/* * Copyright (c) 1994 Christian E. Hopps * Copyright (c) 1990 The Regents of the University of California. * All rights reserved. * * This code is derived from software contributed to Berkeley by * Van Jacobson of Lawrence Berkeley Laboratory. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the University of * California, Berkeley and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)scsi.c 7.5 (Berkeley) 5/4/91 * $Id: sbic.c,v 1.2 1994/05/12 06:43:09 chopps Exp $ */ /* * AMIGA AMD 33C93 scsi adaptor driver */ /* need to know if any tapes have been configured */ #include "st.h" #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* * SCSI delays * In u-seconds, primarily for state changes on the SPC. */ #define SBIC_CMD_WAIT 50000 /* wait per step of 'immediate' cmds */ #define SBIC_DATA_WAIT 50000 /* wait per data in/out step */ #define SBIC_INIT_WAIT 50000 /* wait per step (both) during init */ #define b_cylin b_resid #define SBIC_WAIT(regs, until, timeo) sbicwait(regs, until, timeo, __LINE__) extern u_int kvtop(); int sbicicmd __P((struct sbic_softc *, int, void *, int, void *, int,u_char)); int sbicgo __P((struct sbic_softc *, struct scsi_xfer *)); int sbicdmaok __P((struct sbic_softc *, struct scsi_xfer *)); int sbicgetsense __P((struct sbic_softc *, struct scsi_xfer *)); int sbicwait __P((sbic_regmap_p, char, int , int)); int sbiccheckdmap __P((void *, u_long, u_long)); int sbicselectbus __P((struct sbic_softc *, sbic_regmap_p, u_char, u_char)); int sbicxfstart __P((sbic_regmap_p, int, u_char, int)); int sbicxfout __P((sbic_regmap_p regs, int, void *, int)); int sbicfromscsiperiod __P((struct sbic_softc *, sbic_regmap_p, int)); int sbictoscsiperiod __P((struct sbic_softc *, sbic_regmap_p, int)); int sbicintr __P((struct sbic_softc *)); void sbicxfin __P((sbic_regmap_p regs, int, void *)); void sbicxfdone __P((struct sbic_softc *, sbic_regmap_p, int)); void sbicabort __P((struct sbic_softc *, sbic_regmap_p, char *)); void sbicerror __P((struct sbic_softc *, sbic_regmap_p, u_char)); void sbicstart __P((struct sbic_softc *)); void sbicreset __P((struct sbic_softc *)); void sbicsetdelay __P((int)); void sbic_scsidone __P((struct sbic_softc *, int)); void sbic_donextcmd __P((struct sbic_softc *)); /* * Synch xfer parameters, and timing conversions */ int sbic_min_period = SBIC_SYN_MIN_PERIOD; /* in cycles = f(ICLK,FSn) */ int sbic_max_offset = SBIC_SYN_MAX_OFFSET; /* pure number */ int sbic_cmd_wait = SBIC_CMD_WAIT; int sbic_data_wait = SBIC_DATA_WAIT; int sbic_init_wait = SBIC_INIT_WAIT; /* * was broken before.. now if you want this you get it for all drives * on sbic controllers. */ int sbic_inhibit_sync = 1; int sbic_clock_override = 0; int sbic_no_dma = 0; #ifdef DEBUG #define QPRINTF(a) if (sbic_debug > 1) printf a int sbic_debug = 0; int sync_debug = 0; int sbic_dma_debug = 0; #else #define QPRINTF #endif /* * default minphys routine for sbic based controllers */ void sbic_minphys(bp) struct buf *bp; { /* * no max transfer at this level */ } /* * must be used */ u_int sbic_adinfo() { /* * one request at a time please */ return(1); } /* * used by specific sbic controller * * it appears that the higher level code does nothing with LUN's * so I will too. I could plug it in, however so could they * in scsi_scsi_cmd(). */ int sbic_scsicmd(xs) struct scsi_xfer *xs; { struct sbic_pending *pendp; struct sbic_softc *dev; struct scsi_link *slp; int flags, s; slp = xs->sc_link; dev = slp->adapter_softc; flags = xs->flags; if (flags & SCSI_DATA_UIO) panic("sbic: scsi data uio requested"); if (dev->sc_xs && flags & SCSI_NOMASK) panic("sbic_scsicmd: busy"); s = splbio(); pendp = &dev->sc_xsstore[slp->target][slp->lun]; if (pendp->xs) { splx(s); return(TRY_AGAIN_LATER); } if (dev->sc_xs) { pendp->xs = xs; TAILQ_INSERT_TAIL(&dev->sc_xslist, pendp, link); splx(s); return(SUCCESSFULLY_QUEUED); } pendp->xs = NULL; dev->sc_xs = xs; splx(s); /* * nothing is pending do it now. */ sbic_donextcmd(dev); if (flags & SCSI_NOMASK) return(COMPLETE); return(SUCCESSFULLY_QUEUED); } /* * entered with dev->sc_xs pointing to the next xfer to perform */ void sbic_donextcmd(dev) struct sbic_softc *dev; { struct scsi_xfer *xs; struct scsi_link *slp; int flags, phase, stat; xs = dev->sc_xs; slp = xs->sc_link; flags = xs->flags; if (flags & SCSI_DATA_IN) phase = DATA_IN_PHASE; else if (flags & SCSI_DATA_OUT) phase = DATA_OUT_PHASE; else phase = STATUS_PHASE; if (flags & SCSI_RESET) sbicreset(dev); dev->sc_stat[0] = -1; if (phase == STATUS_PHASE || flags & SCSI_NOMASK || sbicdmaok(dev, xs) == 0) stat = sbicicmd(dev, slp->target, xs->cmd, xs->cmdlen, xs->data, xs->datalen, phase); else if (sbicgo(dev, xs) == 0) return; else stat = dev->sc_stat[0]; sbic_scsidone(dev, stat); } void sbic_scsidone(dev, stat) struct sbic_softc *dev; int stat; { struct sbic_pending *pendp; struct scsi_xfer *xs; int s, donext; xs = dev->sc_xs; #ifdef DIAGNOSTIC if (xs == NULL) panic("sbic_scsidone"); #endif /* * is this right? */ xs->status = stat; if (stat == 0 || xs->flags & SCSI_ERR_OK) xs->resid = 0; else { switch(stat) { case SCSI_CHECK: if (stat = sbicgetsense(dev, xs)) goto bad_sense; xs->error = XS_SENSE; break; case SCSI_BUSY: xs->error = XS_BUSY; break; bad_sense: default: xs->error = XS_DRIVER_STUFFUP; QPRINTF(("sbic_scsicmd() bad %x\n", stat)); break; } } xs->flags |= ITSDONE; /* * grab next command before scsi_done() * this way no single device can hog scsi resources. */ s = splbio(); pendp = dev->sc_xslist.tqh_first; if (pendp == NULL) { donext = 0; dev->sc_xs = NULL; } else { donext = 1; TAILQ_REMOVE(&dev->sc_xslist, pendp, link); dev->sc_xs = pendp->xs; pendp->xs = NULL; } splx(s); scsi_done(xs); if (donext) sbic_donextcmd(dev); } int sbicgetsense(dev, xs) struct sbic_softc *dev; struct scsi_xfer *xs; { struct scsi_sense rqs; struct scsi_link *slp; int stat; slp = xs->sc_link; rqs.op_code = REQUEST_SENSE; rqs.byte2 = slp->lun << 5; #ifdef not_yet rqs.length = xs->req_sense_length ? xs->req_sense_length : sizeof(xs->sense); #else rqs.length = sizeof(xs->sense); #endif rqs.unused[0] = rqs.unused[1] = rqs.control = 0; return(sbicicmd(dev, slp->target, &rqs, sizeof(rqs), &xs->sense, rqs.length, DATA_IN_PHASE)); } int sbicdmaok(dev, xs) struct sbic_softc *dev; struct scsi_xfer *xs; { if (sbic_no_dma || xs->datalen & 0x1 || (u_int)xs->data & 0x3) return(0); /* * controller supports dma to any addresses? */ else if ((dev->sc_flags & SBICF_BADDMA) == 0) return(1); /* * this address is ok for dma? */ else if (sbiccheckdmap(xs->data, xs->datalen, dev->sc_dmamask) == 0) return(1); /* * we have a bounce buffer? */ else if (dev->sc_dmabuffer) return(1); return(0); } int sbicwait(regs, until, timeo, line) sbic_regmap_p regs; char until; int timeo; int line; { u_char val; int csr; if (timeo == 0) timeo = 1000000; /* some large value.. */ GET_SBIC_asr(regs,val); while ((val & until) == 0) { if (timeo-- == 0) { GET_SBIC_csr(regs, csr); printf("sbicwait TIMEO @%d with asr=x%x csr=x%x\n", line, val, csr); break; } DELAY(1); GET_SBIC_asr(regs,val); } return(val); } void sbicabort(dev, regs, where) struct sbic_softc *dev; sbic_regmap_p regs; char *where; { u_char csr, asr; GET_SBIC_csr(regs, csr); GET_SBIC_asr(regs, asr); printf ("%s: abort %s: csr = 0x%02x, asr = 0x%02x\n", dev->sc_dev.dv_xname, where, csr, asr); if (dev->sc_flags & SBICF_SELECTED) { SET_SBIC_cmd(regs, SBIC_CMD_ABORT); WAIT_CIP(regs); GET_SBIC_asr(regs, asr); if (asr & (SBIC_ASR_BSY|SBIC_ASR_LCI)) { /* ok, get more drastic.. */ SET_SBIC_cmd (regs, SBIC_CMD_RESET); DELAY(25); SBIC_WAIT(regs, SBIC_ASR_INT, 