/* * Device driver for National Semiconductor DS8390 based ethernet adapters. * * Based on original ISA bus driver by David Greenman, 29-April-1993 * * Copyright (C) 1993, David Greenman. This software may be used, modified, * copied, distributed, and sold, in both source and binary form provided * that the above copyright and these terms are retained. Under no * circumstances is the author responsible for the proper functioning * of this software, nor does the author assume any responsibility * for damages incurred with its use. * * Adapted for MacBSD by Brad Parker * * Currently supports: * Apples NB Ethernet card * Interlan A310 Nubus Ethernet card * Cayman Systems GatorCard */ /* * $Id: if_ae.c,v 1.12 1994/03/20 03:03:26 lkestel Exp $ */ #include "ae.h" /* bpfilter included here in case it is needed in future net includes */ #include "bpfilter.h" #include #include #include #include #include #include #include #include #include #include #include #ifdef INET #include #include #include #include #include #endif #ifdef NS #include #include #endif #if NBPFILTER > 0 #include #include #endif #include #include "nubus.h" #include "if_aereg.h" struct ae_device { struct device ae_dev; /* struct nubusdev ae_nu; struct intrhand ae_ih; */ }; /* * ae_softc: per line info and status */ struct ae_softc { struct ae_device *sc_ae; struct arpcom arpcom; /* ethernet common */ char *type_str; /* pointer to type string */ u_char vendor; /* interface vendor */ u_char type; /* interface type code */ #define APPLE_CARD(sc) ((sc)->vendor == AE_VENDOR_APPLE) #define REG_MAP(sc, reg) (APPLE_CARD(sc) ? (0x0f-(reg))<<2 : (reg)<<2) #define NIC_GET(sc, reg) ((sc)->nic_addr[REG_MAP(sc, reg)]) #define NIC_PUT(sc, reg, val) ((sc)->nic_addr[REG_MAP(sc, reg)] = (val)) volatile caddr_t nic_addr; /* NIC (DS8390) I/O bus address */ caddr_t rom_addr; /* on board prom address */ caddr_t smem_start; /* shared memory start address */ caddr_t smem_end; /* shared memory end address */ u_long smem_size; /* total shared memory size */ caddr_t smem_ring; /* start of RX ring-buffer (in smem) */ caddr_t bpf; /* BPF "magic cookie" */ u_char xmit_busy; /* transmitter is busy */ u_char txb_cnt; /* Number of transmit buffers */ u_char txb_next; /* Pointer to next buffer ready to xmit */ u_short txb_next_len; /* next xmit buffer length */ u_char data_buffered; /* data has been buffered in interface memory */ u_char tx_page_start; /* first page of TX buffer area */ u_char rec_page_start; /* first page of RX ring-buffer */ u_char rec_page_stop; /* last page of RX ring-buffer */ u_char next_packet; /* pointer to next unread RX packet */ } ae_softc[NAE]; void ae_find(), ae_attach(); int ae_init(), aeintr(), ae_ioctl(), ae_probe(), ae_start(), ae_reset(), ae_watchdog(); struct cfdriver aecd = { NULL, "ae", ae_probe, ae_attach, DV_IFNET, sizeof(struct ae_device), NULL, 0 }; static void ae_stop(); static inline void ae_rint(); static inline void ae_xmit(); static inline char *ae_ring_copy(); extern int ether_output(); #define ETHER_MIN_LEN 64 #define ETHER_MAX_LEN 1518 #define ETHER_ADDR_LEN 6 #define ETHER_HDR_SIZE 14 char ae_name[] = "8390 Nubus Ethernet card"; static char zero = 0; static u_char ones = 0xff; struct vendor_S { char *manu; int len; int vendor; } vend[] = { { "Apple", 5, AE_VENDOR_APPLE }, { "3Com", 4, AE_VENDOR_APPLE }, { "Dayna", 5, AE_VENDOR_DAYNA }, { "Inter", 5, AE_VENDOR_INTERLAN }, }; static int numvend = sizeof(vend)/sizeof(vend[0]); /* * XXX These two should be moved to locore, and maybe changed to use shorts * instead of bytes. The reason for these is that bcopy and bzero use longs, * which the ethernet cards can't handle. */ void bbzero (char *addr, int len) { while (len--) { *addr++ = 0; } } void bbcopy (char *src, char *dest, int len) { while (len--) { *dest++ = *src++; } } void ae_id_card(nu, sc) struct nubus_hw *nu; struct ae_softc *sc; { int i; /* * Try to determine what type of card this is... */ sc->vendor = AE_VENDOR_UNKNOWN; for (i=0 ; iSlot.manufacturer, vend[i].manu, vend[i].len)) { sc->vendor = vend[i].vendor; break; } } sc->type_str = (char *) (nu->Slot.manufacturer); /* see if it's an Interlan/GatorCard sc->rom_addr = nu->addr + GC_ROM_OFFSET; if (sc->rom_addr[0x18] == 0x0 && sc->rom_addr[0x1c] == 0x55) { sc->vendor = AE_VENDOR_INTERLAN; } */ } int ae_probe(parent, cf, aux) struct cfdriver *parent; struct cfdata *cf; void *aux; { register struct nubus_hw *nu = (struct nubus_hw *) aux; struct ae_softc *sc = &ae_softc[cf->cf_unit]; int i, memsize; int flags = 0; if (nu->Slot.type != NUBUS_NETWORK) return 0; ae_id_card(nu, sc); switch (sc->vendor) { case AE_VENDOR_INTERLAN: sc->nic_addr = nu->addr + GC_NIC_OFFSET; sc->rom_addr = nu->addr + GC_ROM_OFFSET; sc->smem_start = nu->addr + GC_DATA_OFFSET; memsize = 8192; /* reset the NIC chip */ *((caddr_t)nu->addr + GC_RESET_OFFSET) = (char)zero; /* Get station address from on-board ROM */ for (i = 0; i < ETHER_ADDR_LEN; ++i) sc->arpcom.ac_enaddr[i] = *(sc->rom_addr + i*4); break; case AE_VENDOR_APPLE: sc->nic_addr = nu->addr + AE_NIC_OFFSET; sc->rom_addr = nu->addr + AE_ROM_OFFSET; sc->smem_start = nu->addr + AE_DATA_OFFSET; memsize = 8192; /* Get station address from on-board ROM */ for (i = 0; i < ETHER_ADDR_LEN; ++i) sc->arpcom.ac_enaddr[i] = *(sc->rom_addr + i*2); break; case AE_VENDOR_DAYNA: printf("We think we are a Dayna card, but "); sc->nic_addr = nu->addr + DP_NIC_OFFSET; sc->rom_addr = nu->addr + DP_ROM_OFFSET; sc->smem_start = nu->addr + DP_DATA_OFFSET; memsize = 8192; /* Get station address from on-board ROM */ for (i = 0; i < ETHER_ADDR_LEN; ++i) sc->arpcom.ac_enaddr[i] = *(sc->rom_addr + i*2); printf("it is dangerous to continue.\n"); return 0; /* Since we don't work yet... */ break; default: return 0; break; } /* * allocate one xmit buffer if < 16k, two buffers otherwise */ if ((memsize < 16384) || (flags & AE_FLAGS_NO_DOUBLE_BUFFERING)) { sc->smem_ring = sc->smem_start + (AE_PAGE_SIZE * AE_TXBUF_SIZE); sc->txb_cnt = 1; sc->rec_page_start = AE_TXBUF_SIZE; } else { sc->smem_ring = sc->smem_start + (AE_PAGE_SIZE * AE_TXBUF_SIZE * 2); sc->txb_cnt = 2; sc->rec_page_start = AE_TXBUF_SIZE * 2; } sc->smem_size = memsize; sc->smem_end = sc->smem_start + memsize; sc->rec_page_stop = memsize / AE_PAGE_SIZE; sc->tx_page_start = 0; /* * Now zero memory and verify that it is clear */ bbzero(sc->smem_start, memsize); for (i = 0; i < memsize; ++i) if (sc->smem_start[i]) { printf(": failed to clear shared memory at %x\n", sc->smem_start + i); return(0); } #ifdef DEBUG_PRINT printf("nic_addr %x, rom_addr %x\n", sc->nic_addr, sc->rom_addr); printf("smem_size %d\n", sc->smem_size); printf("smem_start %x, smem_ring %x, smem_end %x\n", sc->smem_start, sc->smem_ring, sc->smem_end); printf("phys address %02x:%02x:%02x:%02x:%02x:%02x\n", sc->arpcom.ac_enaddr[0], sc->arpcom.ac_enaddr[1], sc->arpcom.ac_enaddr[2], sc->arpcom.ac_enaddr[3], sc->arpcom.ac_enaddr[4], sc->arpcom.ac_enaddr[5]); #endif return(1); } /* * Install interface into kernel networking data structures */ void ae_attach(parent, self, aux) struct cfdriver *parent, *self; void *aux; { struct nubus_hw *nu = aux; struct ae_device *ae = (struct ae_device *) self; struct ae_softc *sc = &ae_softc[ae->ae_dev.dv_unit]; struct cfdata *cf = ae->ae_dev.dv_cfdata; struct ifnet *ifp = &sc->arpcom.ac_if; struct ifaddr *ifa; struct sockaddr_dl *sdl; sc->sc_ae = ae; /* * Set interface to stopped condition (reset) */ ae_stop(sc); /* * Initialize ifnet structure */ ifp->if_unit = ae->ae_dev.dv_unit; ifp->if_name = aecd.cd_name; ifp->if_mtu = ETHERMTU; ifp->if_output = ether_output; ifp->if_start = ae_start; ifp->if_ioctl = ae_ioctl; ifp->if_reset = ae_reset; ifp->if_watchdog = ae_watchdog; ifp->if_flags = (IFF_BROADCAST | IFF_SIMPLEX | IFF_NOTRAILERS); #if 0 /* * Set default state for ALTPHYS flag (used to disable the transceiver * for AUI operation), based on compile-time config