IEE_CB_EL | IEE_CB_I); (sc->sc_iee_cmd)(sc, IEE_SCB_CUC_EXE); } else /* Try to get deferred packets going. */ iee_start(ifp); } if (IEE_SWAP(SC_SCB->scb_crc_err) != sc->sc_crc_err) { sc->sc_crc_err = IEE_SWAP(SC_SCB->scb_crc_err); printf("%s: iee_intr: crc_err=%d\n", sc->sc_dev.dv_xname, sc->sc_crc_err); } if (IEE_SWAP(SC_SCB->scb_align_err) != sc->sc_align_err) { sc->sc_align_err = IEE_SWAP(SC_SCB->scb_align_err); printf("%s: iee_intr: align_err=%d\n", sc->sc_dev.dv_xname, sc->sc_align_err); } if (IEE_SWAP(SC_SCB->scb_resource_err) != sc->sc_resource_err) { sc->sc_resource_err = IEE_SWAP(SC_SCB->scb_resource_err); printf("%s: iee_intr: resource_err=%d\n", sc->sc_dev.dv_xname, sc->sc_resource_err); } if (IEE_SWAP(SC_SCB->scb_overrun_err) != sc->sc_overrun_err) { sc->sc_overrun_err = IEE_SWAP(SC_SCB->scb_overrun_err); printf("%s: iee_intr: overrun_err=%d\n", sc->sc_dev.dv_xname, sc->sc_overrun_err); } if (IEE_SWAP(SC_SCB->scb_rcvcdt_err) != sc->sc_rcvcdt_err) { sc->sc_rcvcdt_err = IEE_SWAP(SC_SCB->scb_rcvcdt_err); printf("%s: iee_intr: rcvcdt_err=%d\n", sc->sc_dev.dv_xname, sc->sc_rcvcdt_err); } if (IEE_SWAP(SC_SCB->scb_short_fr_err) != sc->sc_short_fr_err) { sc->sc_short_fr_err = IEE_SWAP(SC_SCB->scb_short_fr_err); printf("%s: iee_intr: short_fr_err=%d\n", sc->sc_dev.dv_xname, sc->sc_short_fr_err); } bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, 0, IEE_SHMEM_MAX, BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE); (sc->sc_iee_cmd)(sc, IEE_SCB_ACK); return(1); } /* * How Command Block List Processing is done. * * A running CBL is never manipulated. If there is a CBL already running, * further CMDs are deferred until the current list is done. A new list is * setup when the old one has finished. * This eases programming. To manipulate a running CBL it is necessary to * suspend the Command Unit to avoid race conditions. After a suspend * is sent we have to wait for an interrupt that ACKs the suspend. Then * we can manipulate the CBL and resume operation. I am not sure that this * is more effective then the current, much simpler approach. => KISS * See i82596CA data sheet page 26. * * A CBL is running or on the way to be set up when (sc->sc_next_cb != 0). * * A CBL may consist of TX CMDs, and _only_ TX CMDs. * A TX CBL is running or on the way to be set up when * ((sc->sc_next_cb != 0) && (sc->sc_next_tbd != 0)). * * A CBL may consist of other non-TX CMDs like IAS or CONF, and _only_ * non-TX CMDs. * * This comes mostly through the way how an Ethernet driver works and * because running CBLs are not manipulated when they are on the way. If * if_start() is called there will be TX CMDs enqueued so we have a running * CBL and other CMDs from e.g. if_ioctl() will be deferred and vice versa. * * The Multicast Setup Command is special. A MCS needs more space than * a single CB has. Actual space requirement depends on the length