0); /* clears interrupt also */ GET_SBIC_csr (regs, csr); dev->sc_flags &= ~SBICF_SELECTED; return; } do { SBIC_WAIT (regs, SBIC_ASR_INT, 0); GET_SBIC_csr (regs, csr); } while ((csr != SBIC_CSR_DISC) && (csr != SBIC_CSR_DISC_1) && (csr != SBIC_CSR_CMD_INVALID)); /* lets just hope it worked.. */ dev->sc_flags &= ~SBICF_SELECTED; } } /* * XXX Set/reset long delays. * * if delay == 0, reset default delays * if delay < 0, set both delays to default long initialization values * if delay > 0, set both delays to this value * * Used when a devices is expected to respond slowly (e.g. during * initialization). */ void sbicsetdelay(del) int del; { static int saved_cmd_wait, saved_data_wait; if (del) { saved_cmd_wait = sbic_cmd_wait; saved_data_wait = sbic_data_wait; if (del > 0) sbic_cmd_wait = sbic_data_wait = del; else sbic_cmd_wait = sbic_data_wait = sbic_init_wait; } else { sbic_cmd_wait = saved_cmd_wait; sbic_data_wait = saved_data_wait; } } void sbicreset(dev) struct sbic_softc *dev; { sbic_regmap_p regs; u_int i, s; u_char my_id, csr; regs = dev->sc_sbicp; if (dev->sc_flags & SBICF_ALIVE) sbicabort(dev, regs, "reset"); s = splbio(); /* preserve our ID for now */ GET_SBIC_myid (regs, my_id); my_id &= SBIC_ID_MASK; if (dev->sc_clkfreq < 110) my_id |= SBIC_ID_FS_8_10; else if (dev->sc_clkfreq < 160) my_id |= SBIC_ID_FS_12_15; else if (dev->sc_clkfreq < 210) my_id |= SBIC_ID_FS_16_20; my_id |= SBIC_ID_EAF /*| SBIC_ID_EHP*/ ; SET_SBIC_myid(regs, my_id); /* * Disable interrupts (in dmainit) then reset the chip */ SET_SBIC_cmd(regs, SBIC_CMD_RESET); DELAY(25); SBIC_WAIT(regs, SBIC_ASR_INT, 0); GET_SBIC_csr(regs, csr); /* clears interrupt also */ /* * Set up various chip parameters */ SET_SBIC_control(regs, SBIC_CTL_EDI | SBIC_CTL_IDI | SBIC_MACHINE_DMA_MODE); /* * don't allow (re)selection (SBIC_RID_ES) * until we can handle target mode!! */ SET_SBIC_rselid(regs, 0); SET_SBIC_syn(regs, 0); /* asynch for now */ /* * anything else was zeroed by reset */ splx(s); dev->sc_flags |= SBICF_ALIVE; dev->sc_flags &= ~SBICF_SELECTED; } void sbicerror(dev, regs, csr) struct sbic_softc *dev; sbic_regmap_p regs; u_char csr; { struct scsi_xfer *xs; xs = dev->sc_xs; #ifdef DIAGNOSTIC if (xs == NULL) panic("sbicerror"); #endif if (xs->flags & SCSI_SILENT) return; printf("%s: ", dev->sc_dev.dv_xname); printf("csr == 0x%02i\n", csr); /* XXX */ } /* * select the bus, return when selected or error. */ int sbicselectbus(dev, regs, target, our_addr) struct sbic_softc *dev; sbic_regmap_p regs; u_char target, our_addr; { u_char asr, csr, id; QPRINTF(("sbicselectbus %d\n", target)); /* * if we're already selected, return (XXXX panic maybe?) */ if (dev->sc_flags & SBICF_SELECTED) return(1); /* * issue select */ SBIC_TC_PUT(regs, 0); SET_SBIC_selid(regs, target); SET_SBIC_timeo(regs, SBIC_TIMEOUT(250,dev->sc_clkfreq)); /* * set sync or async */ if (dev->sc_sync[target].state == SYNC_DONE) SET_SBIC_syn(regs, SBIC_SYN (dev->sc_sync[target].offset, dev->sc_sync[target].period)); else SET_SBIC_syn(regs, SBIC_SYN (0, sbic_min_period)); SET_SBIC_cmd(regs, SBIC_CMD_SEL_ATN); /* * wait for select (merged from seperate function may need * cleanup) */ WAIT_CIP(regs); do { SBIC_WAIT(regs, SBIC_ASR_INT, 0); GET_SBIC_csr (regs, csr); QPRINTF(("%02x ", csr)); } while (csr != (SBIC_CSR_MIS_2|MESG_OUT_PHASE) && csr != (SBIC_CSR_MIS_2|CMD_PHASE) && csr != SBIC_CSR_SEL_TIMEO); if (csr == (SBIC_CSR_MIS_2|CMD_PHASE)) dev->sc_flags |= SBICF_SELECTED; /* device ignored ATN */ else if (csr == (SBIC_CSR_MIS_2|MESG_OUT_PHASE)) { /* * Send identify message * (SCSI-2 requires an identify msg (?)) */ GET_SBIC_selid(regs, id); /* * handle drives that don't want to be asked * whether to go sync at all. */ if (sbic_inhibit_sync && dev->sc_sync[id].state == SYNC_START) { #ifdef DEBUG if (sync_debug) printf("Forcing target %d asynchronous.