option. */ if (cf->cf_flags & AE_FLAGS_DISABLE_TRANSCEIVER) ifp->if_flags |= IFF_ALTPHYS; #endif /* * Attach the interface */ if_attach(ifp); /* * Search down the ifa address list looking for the AF_LINK type entry */ ifa = ifp->if_addrlist; while ((ifa != 0) && (ifa->ifa_addr != 0) && (ifa->ifa_addr->sa_family != AF_LINK)) ifa = ifa->ifa_next; /* * If we find an AF_LINK type entry we fill in the hardware address. * This is useful for netstat(1) to keep track of which interface * is which. */ if ((ifa != 0) && (ifa->ifa_addr != 0)) { /* * Fill in the link-level address for this interface */ sdl = (struct sockaddr_dl *)ifa->ifa_addr; sdl->sdl_type = IFT_ETHER; sdl->sdl_alen = ETHER_ADDR_LEN; sdl->sdl_slen = 0; bbcopy(sc->arpcom.ac_enaddr, LLADDR(sdl), ETHER_ADDR_LEN); } /* * Print additional info when attached */ printf(": address %s, ", ether_sprintf(sc->arpcom.ac_enaddr)); if (sc->type_str && (*sc->type_str != 0)) printf("type %s ", sc->type_str); else printf("type unknown (0x%x) ", sc->type); printf("\n"); /* * If BPF is in the kernel, call the attach for it */ #if NBPFILTER > 0 bpfattach(&sc->bpf, ifp, DLT_EN10MB, sizeof(struct ether_header)); #endif } /* * Reset interface. */ int ae_reset(sc) struct ae_softc *sc; { int s; s = splnet(); /* * Stop interface and re-initialize. */ ae_stop(sc); ae_init(sc); (void) splx(s); } /* * Take interface offline. */ void ae_stop(sc) struct ae_softc *sc; { int n = 5000; /* * Stop everything on the interface, and select page 0 registers. */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_STP); /* * Wait for interface to enter stopped state, but limit # of checks * to 'n' (about 5ms). It shouldn't even take 5us on modern * DS8390's, but just in case it's an old one. */ while (((NIC_GET(sc, AE_P0_ISR) & AE_ISR_RST) == 0) && --n); } /* * Device timeout/watchdog routine. Entered if the device neglects to * generate an interrupt after a transmit has been started on it. */ int ae_watchdog(unit) short unit; { log(LOG_ERR, "ae%d: device timeout\n", unit); { struct ae_softc *sc = &ae_softc[unit]; printf("cr %x, isr %x\n", NIC_GET(sc, AE_P0_CR), NIC_GET(sc, AE_P0_ISR)); /* via_dump(); */ if (NIC_GET(sc, AE_P0_ISR)) { aeintr(0); return; } } ae_reset(unit); } /* * Initialize device. */ ae_init(sc) struct ae_softc *sc; { struct ifnet *ifp = &sc->arpcom.ac_if; int i, s; u_char command; /* address not known */ if (ifp->if_addrlist == (struct ifaddr *)0) return; /* * Initialize the NIC in the exact order outlined in the NS manual. * This init procedure is "mandatory"...don't change what or when * things happen. */ s = splnet(); /* reset transmitter flags */ sc->data_buffered = 0; sc->xmit_busy = 0; sc->arpcom.ac_if.if_timer = 0; sc->txb_next = 0; /* This variable is used below - don't move this assignment */ sc->next_packet = sc->rec_page_start + 1; #ifdef DEBUG_PRINT printf("page_start %d, page_stop %d, next %d\n", sc->rec_page_start, sc->rec_page_stop, sc->next_packet); #endif /* * Set interface for page 0, Remote DMA complete, Stopped */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_STP); /* * Set FIFO threshold to 4, No auto-init Remote DMA, Burst mode, * byte order=80x86, word-wide DMA xfers, */ NIC_PUT(sc, AE_P0_DCR, AE_DCR_FT1|AE_DCR_BMS|AE_DCR_WTS); /* * Clear Remote Byte Count Registers */ NIC_PUT(sc, AE_P0_RBCR0, zero); NIC_PUT(sc, AE_P0_RBCR1, zero); /* * Enable reception of broadcast packets */ NIC_PUT(sc, AE_P0_RCR, AE_RCR_AB); /* * Place NIC in internal loopback mode */ NIC_PUT(sc, AE_P0_TCR, AE_TCR_LB0); /* * Initialize transmit/receive (ring-buffer) Page Start */ NIC_PUT(sc, AE_P0_TPSR, sc->tx_page_start); NIC_PUT(sc, AE_P0_PSTART, sc->rec_page_start); /* * Initialize Receiver (ring-buffer) Page Stop and Boundry */ NIC_PUT(sc, AE_P0_PSTOP, sc->rec_page_stop); NIC_PUT(sc, AE_P0_BNRY, sc->rec_page_start); /* * Clear all interrupts. A '1' in each bit position clears the * corresponding flag. */ NIC_PUT(sc, AE_P0_ISR, ones); /* * Enable