of the * multicast list. So we always defer MCS until other CBLs are finished, * then we setup a CONF CMD in the first CB. The CONF CMD is needed to * turn ALLMULTI on the hardware on or off. The MCS is the 2nd CB and may * use all the remaining space in the CBL and the Transmit Buffer Descriptor * List. (Therefore CBL and TBDL must be continuous in physical and virtual * memory. This is guaranteed through the definitions of the list offsets * in i82596reg.h and because it is only a single DMA segment used for all * lists.) When ALLMULTI is enabled via the CONF CMD, the MCS is run with * a multicast list length of 0, thus disabling the multicast filter. * A deferred MCS is signaled via ((sc->sc_flags & IEE_WANT_MCAST) != 0) */ void iee_cb_setup(struct iee_softc *sc, uint32_t cmd) { struct iee_cb *cb = SC_CB(sc->sc_next_cb); struct ifnet *ifp = &sc->sc_ethercom.ec_if; struct ether_multistep step; struct ether_multi *enm; memset(cb, 0, IEE_CB_SZ); cb->cb_cmd = cmd; switch(cmd & IEE_CB_CMD) { case IEE_CB_CMD_NOP: /* NOP CMD */ break; case IEE_CB_CMD_IAS: /* Individual Address Setup */ memcpy(__UNVOLATILE(cb->cb_ind_addr), CLLADDR(ifp->if_sadl), ETHER_ADDR_LEN); break; case IEE_CB_CMD_CONF: /* Configure */ memcpy(__UNVOLATILE(cb->cb_cf), sc->sc_cf, sc->sc_cf[0] & IEE_CF_0_CNT_M); break; case IEE_CB_CMD_MCS: /* Multicast Setup */ if (sc->sc_next_cb != 0) { sc->sc_flags |= IEE_WANT_MCAST; return; } sc->sc_flags &= ~IEE_WANT_MCAST; if ((sc->sc_cf[8] & IEE_CF_8_PRM) != 0) { /* Need no multicast filter in promisc mode. */ iee_cb_setup(sc, IEE_CB_CMD_CONF | IEE_CB_S | IEE_CB_EL | IEE_CB_I); return; } /* Leave room for a CONF CMD to en/dis-able ALLMULTI mode */ cb = SC_CB(sc->sc_next_cb + 1); cb->cb_cmd = cmd; cb->cb_mcast.mc_size = 0; ETHER_FIRST_MULTI(step, &sc->sc_ethercom, enm); while (enm != NULL) { if (memcmp(enm->enm_addrlo, enm->enm_addrhi, ETHER_ADDR_LEN) != 0 || cb->cb_mcast.mc_size * ETHER_ADDR_LEN + 2 * IEE_CB_SZ > IEE_CB_LIST_SZ + IEE_TBD_LIST_SZ) { cb->cb_mcast.mc_size = 0; break; } memcpy(__UNVOLATILE(&cb->cb_mcast.mc_addrs[ cb->cb_mcast.mc_size * ETHER_ADDR_LEN]), enm->enm_addrlo, ETHER_ADDR_LEN); ETHER_NEXT_MULTI(step, enm); cb->cb_mcast.mc_size++; } if (cb->cb_mcast.mc_size == 0) { /* Can't do exact mcast filtering, do ALLMULTI mode. */ ifp->if_flags |= IFF_ALLMULTI; sc->sc_cf[11] &= ~IEE_CF_11_MCALL; } else { /* disable ALLMULTI and load mcast list */ ifp->if_flags &= ~IFF_ALLMULTI; sc->sc_cf[11] |= IEE_CF_11_MCALL; /* Mcast setup may need more then IEE_CB_SZ bytes. */ bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, IEE_CB_OFF, IEE_CB_LIST_SZ + IEE_TBD_LIST_SZ, BUS_DMASYNC_PREWRITE); } iee_cb_setup(sc, IEE_CB_CMD_CONF); break; case IEE_CB_CMD_TR: /* Transmit */ cb->cb_transmit.tx_tbd_addr = IEE_PHYS_SHMEM(IEE_TBD_OFF + IEE_TBD_SZ * sc->sc_next_tbd); cb->cb_cmd |= IEE_CB_SF; /* Always use Flexible Mode. */ break; case IEE_CB_CMD_TDR: /* Time Domain Reflectometry */ break; case IEE_CB_CMD_DUMP: /* Dump */ break; case IEE_CB_CMD_DIAG: /* Diagnose */ break; default: /* can't happen */ break; } cb->cb_link_addr = IEE_PHYS_SHMEM(IEE_CB_OFF + IEE_CB_SZ * (sc->sc_next_cb + 1)); bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, IEE_CB_OFF + IEE_CB_SZ * sc->sc_next_cb, IEE_CB_SZ, BUS_DMASYNC_PREWRITE); sc->sc_next_cb++; ifp->if_timer = 5; return; } void iee_attach(struct iee_softc *sc, uint8_t *eth_addr, int *media, int nmedia, int defmedia) { struct ifnet *ifp = &sc->sc_ethercom.ec_if; int n; /* Set pointer to Intermediate System Configuration Pointer. */ /* Phys. addr. in big endian order. (Big endian as defined by Intel.) */ SC_SCP->scp_iscp_addr = IEE_SWAP(IEE_PHYS_SHMEM(IEE_ISCP_OFF)); /* Set pointer to System Control Block. */ /* Phys. addr. in big endian order. (Big endian as defined by Intel.) */ SC_ISCP->iscp_scb_addr = IEE_SWAP(IEE_PHYS_SHMEM(IEE_SCB_OFF)); /* Set pointer to Receive Frame Area. (physical address) */ SC_SCB->scb_rfa_addr = IEE_PHYS_SHMEM(IEE_RFD_OFF); /* Set pointer to Command Block. (physical address) */ SC_SCB->scb_cmd_blk_addr = IEE_PHYS_SHMEM(IEE_CB_OFF); ifmedia_init(&sc->sc_ifmedia, 0, iee_mediachange, iee_mediastatus); if (media != NULL) { for (n = 0 ; n < nmedia ; n++) ifmedia_add(&sc->sc_ifmedia, media[n], 0, NULL); ifmedia_set(&sc->sc_ifmedia, defmedia); } else { ifmedia_add(&sc->sc_ifmedia, IFM_ETHER | IFM_NONE, 0, NULL); ifmedia_set(&sc->sc_ifmedia, IFM_ETHER | IFM_NONE); } ifp->if_softc = sc; strcpy(ifp->if_xname, sc->sc_dev.dv_xname); ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_start = iee_start; /* initiate output routine */ ifp->if_ioctl = iee_ioctl; /* ioctl routine */ ifp->if_init = iee_init; /* init routine */ ifp->if_stop = iee_stop; /* stop routine */ ifp->if_watchdog = iee_watchdog; /* timer routine */ IFQ_SET_READY(&ifp->if_snd); /* iee supports IEEE 802.1Q Virtual LANs, see vlan(4). */ sc->sc_ethercom.ec_capabilities |= ETHERCAP_VLAN_MTU; if_attach(ifp); ether_ifattach(ifp, eth_addr); aprint_normal(": Intel 82596%s address %s\n", i82596_typenames[ sc->sc_type], ether_sprintf(eth_addr)); for (n = 0 ; n < IEE_NCB ; n++) sc->sc_tx_map[n] = NULL; for (n = 0 ; n < IEE_NRFD ; n++) { sc->sc_rx_mbuf[n] = NULL; sc->sc_rx_map[n] = NULL; } sc->sc_tx_timeout = 0; sc->sc_setup_timeout = 0; (sc->sc_iee_reset)(sc); return; } void iee_detach(struct iee_softc *sc, int flags) { struct ifnet *ifp = &sc->sc_ethercom.ec_if; if ((ifp->if_flags & IFF_RUNNING) != 0) iee_stop(ifp, 1); ether_ifdetach(ifp); if_detach(ifp); return; } /* media change and status callback */ int iee_mediachange(struct ifnet *ifp) { struct iee_softc *sc = ifp->if_softc; if (sc->sc_mediachange != NULL) return ((sc->sc_mediachange)(ifp)); return(0); } void iee_mediastatus(struct ifnet *ifp, struct ifmediareq *ifmreq) { struct