\n", id); #endif dev->sc_sync[id].offset = 0; dev->sc_sync[id].period = sbic_min_period; dev->sc_sync[id].state = SYNC_DONE; } if (dev->sc_sync[id].state != SYNC_START) SEND_BYTE (regs, MSG_IDENTIFY); else { /* * try to initiate a sync transfer. * So compose the sync message we're going * to send to the target */ #ifdef DEBUG if (sync_debug) printf("Sending sync request to target %d ... ", id); #endif /* * setup scsi message sync message request */ dev->sc_msg[0] = MSG_IDENTIFY; dev->sc_msg[1] = MSG_EXT_MESSAGE; dev->sc_msg[2] = 3; dev->sc_msg[3] = MSG_SYNC_REQ; dev->sc_msg[4] = sbictoscsiperiod(dev, regs, sbic_min_period); dev->sc_msg[5] = sbic_max_offset; if (sbicxfstart(regs, 6, MESG_OUT_PHASE, sbic_cmd_wait)) sbicxfout(regs, 6, dev->sc_msg, MESG_OUT_PHASE); dev->sc_sync[id].state = SYNC_SENT; #ifdef DEBUG if (sync_debug) printf ("sent\n"); #endif } SBIC_WAIT (regs, SBIC_ASR_INT, 0); GET_SBIC_csr (regs, csr); QPRINTF(("[%02x]", csr)); #ifdef DEBUG if (sync_debug && dev->sc_sync[id].state == SYNC_SENT) printf("csr-result of last msgout: 0x%x\n", csr); #endif if (csr != SBIC_CSR_SEL_TIMEO) dev->sc_flags |= SBICF_SELECTED; } QPRINTF(("\n")); return(csr == SBIC_CSR_SEL_TIMEO); } int sbicxfstart(regs, len, phase, wait) sbic_regmap_p regs; int len, wait; u_char phase; { u_char id; if (phase == DATA_IN_PHASE || phase == MESG_IN_PHASE) { GET_SBIC_selid (regs, id); id |= SBIC_SID_FROM_SCSI; SET_SBIC_selid (regs, id); SBIC_TC_PUT (regs, (unsigned)len); } else if (phase == DATA_OUT_PHASE || phase == MESG_OUT_PHASE || phase == CMD_PHASE) SBIC_TC_PUT (regs, (unsigned)len); else SBIC_TC_PUT (regs, 0); QPRINTF(("sbicxfstart %d, %d, %d\n", len, phase, wait)); return(1); } int sbicxfout(regs, len, bp, phase) sbic_regmap_p regs; int len; void *bp; int phase; { u_char orig_csr, csr, asr, *buf; int wait; buf = bp; wait = sbic_data_wait; QPRINTF(("sbicxfout {%d} %02x %02x %02x %02x %02x " "%02x %02x %02x %02x %02x\n", len, buf[0], buf[1], buf[2], buf[3], buf[4], buf[5], buf[6], buf[7], buf[8], buf[9])); GET_SBIC_csr (regs, orig_csr); /* * sigh.. WD-PROTO strikes again.. sending the command in one go * causes the chip to lock up if talking to certain (misbehaving?) * targets. Anyway, this procedure should work for all targets, but * it's slightly slower due to the overhead */ WAIT_CIP (regs); SET_SBIC_cmd (regs, SBIC_CMD_XFER_INFO); for (;len > 0; len--) { GET_SBIC_asr (regs, asr); while ((asr & SBIC_ASR_DBR) == 0) { if ((asr & SBIC_ASR_INT) || --wait < 0) { #ifdef DEBUG if (sbic_debug) printf("sbicxfout fail: l%d i%x w%d\n", len, asr, wait); #endif return (len); } DELAY(1); GET_SBIC_asr (regs, asr); } SET_SBIC_data (regs, *buf); buf++; } QPRINTF(("sbicxfout done\n")); /* * this leaves with one csr to be read */ return(0); } void sbicxfin(regs, len, bp) sbic_regmap_p regs; int len; void *bp; { int wait; u_char *obp, *buf; u_char orig_csr, csr, asr; wait = sbic_data_wait; obp = bp; buf = bp; GET_SBIC_csr (regs, orig_csr); QPRINTF(("sbicxfin %d, csr=%02x\n", len, orig_csr)); WAIT_CIP (regs); SET_SBIC_cmd (regs, SBIC_CMD_XFER_INFO); for (;len > 0; len--) { GET_SBIC_asr (regs, asr); while ((asr & SBIC_ASR_DBR) == 0) { if ((asr & SBIC_ASR_INT) || --wait < 0) { #ifdef DEBUG if (sbic_debug) printf("sbicxfin fail: l%d i%x w%d\n", len, asr, wait); #endif return; } DELAY(1); GET_SBIC_asr (regs, asr); } GET_SBIC_data (regs, *buf); buf++; } QPRINTF(("sbicxfin {%d} %02x %02x %02x %02x %02x %02x " "%02x %02x %02x %02x\n", len, obp[0], obp[1], obp[2], obp[3], obp[4], obp[5], obp[6], obp[7], obp[8], obp[9])); /* this leaves with one csr to be read */ } /* * SCSI 'immediate' command: issue a command to some SCSI device * and get back an 'immediate' response (i.e., do programmed xfer * to get the response data). 