the following interrupts: receive/transmit complete, * receive/transmit error, and Receiver OverWrite. * * Counter overflow and Remote DMA complete are *not* enabled. */ NIC_PUT(sc, AE_P0_IMR, AE_IMR_PRXE|AE_IMR_PTXE|AE_IMR_RXEE|AE_IMR_TXEE|AE_IMR_OVWE); /* * Program Command Register for page 1 */ NIC_PUT(sc, AE_P0_CR, AE_CR_PAGE_1|AE_CR_RD2|AE_CR_STP); /* * Copy out our station address */ for (i = 0; i < ETHER_ADDR_LEN; ++i) NIC_PUT(sc, AE_P1_PAR0 + i, sc->arpcom.ac_enaddr[i]); #if NBPFILTER > 0 /* * Initialize multicast address hashing registers to accept * all multicasts (only used when in promiscuous mode) */ for (i = 0; i < 8; ++i) NIC_PUT(sc, AE_P1_MAR0 + i, 0xff); #endif /* * Set Current Page pointer to next_packet (initialized above) */ NIC_PUT(sc, AE_P1_CURR, sc->next_packet); /* * Set Command Register for page 0, Remote DMA complete, * and interface Start. */ NIC_PUT(sc, AE_P1_CR, AE_CR_RD2|AE_CR_STA); /* * Take interface out of loopback */ NIC_PUT(sc, AE_P0_TCR, zero); /* * Set 'running' flag, and clear output active flag. */ ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; /* XXXXXX */ add_nubus_intr((int)sc->rom_addr & 0xFF000000, aeintr, sc - ae_softc); /* * ...and attempt to start output */ ae_start(ifp); (void) splx(s); } /* * This routine actually starts the transmission on the interface */ static inline void ae_xmit(ifp) struct ifnet *ifp; { struct ae_softc *sc = &ae_softc[ifp->if_unit]; u_short len = sc->txb_next_len; /* * Set NIC for page 0 register access */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_STA); /* * Set TX buffer start page */ NIC_PUT(sc, AE_P0_TPSR, sc->tx_page_start + sc->txb_next * AE_TXBUF_SIZE); /* * Set TX length */ NIC_PUT(sc, AE_P0_TBCR0, len & 0xff); NIC_PUT(sc, AE_P0_TBCR1, len >> 8); /* * Set page 0, Remote DMA complete, Transmit Packet, and *Start* */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_TXP|AE_CR_STA); sc->xmit_busy = 1; sc->data_buffered = 0; /* * Switch buffers if we are doing double-buffered transmits */ if ((sc->txb_next == 0) && (sc->txb_cnt > 1)) sc->txb_next = 1; else sc->txb_next = 0; /* * Set a timer just in case we never hear from the board again */ ifp->if_timer = 2; } /* * Start output on interface. * We make two assumptions here: * 1) that the current priority is set to splnet _before_ this code * is called *and* is returned to the appropriate priority after * return * 2) that the IFF_OACTIVE flag is checked before this code is called * (i.e. that the output part of the interface is idle) */ int ae_start(ifp) struct ifnet *ifp; { struct ae_softc *sc = &ae_softc[ifp->if_unit]; struct mbuf *m0, *m; caddr_t buffer; int len; outloop: /* * See if there is room to send more data (i.e. one or both of the * buffers is empty). */ if (sc->data_buffered) if (sc->xmit_busy) { /* * No room. Indicate this to the outside world * and exit. */ ifp->if_flags |= IFF_OACTIVE; return; } else { /* * Data is buffered, but we're not transmitting, so * start the xmit on the buffered data. * Note that ae_xmit() resets the data_buffered flag * before returning. */ ae_xmit(ifp); } IF_DEQUEUE(&sc->arpcom.ac_if.if_snd, m); if (m == 0) { /* * The following isn't pretty; we are using the !OACTIVE flag to * indicate to the outside world that we can accept an additional * packet rather than that the transmitter is _actually_ * active. Indeed, the transmitter may be active, but if we haven't * filled the secondary buffer with data then we still want to * accept more. * Note that it isn't necessary to test the data_buffered flag - * we wouldn't have tried to de-queue the packet in the first place * if it was set. */ ifp->if_flags &= ~IFF_OACTIVE; return; } /* * Copy the mbuf chain into the transmit buffer */ buffer = sc->smem_start + (sc->txb_next * AE_TXBUF_SIZE * AE_PAGE_SIZE); len = 0; for (m0 = m; m != 0; m = m->m_next) { /*printf("ae: copy %d bytes @ %x\n", m->m_len, buffer);*/ bbcopy(mtod(m, caddr_t), buffer, m->m_len); buffer += m->m_len; len += m->m_len; } if (len & 1) len++; sc->txb_next_len = MAX(len, ETHER_MIN_LEN); if (sc->txb_cnt > 1) /* * only set 'buffered' flag if doing multiple buffers */ sc->data_buffered = 1; if (sc->xmit_busy == 0) ae_xmit(ifp); /* * If there is BPF support in the configuration, tap off here. * The following has support for converting trailer packets * back to normal. */ #if NBPFILTER > 0 if (sc->bpf) { u_short etype; int off, datasize, resid; struct ether_header *eh; struct trailer_header { u_short ether_type; u_short ether_residual; } trailer_header; char ether_packet[ETHER_MAX_LEN]; char *ep; ep = ether_packet; /* * We handle trailers below: * Copy ether header first, then residual data, * then data. Put all this in a temporary buffer * 'ether_packet' and send off to bpf. Since the * system has generated this packet, we assume * that all of the offsets in the packet are * correct; if they're not, the system will almost * certainly crash in m_copydata. * We make no assumptions about how the data is * arranged in the mbuf chain (i.e. how much * data is in each mbuf, if mbuf clusters are * used, etc.), which is why we use m_copydata * to get the ether header rather than assume * that this is located in the first mbuf. */ /* copy ether header */ m_copydata(m0, 0, sizeof(struct ether_header), ep); eh = (struct ether_header *) ep; ep += sizeof(struct ether_header); etype = ntohs(eh->ether_type); if (etype >= ETHERTYPE_TRAIL && etype < ETHERTYPE_TRAIL+ETHERTYPE_NTRAILER) { datasize = ((etype - ETHERTYPE_TRAIL) << 9); off = datasize + sizeof(struct ether_header); /* copy trailer_header into a data structure */ m_copydata(m0, off, sizeof(struct trailer_header), &trailer_header.ether_type); /* copy residual data */ m_copydata(m0, off+sizeof(struct trailer_header), resid = ntohs(trailer_header.ether_residual) - sizeof(struct trailer_header), ep); ep += resid; /* copy data */ m_copydata(m0, sizeof(struct ether_header), datasize, ep); ep += datasize; /* restore original ether packet type */ eh->ether_type = trailer_header.ether_type; bpf_tap(sc->bpf, ether_packet, ep - ether_packet); } else bpf_mtap(sc->bpf, m0); } #endif m_freem(m0); /* * If we are doing double-buffering, a buffer might be free to * fill with another packet, so loop back to the top. */ if (sc->txb_cnt > 1) goto outloop; else { ifp->if_flags |= IFF_OACTIVE; return; } } /* * Ethernet interface receiver interrupt. */ static inline void ae_rint(unit) int unit; { register struct ae_softc *sc = &ae_softc[unit]; u_char boundry, current; u_short len; struct ae_ring *packet_ptr; /* * Set NIC to page 1 registers to get 'current' pointer */ NIC_PUT(sc, AE_P0_CR, AE_CR_PAGE_1|AE_CR_RD2|AE_CR_STA); /* * 'sc->next_packet' is the logical beginning of the ring-buffer - i.e. * it points to where new data has been buffered. The 'CURR' * (current) register points to the logical end of the ring-buffer * - i.e. it points to where additional new data will be added. * We loop here until the logical beginning equals the logical * end (or in other words, until the ring-buffer is empty). */ while (sc->next_packet != NIC_GET(sc, AE_P1_CURR)) { /* get pointer to this buffer header structure */ packet_ptr = (struct ae_ring *)(sc->smem_ring + (sc->next_packet - sc->rec_page_start) * AE_PAGE_SIZE); /* * The byte count includes the FCS - Frame Check Sequence (a * 32 bit CRC). */ len = packet_ptr->count[0] | (packet_ptr->count[1] << 8); if ((len >= ETHER_MIN_LEN) && (len <= ETHER_MAX_LEN)) { /* * Go get packet. len - 4 removes CRC from length. * (packet_ptr + 1) points to data just after the packet ring * header (+4 bytes) */ ae_get_packet(sc, (caddr_t)(packet_ptr + 1), len - 4); ++sc->arpcom.ac_if.if_ipackets; } else { /* * Really BAD...probably indicates that the ring pointers * are corrupted. Also seen on early rev chips under * high load - the byte order of the length gets switched. */ log(LOG_ERR, "ae%d: shared