iee_softc *sc = ifp->if_softc; if (sc->sc_mediastatus != NULL) return ((sc->sc_mediastatus)(ifp, ifmreq)); return; } /* initiate output routine */ void iee_start(struct ifnet *ifp) { struct iee_softc *sc = ifp->if_softc; struct mbuf *m = NULL; int t; int n; if (sc->sc_next_cb != 0) /* There is already a CMD running. Defer packet enqueuing. */ return; for (t = 0 ; t < IEE_NCB ; t++) { IFQ_DEQUEUE(&ifp->if_snd, sc->sc_tx_mbuf[t]); if (sc->sc_tx_mbuf[t] == NULL) break; if (bus_dmamap_load_mbuf(sc->sc_dmat, sc->sc_tx_map[t], sc->sc_tx_mbuf[t], BUS_DMA_WRITE | BUS_DMA_NOWAIT) != 0) { /* * The packet needs more TBD then we support. * Copy the packet into a mbuf cluster to get it out. */ printf("%s: iee_start: failed to load DMA map\n", sc->sc_dev.dv_xname); MGETHDR(m, M_DONTWAIT, MT_DATA); if (m == NULL) { printf("%s: iee_start: can't allocate mbuf\n", sc->sc_dev.dv_xname); m_freem(sc->sc_tx_mbuf[t]); t--; continue; } MCLAIM(m, &sc->sc_ethercom.ec_rx_mowner); MCLGET(m, M_DONTWAIT); if ((m->m_flags & M_EXT) == 0) { printf("%s: iee_start: can't allocate mbuf " "cluster\n", sc->sc_dev.dv_xname); m_freem(sc->sc_tx_mbuf[t]); m_freem(m); t--; continue; } m_copydata(sc->sc_tx_mbuf[t], 0, sc->sc_tx_mbuf[t]->m_pkthdr.len, mtod(m, void *)); m->m_pkthdr.len = sc->sc_tx_mbuf[t]->m_pkthdr.len; m->m_len = sc->sc_tx_mbuf[t]->m_pkthdr.len; m_freem(sc->sc_tx_mbuf[t]); sc->sc_tx_mbuf[t] = m; if(bus_dmamap_load_mbuf(sc->sc_dmat, sc->sc_tx_map[t], m, BUS_DMA_WRITE | BUS_DMA_NOWAIT) != 0) { printf("%s: iee_start: can't load TX DMA map\n", sc->sc_dev.dv_xname); m_freem(sc->sc_tx_mbuf[t]); t--; continue; } } for (n = 0 ; n < sc->sc_tx_map[t]->dm_nsegs ; n++) { SC_TBD(sc->sc_next_tbd + n)->tbd_tb_addr = sc->sc_tx_map[t]->dm_segs[n].ds_addr; SC_TBD(sc->sc_next_tbd + n)->tbd_size = sc->sc_tx_map[t]->dm_segs[n].ds_len; SC_TBD(sc->sc_next_tbd + n)->tbd_link_addr = IEE_PHYS_SHMEM(IEE_TBD_OFF + IEE_TBD_SZ * (sc->sc_next_tbd + n + 1)); } SC_TBD(sc->sc_next_tbd + n - 1)->tbd_size |= IEE_CB_EL; bus_dmamap_sync(sc->sc_dmat, sc->sc_tx_map[t], 0, sc->sc_tx_map[t]->dm_mapsize, BUS_DMASYNC_PREWRITE); IFQ_POLL(&ifp->if_snd, m); if (m == NULL) iee_cb_setup(sc, IEE_CB_CMD_TR | IEE_CB_S | IEE_CB_EL | IEE_CB_I); else iee_cb_setup(sc, IEE_CB_CMD_TR); sc->sc_next_tbd += n; #if NBPFILTER > 0 /* Pass packet to bpf if someone listens. */ if (ifp->if_bpf) bpf_mtap(ifp->if_bpf, sc->sc_tx_mbuf[t]); #endif } if (t == 0) /* No packets got set up for TX. */ return; if (t == IEE_NCB) ifp->if_flags |= IFF_OACTIVE; bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, IEE_CB_SZ, IEE_CB_LIST_SZ + IEE_TBD_LIST_SZ, BUS_DMASYNC_PREWRITE); (sc->sc_iee_cmd)(sc, IEE_SCB_CUC_EXE); return; } /* ioctl routine */ int iee_ioctl(struct ifnet *ifp, u_long cmd, void *data) { struct iee_softc *sc = ifp->if_softc; int s; int err; s = splnet(); switch (cmd) { case SIOCSIFMEDIA: case SIOCGIFMEDIA: err = ifmedia_ioctl(ifp, (struct ifreq *) data, &sc->sc_ifmedia, cmd); break; default: err = ether_ioctl(ifp, cmd, data); if (err == ENETRESET) { /* * Multicast list as changed; set the hardware filter * accordingly. */ if (ifp->if_flags & IFF_RUNNING) { iee_cb_setup(sc, IEE_CB_CMD_MCS | IEE_CB_S | IEE_CB_EL | IEE_CB_I); if ((sc->sc_flags & IEE_WANT_MCAST) == 0) (*sc->sc_iee_cmd)(sc, IEE_SCB_CUC_EXE); } err = 0; } break; } splx(s); return(err); } /* init routine */ int iee_init(struct ifnet *ifp) { struct iee_softc *sc = ifp->if_softc; int r; int t; int n; int err; sc->sc_next_cb = 0; sc->sc_next_tbd = 0; sc->sc_flags &= ~IEE_WANT_MCAST; sc->sc_rx_done = 0; SC_SCB->scb_crc_err = 0; SC_SCB->scb_align_err = 0; SC_SCB->scb_resource_err = 0; SC_SCB->scb_overrun_err = 0; SC_SCB->scb_rcvcdt_err = 0; SC_SCB->scb_short_fr_err = 0; sc->sc_crc_err = 0; sc->sc_align_err = 0; sc->sc_resource_err = 0; sc->sc_overrun_err = 0; sc->sc_rcvcdt_err = 0; sc->sc_short_fr_err = 0; sc->sc_tx_col = 0; sc->sc_rx_err = 0; sc->sc_cmd_err = 0; /* Create Transmit DMA maps. */ for (t = 0 ; t < IEE_NCB ; t++) { if (sc->sc_tx_map[t] == NULL && bus_dmamap_create(sc->sc_dmat, MCLBYTES, IEE_NTBD, MCLBYTES, 0, BUS_DMA_NOWAIT, &sc->sc_tx_map[t]) != 0) { printf("%s: iee_init: can't create TX DMA map\n", sc->sc_dev.dv_xname); for (n = 0 ; n < t ; n++) bus_dmamap_destroy(sc->sc_dmat, sc->sc_tx_map[n]); return(ENOBUFS); } } /* Initialize Receive Frame and Receive Buffer Descriptors */ err = 0; memset(SC_RFD(0), 0, IEE_RFD_LIST_SZ); memset(SC_RBD(0), 0, IEE_RBD_LIST_SZ); for (r = 0 ; r < IEE_NRFD ; r++) { SC_RFD(r)->rfd_cmd = IEE_RFD_SF; SC_RFD(r)->rfd_link_addr = IEE_PHYS_SHMEM(IEE_RFD_OFF + IEE_RFD_SZ * ((r + 1) % IEE_NRFD)); SC_RBD(r)->rbd_next_rbd = IEE_PHYS_SHMEM(IEE_RBD_OFF + IEE_RBD_SZ * ((r + 1) % IEE_NRFD)); if (sc->sc_rx_mbuf[r] == NULL) { MGETHDR(sc->sc_rx_mbuf[r], M_DONTWAIT, MT_DATA); if (sc->sc_rx_mbuf[r] == NULL) { printf("%s: iee_init: can't allocate mbuf\n", sc->sc_dev.dv_xname); err = 1; break; } MCLAIM(sc->sc_rx_mbuf[r],&sc->sc_ethercom.ec_rx_mowner); MCLGET(sc->sc_rx_mbuf[r], M_DONTWAIT); if ((sc->sc_rx_mbuf[r]->m_flags & M_EXT) == 0) { printf("%s: iee_init: can't allocate mbuf" " cluster\n", sc->sc_dev.dv_xname); m_freem(sc->sc_rx_mbuf[r]); err = 1; break; } } if (sc->sc_rx_map[r] == NULL && bus_dmamap_create(sc->sc_dmat, MCLBYTES, 1, MCLBYTES , 0, BUS_DMA_NOWAIT, &sc->sc_rx_map[r]) != 0) { printf("%s: iee_init: can't create RX " "DMA map\n", sc->sc_dev.dv_xname); m_freem(sc->sc_rx_mbuf[r]); err = 1; break; } if (bus_dmamap_load(sc->sc_dmat, sc->sc_rx_map[r], sc->sc_rx_mbuf[r]->m_ext.ext_buf, sc->sc_rx_mbuf[r]->m_ext.ext_size, NULL, BUS_DMA_READ | BUS_DMA_NOWAIT) != 0) { printf("%s: iee_init: can't load RX DMA map\n", sc->sc_dev.dv_xname); bus_dmamap_destroy(sc->sc_dmat, sc->sc_rx_map[r]); m_freem(sc->sc_rx_mbuf[r]); err = 1; break; } bus_dmamap_sync(sc->sc_dmat, sc->sc_rx_map[r], 