'cbuf' is a buffer containing a scsi * command of length clen bytes. 'buf' is a buffer of length 'len' * bytes for data. The transfer direction is determined by the device * (i.e., by the scsi bus data xfer phase). If 'len' is zero, the * command must supply no data. 'xferphase' is the bus phase the * caller expects to happen after the command is issued. It should * be one of DATA_IN_PHASE, DATA_OUT_PHASE or STATUS_PHASE. */ int sbicicmd(dev, target, cbuf, clen, buf, len, xferphase) struct sbic_softc *dev; void *cbuf, *buf; int clen, len; u_char xferphase; { sbic_regmap_p regs; u_char phase, csr, asr; int wait; regs = dev->sc_sbicp; /* * set the sbic into non-DMA mode */ SET_SBIC_control(regs, SBIC_CTL_EDI | SBIC_CTL_IDI); retry_selection: /* * select the SCSI bus (it's an error if bus isn't free) */ if (sbicselectbus(dev, regs, target, dev->sc_scsiaddr)) return(-1); /* * Wait for a phase change (or error) then let the device sequence * us through the various SCSI phases. */ dev->sc_stat[0] = 0xff; dev->sc_msg[0] = 0xff; phase = CMD_PHASE; new_phase: wait = sbic_cmd_wait; GET_SBIC_csr (regs, csr); QPRINTF((">CSR:%02x<", csr)); /* * requesting some new phase */ if ((csr != 0xff) && (csr & 0xf0) && (csr & 0x08)) phase = csr & PHASE; else if ((csr == SBIC_CSR_DISC) || (csr == SBIC_CSR_DISC_1) || (csr == SBIC_CSR_S_XFERRED)) { dev->sc_flags &= ~SBICF_SELECTED; GET_SBIC_cmd_phase (regs, phase); if (phase == 0x60) GET_SBIC_tlun (regs, dev->sc_stat[0]); else return(-1); goto out; } else { sbicerror(dev, regs, csr); goto abort; } switch (phase) { case CMD_PHASE: if (sbicxfstart (regs, clen, phase, wait)) if (sbicxfout (regs, clen, cbuf, phase)) goto abort; phase = xferphase; break; case DATA_IN_PHASE: if (len <= 0) goto abort; wait = sbic_data_wait; if (sbicxfstart(regs, len, phase, wait)) sbicxfin(regs, len, buf); phase = STATUS_PHASE; break; case MESG_IN_PHASE: if (sbicxfstart(regs, sizeof(dev->sc_msg), phase, wait) == 0) break; dev->sc_msg[0] = 0xff; sbicxfin(regs, sizeof(dev->sc_msg), dev->sc_msg); /* * get the command completion interrupt, or we * can't send a new command (LCI) */ SBIC_WAIT(regs, SBIC_ASR_INT, wait); GET_SBIC_csr(regs, csr); #ifdef DEBUG if (sync_debug) printf("msgin done csr 0x%x\n", csr); #endif /* * test whether this is a reply to our sync * request */ if (dev->sc_msg[0] == MSG_EXT_MESSAGE && dev->sc_msg[1] == 3 && dev->sc_msg[2] == MSG_SYNC_REQ) { dev->sc_sync[target].period = sbicfromscsiperiod(dev, regs, dev->sc_msg[3]); dev->sc_sync[target].offset = dev->sc_msg[4]; dev->sc_sync[target].state = SYNC_DONE; SET_SBIC_syn(regs, SBIC_SYN(dev->sc_sync[target].offset, dev->sc_sync[target].period)); /* ACK the message */ SET_SBIC_cmd(regs, SBIC_CMD_CLR_ACK); WAIT_CIP(regs); phase = CMD_PHASE; /* or whatever */ printf("%s: target %d now synchronous," " period=%dns, offset=%d.\n", dev->sc_dev.dv_xname, target, dev->sc_msg[3] * 4, dev->sc_msg[4]); } else if (dev->sc_msg[0] == MSG_REJECT && dev->sc_sync[target].state == SYNC_SENT) { #ifdef DEBUG if (sync_debug) printf("target %d rejected sync, going async\n", target); #endif dev->sc_sync[target].period = sbic_min_period; dev->sc_sync[target].offset = 0; dev->sc_sync[target].state = SYNC_DONE; SET_SBIC_syn(regs, SBIC_SYN(dev->sc_sync[target].offset, dev->sc_sync[target].period)); /* ACK the message */ SET_SBIC_cmd(regs, SBIC_CMD_CLR_ACK); WAIT_CIP(regs); phase = CMD_PHASE; /* or whatever */ } else if (dev->sc_msg[0] == MSG_REJECT) { /* * we'll never REJECt a REJECT message.. */ /* ACK the message */ SET_SBIC_cmd(regs, SBIC_CMD_CLR_ACK); WAIT_CIP(regs); phase = CMD_PHASE; /* or whatever */ } else if (dev->sc_msg[0] == MSG_CMD_COMPLETE) { /* !! KLUDGE ALERT !! quite a few drives don't seem to * really like the