memory corrupt - invalid packet length %d\n", unit, len); ae_reset(unit); return; } /* * Update next packet pointer */ sc->next_packet = packet_ptr->next_packet; /* * Update NIC boundry pointer - being careful to keep it * one buffer behind. (as recommended by NS databook) */ boundry = sc->next_packet - 1; if (boundry < sc->rec_page_start) boundry = sc->rec_page_stop - 1; /* * Set NIC to page 0 registers to update boundry register */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_STA); NIC_PUT(sc, AE_P0_BNRY, boundry); /* * Set NIC to page 1 registers before looping to top (prepare to * get 'CURR' current pointer) */ NIC_PUT(sc, AE_P0_CR, AE_CR_PAGE_1|AE_CR_RD2|AE_CR_STA); } } /* * Ethernet interface interrupt processor */ int aeintr(unit) int unit; { struct ae_softc *sc = &ae_softc[unit]; u_char isr; /* * Set NIC to page 0 registers */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_STA); /* * loop until there are no more new interrupts */ while (isr = NIC_GET(sc, AE_P0_ISR)) { /* * reset all the bits that we are 'acknowledging' * by writing a '1' to each bit position that was set * (writing a '1' *clears* the bit) */ NIC_PUT(sc, AE_P0_ISR, isr); /* * Handle transmitter interrupts. Handle these first * because the receiver will reset the board under * some conditions. */ if (isr & (AE_ISR_PTX|AE_ISR_TXE)) { u_char collisions = NIC_GET(sc, AE_P0_NCR); /* * Check for transmit error. If a TX completed with an * error, we end up throwing the packet away. Really * the only error that is possible is excessive * collisions, and in this case it is best to allow the * automatic mechanisms of TCP to backoff the flow. Of * course, with UDP we're screwed, but this is expected * when a network is heavily loaded. */ if (isr & AE_ISR_TXE) { /* * Excessive collisions (16) */ if ((NIC_GET(sc, AE_P0_TSR) & AE_TSR_ABT) && (collisions == 0)) { /* * When collisions total 16, the * P0_NCR will indicate 0, and the * TSR_ABT is set. */ collisions = 16; } /* * update output errors counter */ ++sc->arpcom.ac_if.if_oerrors; } else { /* * Update total number of successfully * transmitted packets. */ ++sc->arpcom.ac_if.if_opackets; } /* * reset tx busy and output active flags */ sc->xmit_busy = 0; sc->arpcom.ac_if.if_flags &= ~IFF_OACTIVE; /* * clear watchdog timer */ sc->arpcom.ac_if.if_timer = 0; /* * Add in total number of collisions on last * transmission. */ sc->arpcom.ac_if.if_collisions += collisions; /* * If data is ready to transmit, start it transmitting, * otherwise defer until after handling receiver */ if (sc->data_buffered) ae_xmit(&sc->arpcom.ac_if); } /* * Handle receiver interrupts */ if (isr & (AE_ISR_PRX|AE_ISR_RXE|AE_ISR_OVW)) { /* * Overwrite warning. In order to make sure that a lockup * of the local DMA hasn't occurred, we reset and * re-init the NIC. The NSC manual suggests only a * partial reset/re-init is necessary - but some * chips seem to want more. The DMA lockup has been * seen only with early rev chips - Methinks this * bug was fixed in later revs. -DG */ if (isr & AE_ISR_OVW) { ++sc->arpcom.ac_if.if_ierrors; log(LOG_WARNING, "ae%d: warning - receiver ring buffer overrun\n", unit); /* * Stop/reset/re-init NIC */ ae_reset(unit); } else { /* * Receiver Error. One or more of: CRC error, frame * alignment error FIFO overrun, or missed packet. */ if (isr & AE_ISR_RXE) { ++sc->arpcom.ac_if.if_ierrors; #ifdef AE_DEBUG printf("ae%d: receive error %x\n", unit, NIC_GET(sc, AE_P0_RSR)); #endif } /* * Go get the packet(s) * XXX - Doing this on an error is dubious * because there shouldn't be any data to * get (we've configured the interface to * not accept packets with errors). */ ae_rint (unit); } } /* * If it looks like the transmitter can take more data, * attempt to start output on the interface. * This is done after handling the receiver to * give the receiver priority. */ if ((sc->arpcom.ac_if.if_flags & IFF_OACTIVE) == 0) ae_start(&sc->arpcom.ac_if); /* * return