0, sc->sc_rx_mbuf[r]->m_ext.ext_size, BUS_DMASYNC_PREREAD); SC_RBD(r)->rbd_size = sc->sc_rx_map[r]->dm_segs[0].ds_len; SC_RBD(r)->rbd_rb_addr= sc->sc_rx_map[r]->dm_segs[0].ds_addr; } SC_RFD(0)->rfd_rbd_addr = IEE_PHYS_SHMEM(IEE_RBD_OFF); if (err != 0) { for (n = 0 ; n < r; n++) { m_freem(sc->sc_rx_mbuf[n]); sc->sc_rx_mbuf[n] = NULL; bus_dmamap_unload(sc->sc_dmat, sc->sc_rx_map[n]); bus_dmamap_destroy(sc->sc_dmat, sc->sc_rx_map[n]); sc->sc_rx_map[n] = NULL; } for (n = 0 ; n < t ; n++) { bus_dmamap_destroy(sc->sc_dmat, sc->sc_tx_map[n]); sc->sc_tx_map[n] = NULL; } return(ENOBUFS); } (sc->sc_iee_reset)(sc); iee_cb_setup(sc, IEE_CB_CMD_IAS); sc->sc_cf[0] = IEE_CF_0_DEF | IEE_CF_0_PREF; sc->sc_cf[1] = IEE_CF_1_DEF; sc->sc_cf[2] = IEE_CF_2_DEF; sc->sc_cf[3] = IEE_CF_3_ADDRLEN_DEF | IEE_CF_3_NSAI | IEE_CF_3_PREAMLEN_DEF; sc->sc_cf[4] = IEE_CF_4_DEF; sc->sc_cf[5] = IEE_CF_5_DEF; sc->sc_cf[6] = IEE_CF_6_DEF; sc->sc_cf[7] = IEE_CF_7_DEF; sc->sc_cf[8] = IEE_CF_8_DEF; sc->sc_cf[9] = IEE_CF_9_DEF; sc->sc_cf[10] = IEE_CF_10_DEF; sc->sc_cf[11] = IEE_CF_11_DEF & ~IEE_CF_11_LNGFLD; sc->sc_cf[12] = IEE_CF_12_DEF; sc->sc_cf[13] = IEE_CF_13_DEF; iee_cb_setup(sc, IEE_CB_CMD_CONF | IEE_CB_S | IEE_CB_EL); SC_SCB->scb_rfa_addr = IEE_PHYS_SHMEM(IEE_RFD_OFF); bus_dmamap_sync(sc->sc_dmat, sc->sc_shmem_map, 0, IEE_SHMEM_MAX, BUS_DMASYNC_PREWRITE); (sc->sc_iee_cmd)(sc, IEE_SCB_CUC_EXE | IEE_SCB_RUC_ST); /* Issue a Channel Attention to ACK interrupts we may have caused. */ (sc->sc_iee_cmd)(sc, IEE_SCB_ACK); /* Mark the interface as running and ready to RX/TX packets. */ ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; return(0); } /* stop routine */ void iee_stop(struct ifnet *ifp, int disable) { struct iee_softc *sc = ifp->if_softc; int n; ifp->if_flags &= ~IFF_RUNNING; ifp->if_flags |= IFF_OACTIVE; ifp->if_timer = 0; /* Reset the chip to get it quiet. */ (sc->sc_iee_reset)(ifp->if_softc); /* Issue a Channel Attention to ACK interrupts we may have caused. */ (sc->sc_iee_cmd)(ifp->if_softc, IEE_SCB_ACK); /* Release any dynamically allocated resources. */ for (n = 0 ; n < IEE_NCB ; n++) { if (sc->sc_tx_map[n] != NULL) bus_dmamap_destroy(sc->sc_dmat, sc->sc_tx_map[n]); sc->sc_tx_map[n] = NULL; } for (n = 0 ; n < IEE_NRFD ; n++) { if (sc->sc_rx_mbuf[n] != NULL) m_freem(sc->sc_rx_mbuf[n]); sc->sc_rx_mbuf[n] = NULL; if (sc->sc_rx_map[n] != NULL) { bus_dmamap_unload(sc->sc_dmat, sc->sc_rx_map[n]); bus_dmamap_destroy(sc->sc_dmat, sc->sc_rx_map[n]); } sc->sc_rx_map[n] = NULL; } return; } /* timer routine */ void iee_watchdog(struct ifnet *ifp) { struct iee_softc *sc = ifp->if_softc; (sc->sc_iee_reset)(sc); if (sc->sc_next_tbd != 0) printf("%s: iee_watchdog: transmit timeout %d\n", sc->sc_dev.dv_xname, ++sc->sc_tx_timeout); else printf("%s: iee_watchdog: setup timeout %d\n", sc->sc_dev.dv_xname, ++sc->sc_setup_timeout); iee_init(ifp); return; }