current way of sending the * sync-handshake together with the ident-message, and * they react by sending command-complete and * disconnecting right after returning the valid sync * handshake. So, all I can do is reselect the drive, * and hope it won't disconnect again. I don't think * this is valid behavior, but I can't help fixing a * problem that apparently exists. * * Note: we should not get here on `normal' command * completion, as that condition is handled by the * high-level sel&xfer resume command used to walk * thru status/cc-phase. */ #ifdef DEBUG if (sync_debug) printf ("GOT CMD-COMPLETE! %d acting weird.." " waiting for disconnect...\n", target); #endif /* ACK the message */ SET_SBIC_cmd (regs, SBIC_CMD_CLR_ACK); WAIT_CIP(regs); /* wait for disconnect */ while (csr != SBIC_CSR_DISC && csr != SBIC_CSR_DISC_1) { DELAY(1); GET_SBIC_csr(regs, csr); } #ifdef DEBUG if (sync_debug) printf ("ok.\nRetrying selection.\n"); #endif dev->sc_flags &= ~SBICF_SELECTED; goto retry_selection; } else { #ifdef DEBUG if (sbic_debug || sync_debug) printf ("Rejecting message 0x%02x\n", dev->sc_msg[0]); #endif /* prepare to reject the message, NACK */ SET_SBIC_cmd(regs, SBIC_CMD_SET_ATN); WAIT_CIP(regs); SET_SBIC_cmd(regs, SBIC_CMD_CLR_ACK); WAIT_CIP(regs); phase = MESG_OUT_PHASE; } break; case MESG_OUT_PHASE: #ifdef DEBUG if (sync_debug) printf ("sending REJECT msg to last msg.\n"); #endif /* * should only get here on reject, * since it's always US that * initiate a sync transfer */ SEND_BYTE(regs, MSG_REJECT); phase = STATUS_PHASE; break; case DATA_OUT_PHASE: if (len <= 0) goto abort; wait = sbic_data_wait; if (sbicxfstart(regs, len, phase, wait)) if (sbicxfout (regs, len, buf, phase)) goto abort; phase = STATUS_PHASE; break; case STATUS_PHASE: /* * the sbic does the status/cmd-complete reading ok, * so do this with its hi-level commands. */ SBIC_TC_PUT(regs, 0); SET_SBIC_cmd_phase(regs, 0x46); SET_SBIC_cmd(regs, SBIC_CMD_SEL_ATN_XFER); phase = BUS_FREE_PHASE; break; case BUS_FREE_PHASE: goto out; default: printf("%s: unexpected phase %d in icmd from %d\n", dev->sc_dev.dv_xname, phase, target); goto abort; } /* * make sure the last command was taken, * ie. we're not hunting after an ignored command.. */ GET_SBIC_asr(regs, asr); if (asr & SBIC_ASR_LCI) goto abort; /* tapes may take a loooong time.. */ while (asr & SBIC_ASR_BSY) { DELAY(1); GET_SBIC_asr(regs, asr); } /* * wait for last command to complete */ SBIC_WAIT (regs, SBIC_ASR_INT, wait); /* * do it again */ goto new_phase; abort: sbicabort(dev, regs, "icmd"); out: QPRINTF(("=STS:%02x=", dev->sc_stat[0])); return(dev->sc_stat[0]); } /* * Finish SCSI xfer command: After the completion interrupt from * a read/write operation, sequence through the final phases in * programmed i/o. This routine is a lot like sbicicmd except we * skip (and don't allow) the select, cmd out and data in/out phases. */ void sbicxfdone(dev, regs, target) struct sbic_softc *dev; sbic_regmap_p regs; int target; { u_char phase, csr; int s; QPRINTF(("{")); s = splbio(); /* * have the sbic complete on its own */ SBIC_TC_PUT(regs, 0); SET_SBIC_cmd_phase(regs, 0x46); SET_SBIC_cmd(regs, SBIC_CMD_SEL_ATN_XFER); do { SBIC_WAIT (regs, SBIC_ASR_INT, 0); GET_SBIC_csr (regs, csr); QPRINTF(("%02x:", csr)); } while ((csr != SBIC_CSR_DISC) && (csr != SBIC_CSR_DISC_1) && (csr != SBIC_CSR_S_XFERRED)); dev->sc_flags &= ~SBICF_SELECTED; GET_SBIC_cmd_phase (regs, phase); QPRINTF(("}%02x", phase)); if (phase == 0x60) GET_SBIC_tlun(regs, dev->sc_stat[0]); else sbicerror(dev, regs, csr); QPRINTF(("=STS:%02x=\n", dev->sc_stat[0])); splx(s); } int sbicgo(dev, xs) struct sbic_softc *dev; struct scsi_xfer *xs; { int i, dmaflags, count, tcount, target; u_char phase, csr, asr, cmd, *addr; sbic_regmap_p regs; struct