NIC CR to standard state: page 0, remote DMA complete, * start (toggling the TXP bit off, even if was just set * in the transmit routine, is *okay* - it is 'edge' * triggered from low to high) */ NIC_PUT(sc, AE_P0_CR, AE_CR_RD2|AE_CR_STA); /* * If the Network Talley Counters overflow, read them to * reset them. It appears that old 8390's won't * clear the ISR flag otherwise - resulting in an * infinite loop. */ if (isr & AE_ISR_CNT) { (void) NIC_GET(sc, AE_P0_CNTR0); (void) NIC_GET(sc, AE_P0_CNTR1); (void) NIC_GET(sc, AE_P0_CNTR2); } } } /* * Process an ioctl request. This code needs some work - it looks * pretty ugly. */ int ae_ioctl(ifp, command, data) register struct ifnet *ifp; int command; caddr_t data; { register struct ifaddr *ifa = (struct ifaddr *)data; struct ae_softc *sc = &ae_softc[ifp->if_unit]; struct ifreq *ifr = (struct ifreq *)data; int s, error = 0; s = splnet(); switch (command) { case SIOCSIFADDR: ifp->if_flags |= IFF_UP; switch (ifa->ifa_addr->sa_family) { #ifdef INET case AF_INET: ae_init(sc); /* before arpwhohas */ /* * See if another station has *our* IP address. * i.e.: There is an address conflict! If a * conflict exists, a message is sent to the * console. */ ((struct arpcom *)ifp)->ac_ipaddr = IA_SIN(ifa)->sin_addr; arpwhohas((struct arpcom *)ifp, &IA_SIN(ifa)->sin_addr); break; #endif #ifdef NS /* * XXX - This code is probably wrong */ case AF_NS: { register struct ns_addr *ina = &(IA_SNS(ifa)->sns_addr); if (ns_nullhost(*ina)) ina->x_host = *(union ns_host *)(sc->arpcom.ac_enaddr); else { /* * */ bbcopy((caddr_t)ina->x_host.c_host, (caddr_t)sc->arpcom.ac_enaddr, sizeof(sc->arpcom.ac_enaddr)); } /* * Set new address */ ae_init(sc); break; } #endif default: ae_init(sc); break; } break; case SIOCSIFFLAGS: /* * If interface is marked down and it is running, then stop it */ if (((ifp->if_flags & IFF_UP) == 0) && (ifp->if_flags & IFF_RUNNING)) { ae_stop(ifp->if_unit); ifp->if_flags &= ~IFF_RUNNING; } else { /* * If interface is marked up and it is stopped, then start it */ if ((ifp->if_flags & IFF_UP) && ((ifp->if_flags & IFF_RUNNING) == 0)) ae_init(sc); } #if NBPFILTER > 0 if (ifp->if_flags & IFF_PROMISC) { /* * Set promiscuous mode on interface. * XXX - for multicasts to work, we would need to * write 1's in all bits of multicast * hashing array. For now we assume that * this was done in ae_init(). */ NIC_PUT(sc, AE_P0_RCR, AE_RCR_PRO|AE_RCR_AM|AE_RCR_AB); } else { /* * XXX - for multicasts to work, we would need to * rewrite the multicast hashing array with the * proper hash (would have been destroyed above). */ NIC_PUT(sc, AE_P0_RCR, AE_RCR_AB); } #endif break; default: error = EINVAL; } (void) splx(s); return (error); } /* * Macro to calculate a new address within shared memory when given an offset * from an address, taking into account ring-wrap. */ #define ringoffset(sc, start, off, type) \ ((type)( ((caddr_t)(start)+(off) >= (sc)->smem_end) ? \ (((caddr_t)(start)+(off))) - (sc)->smem_end \ + (sc)->smem_ring: \ ((caddr_t)(start)+(off)) )) /* * Retreive packet from shared memory and send to the next level up via * ether_input(). If there is a BPF listener, give a copy to BPF, too. */ ae_get_packet(sc, buf, len) struct ae_softc *sc; char *buf; u_short len; { struct ether_header *eh; struct mbuf *m, *head, *ae_ring_to_mbuf(); u_short off; int resid; u_short etype; struct trailer_header { u_short trail_type; u_short trail_residual; } trailer_header; /* Allocate a header mbuf */ MGETHDR(m, M_DONTWAIT, MT_DATA); if (m == 0) goto bad; m->m_pkthdr.rcvif = &sc->arpcom.ac_if; m->m_pkthdr.len = len; m->m_len = 0; head = m; eh = (struct ether_header *)buf; /* The following sillines is to make NFS happy */ #define EROUND ((sizeof(struct ether_header) + 3) & ~3) #define EOFF (EROUND - sizeof(struct ether_header)) /* * The following assumes there is room for * the ether header in the header mbuf */ head->m_data += EOFF; bbcopy(buf, mtod(head, caddr_t), sizeof(struct ether_header)); buf += sizeof(struct ether_header); head->m_len += sizeof(struct ether_header); len -= sizeof(struct ether_header); etype = ntohs((u_short)eh->ether_type); /* * Deal with trailer protocol: * If trailer protocol, calculate the datasize as 'off', * which is also the offset to the trailer header. * Set resid to the amount of packet data following the * trailer header. * Finally, copy residual data into mbuf chain. */ if (etype >= ETHERTYPE_TRAIL && etype < ETHERTYPE_TRAIL+ETHERTYPE_NTRAILER) { off = (etype - ETHERTYPE_TRAIL) << 9; if ((off + sizeof(struct trailer_header)) > len) goto bad; /* insanity */ eh->ether_type = *ringoffset(sc, buf, off, u_short *); resid = ntohs(*ringoffset(sc, buf, off+2, u_short *)); if ((off + resid) > len) goto bad; /* insanity */ resid -= sizeof(struct trailer_header); if (resid < 0) goto bad; /* insanity */ m = ae_ring_to_mbuf(sc, ringoffset(sc, buf, off+4, char *), head, resid); if (m == 0) goto bad; len = off; head->m_pkthdr.len -= 4; /* subtract trailer header */ } /* * Pull packet off interface. Or if this was a trailer packet, * the data portion is appended. */ m = ae_ring_to_mbuf(sc, buf, m, len); if (m == 0) goto bad; #if NBPFILTER > 0 /* * Check if there's a BPF listener on this interface. * If so, hand off the raw packet to bpf. */ if (sc->bpf) { bpf_mtap(sc->bpf, head); /* * Note that the interface cannot be in promiscuous mode if * there are no BPF listeners. And if we are in promiscuous * mode, we have to check if this packet is really ours. * * XXX This test does not support multicasts. */ if ((sc->arpcom.ac_if.if_flags & IFF_PROMISC) && bcmp(eh->ether_dhost, sc->arpcom.ac_enaddr, sizeof(eh->ether_dhost)) != 0 && bcmp(eh->ether_dhost, etherbroadcastaddr, sizeof(eh->ether_dhost)) != 0) { m_freem(head); return; } } #endif /* * Fix up data start offset in mbuf to point past ether header */ m_adj(head, sizeof(struct ether_header)); ether_input(&sc->arpcom.ac_if, eh, head); return; bad: if (head) m_freem(head); return; } /* * Supporting routines */ /* * Given a source and destination address, copy 'amount' of a packet from * the ring buffer into a linear destination buffer. Takes into account * ring-wrap. */ static inline char * ae_ring_copy(sc,src,dst,amount) struct ae_softc *sc; char *src; char *dst; u_short amount; { u_short tmp_amount; /* does copy wrap to lower addr in ring buffer? */ if (src + amount > sc->smem_end) { tmp_amount = sc->smem_end - src; bbcopy(src, dst, tmp_amount);/* copy amount up to end of smem */ amount -= tmp_amount; src = sc->smem_ring; dst += tmp_amount; } bbcopy(src, dst, amount); return(src + amount); } /* * Copy data from receive buffer to end of mbuf chain * allocate additional mbufs as needed. return pointer * to last mbuf in chain. * sc = ed info (softc) * src = pointer in ed ring buffer * dst = pointer to last mbuf in mbuf chain to copy to * amount = amount of data to copy */ struct mbuf * ae_ring_to_mbuf(sc,src,dst,total_len) struct ae_softc *sc; char *src; struct mbuf *dst; u_short total_len; { register struct mbuf *m = dst; while (total_len) { register u_short amount = min(total_len, M_TRAILINGSPACE(m)); if (amount == 0) { /* no more data in this mbuf, alloc another */ /* * If there is enough data for an mbuf cluster, attempt * to allocate one of those, otherwise, a regular * mbuf will do. * Note that a regular mbuf is always required, even if * we get a cluster - getting a cluster does not * allocate any mbufs, and one is needed to assign * the cluster to. The mbuf that has a cluster * extension can not be used to contain data - only * the cluster can contain data. */ dst = m; MGET(m, M_DONTWAIT, MT_DATA); if (m == 0) return (0); if (total_len >= MINCLSIZE) MCLGET(m, M_DONTWAIT); m->m_len = 0; dst->m_next = m; amount = min(total_len, M_TRAILINGSPACE(m)); } src = ae_ring_copy(sc, src, mtod(m, caddr_t) + m->m_len, amount); m->m_len += amount; total_len -= amount; } return (m); }