dma_chain *dcp; char *dmaend; int wait; target = xs->sc_link->target; count = xs->datalen; addr = xs->data; regs = dev->sc_sbicp; dmaend = NULL; /* * set the sbic into DMA mode */ SET_SBIC_control(regs, SBIC_CTL_EDI | SBIC_CTL_IDI | SBIC_MACHINE_DMA_MODE); /* * select the SCSI bus (it's an error if bus isn't free) */ if (sbicselectbus(dev, regs, target, dev->sc_scsiaddr)) { dev->sc_dmafree(dev); return(-1); } /* * Wait for a phase change (or error) then let the device * sequence us through command phase (we may have to take * a msg in/out before doing the command). If the disk has * to do a seek, it may be a long time until we get a change * to data phase so, in the absense of an explicit phase * change, we assume data phase will be coming up and tell * the SPC to start a transfer whenever it does. We'll get * a service required interrupt later if this assumption is * wrong. Otherwise we'll get a service required int when * the transfer changes to status phase. */ phase = CMD_PHASE; new_phase: wait = sbic_cmd_wait; switch (phase) { case CMD_PHASE: if (sbicxfstart(regs, xs->cmdlen, phase, wait)) if (sbicxfout(regs, xs->cmdlen, xs->cmd, phase)) goto abort; break; case MESG_IN_PHASE: if (sbicxfstart(regs, sizeof(dev->sc_msg), phase, wait) == 0) break; sbicxfin(regs, sizeof(dev->sc_msg), dev->sc_msg); /* * prepare to reject any mesgin, * no matter what it might be.. */ SET_SBIC_cmd(regs, SBIC_CMD_SET_ATN); WAIT_CIP(regs); SET_SBIC_cmd(regs, SBIC_CMD_CLR_ACK); phase = MESG_OUT_PHASE; break; case MESG_OUT_PHASE: SEND_BYTE(regs, MSG_REJECT); phase = STATUS_PHASE; break; case DATA_IN_PHASE: case DATA_OUT_PHASE: goto out; /* * status phase can happen, if the issued read/write command * is illegal (for example, reading after EOT on tape) and the * device doesn't even go to data in/out phase. So handle this * here normally, instead of going thru abort-handling. */ case STATUS_PHASE: dev->sc_dmafree(dev); sbicxfdone(dev, regs, target); dev->sc_flags &= ~(SBICF_INDMA | SBICF_BBUF); sbic_scsidone(dev, dev->sc_stat[0]); return(0); default: printf("%s: unexpected phase %d in go from %d\n", phase, dev->sc_dev.dv_xname, target); goto abort; } /* * make sure the last command was taken, * ie. we're not hunting after an ignored command.. */ GET_SBIC_asr(regs, asr); if (asr & SBIC_ASR_LCI) goto abort; /* * tapes may take a loooong time.. */ while (asr & SBIC_ASR_BSY) { DELAY(1); GET_SBIC_asr(regs, asr); } if (wait <= 0) goto abort; /* * wait for last command to complete */ SBIC_WAIT(regs, SBIC_ASR_INT, wait); GET_SBIC_csr(regs, csr); QPRINTF((">CSR:%02x<", csr)); /* * requesting some new phase */ if ((csr != 0xff) && (csr & 0xf0) && (csr & 0x08)) phase = csr & PHASE; else { sbicerror(dev, regs, csr); goto abort; } /* * start again with for new phase */ goto new_phase; out: dmaflags = 0; if (xs->flags & SCSI_DATA_IN) dmaflags |= DMAGO_READ; if (count > MAXPHYS) printf("sbicgo: bp->b_bcount > MAXPHYS %08x\n", count); if (dev->sc_flags & SBICF_BADDMA && sbiccheckdmap(addr, count, dev->sc_dmamask)) { /* * need to bounce the dma. */ if (dmaflags & DMAGO_READ) { dev->sc_flags |= SBICF_BBUF; dev->sc_dmausrbuf = addr; dev->sc_dmausrlen = count; } else { /* write: copy to dma buffer */ bcopy (addr, dev->sc_dmabuffer, count); } addr = dev->sc_dmabuffer; /* and use dma buffer */ } #ifdef DEBUG if (sbic_dma_debug & DDB_FOLLOW) printf("sbicgo(%d, %x, %x, %x)\n", dev->sc_dev.dv_unit, addr, count, dmaflags); #endif /* * Build the DMA chain */ for (dcp = dev->sc_chain; count > 0; dcp++) { dcp->dc_addr = (char *) kvtop(addr); if (count < (tcount = NBPG - ((int)addr & PGOFSET))) tcount = count; addr += tcount; count -= tcount; dcp->dc_count = tcount >> 1; /* * check if contigous, if not mark new end * else increment end and count on previous. */ if (dcp->dc_addr != dmaend) dmaend = dcp->dc_addr + tcount; else { dcp--; dmaend += tcount; dcp->dc_count += tcount >> 1; } } dev->sc_cur = dev->sc_chain; dev->sc_last = --dcp; dev->sc_tcnt = dev->sc_cur->dc_count << 1; #ifdef DEBUG if (sbic_dma_debug & DDB_IO) { for (dcp = dev->sc_chain; dcp <= dev->sc_last; dcp++) printf(" %d: %d@%x\n", dcp-dev->sc_chain, dcp->dc_count, dcp->dc_addr); } #endif /* * push the data cash */ DCIS(); /* * dmago() also enables interrupts for the sbic */ i = dev->sc_dmago(dev, addr, xs->datalen, dmaflags); SBIC_TC_PUT(regs, (unsigned)i); SET_SBIC_cmd(regs, SBIC_CMD_XFER_INFO); return(0); abort: sbicabort(dev, regs, "go"); dev->sc_dmafree(dev); return(-1); } int sbicintr(dev) struct sbic_softc *dev; { sbic_regmap_p regs; u_char asr, csr; int i; regs = dev->sc_sbicp; /* * pending interrupt? */ GET_SBIC_asr (regs, asr); if ((asr & SBIC_ASR_INT) == 0) return(0); GET_SBIC_csr(regs, csr); QPRINTF(("[0x%x]", csr)); if (csr == (SBIC_CSR_XFERRED|STATUS_PHASE) || csr == (SBIC_CSR_MIS|STATUS_PHASE) || csr == (SBIC_CSR_MIS_1|STATUS_PHASE) || csr == (SBIC_CSR_MIS_2|STATUS_PHASE)) { /* * this should be the normal i/o completion case. * get the status & cmd complete msg then let the * device driver look at what happened. */ sbicxfdone(dev, regs, dev->sc_xs->sc_link->target); if (dev->sc_flags & SBICF_BBUF) bcopy(dev->sc_dmabuffer, dev->sc_dmausrbuf, dev->sc_dmausrlen); dev->sc_flags &= ~(SBICF_INDMA | SBICF_BBUF); dev->sc_dmafree(dev); sbic_scsidone(dev, dev->sc_stat[0]); } else if (csr == (SBIC_CSR_XFERRED|DATA_OUT_PHASE) || csr == (SBIC_CSR_XFERRED|DATA_IN_PHASE) || csr == (SBIC_CSR_MIS|DATA_OUT_PHASE) || csr == (SBIC_CSR_MIS|DATA_IN_PHASE) || csr == (SBIC_CSR_MIS_1|DATA_OUT_PHASE) || csr == (SBIC_CSR_MIS_1|DATA_IN_PHASE) || csr == (SBIC_CSR_MIS_2|DATA_OUT_PHASE) || csr == (SBIC_CSR_MIS_2|DATA_IN_PHASE)) { /* * do scatter-gather dma * hacking the controller chip, ouch.. */ /* * set next dma addr and dec count */ dev->sc_cur->dc_addr += dev->sc_tcnt; dev->sc_cur->dc_count -= (dev->sc_tcnt >> 1); if (dev->sc_cur->dc_count == 0) ++dev->sc_cur; /* advance to next segment */ i = dev->sc_dmanext(dev); SBIC_TC_PUT(regs, (unsigned)i); SET_SBIC_cmd(regs, SBIC_CMD_XFER_INFO); } else { /* * Something unexpected happened -- deal with it. */ dev->sc_dmastop(dev); sbicerror(dev, regs, csr); sbicabort(dev, regs, "intr"); if (dev->sc_flags & SBICF_INDMA) { dev->sc_flags &= ~(SBICF_INDMA | SBICF_BBUF); dev->sc_dmafree(dev); sbic_scsidone(dev, -1); } } return(1); } /* * Check if DMA can not be used with specified buffer */ int sbiccheckdmap(bp, len, mask) void *bp; u_long len, mask; { u_char *buffer; u_long phy_buf; u_long phy_len; buffer = bp; if (len == 0) return(0); while (len) { phy_buf = kvtop(buffer); if (len < (phy_len = NBPG - ((int) buffer & PGOFSET))) phy_len = len; if (phy_buf & mask) return(1); buffer += phy_len; len -= phy_len; } return(0); } int sbictoscsiperiod(dev, regs, a) struct sbic_softc *dev; sbic_regmap_p regs; int a; { unsigned int fs; /* * cycle = DIV / (2*CLK) * DIV = FS+2 * best we can do is 200ns at 20Mhz, 2 cycles */ GET_SBIC_myid(regs,fs); fs = (fs >>6) + 2; /* DIV */ fs = (fs * 10000) / (dev->sc_clkfreq<<1); /* Cycle, in ns */ if (a < 2) a = 8; /* map to Cycles */ return ((fs*a)>>2); /* in 4 ns units */ } int sbicfromscsiperiod(dev, regs, p) struct sbic_softc *dev; sbic_regmap_p regs; int p; { register unsigned int fs, ret; /* Just the inverse of the above */ GET_SBIC_myid(regs,fs); fs = (fs >>6) + 2; /* DIV */ fs = (fs * 10000) / (dev->sc_clkfreq<<1); /* Cycle, in ns */ ret = p << 2; /* in ns units */ ret = ret / fs; /* in Cycles */ if (ret < sbic_min_period) return(sbic_min_period); /* verify rounding */ if (sbictoscsiperiod(dev, regs, ret) < p) ret++; return (ret >= 8) ? 0 : ret; }