- allow get/set of enums SUNAUDIO_SOURCE and SUNAUDIO_OUTPUT rather
than returning EINVAL
- add missing SUNAUDIO_MONITOR_CLASS case in query_devinfo
- convert SUNAUDIO_MONITOR case from a MIXER_CLASS to a MIXER_VALUE
like it is supposed to be
- the labels for outputs/record class were swapped: fix it
this patch allows "mixerctl" to work properly on a sparc
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
* Carrier detect (TS_CARR_ON) is based on the actual DCD bit, even if it's
being ignored.
* Set TS_WOPEN early on in zsopen().
* Don't disable interrupts on the console during close if we have DDB.
Inert changes:
* Don't handle ZS_HWFLAG_NO_DCD here; the frontend does it.
* Deprecate `register'.
* Use SET(), CLR(), and ISSET().
More performance changes:
* Rototill receive handling; use a backpressure mechanism to prevent livelock.
* Output silo/ibuf overflow warnings at most once per minute, from a callout.
* When we exhaust the current transmit run, turn off transmit interrupts in
zstty_txint(), so we're fairly sure we don't get another one.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
control any more, and the speed of changing DTR isn't really an issue. Also,
the old code created a bug where zsparam() might have failed to set some
registers.
Change the interface to zs_hwiflow(); just have it use zst_rx_blocked.
Make zs_modem() a tiny bit faster.
Do RTS updates immediately; do not allow them to be held.
Stop output as fast as possible when DCD is deasserted.
Do *not* automatically drop DTR when DCD is deasserted.
Only check for rr0 bits that we care about (DTR and DCD).
Make sure we turn on DTR and/or RTS as appropriate during open.
Rearrange close sequence so the tty is flushed before turning off interrupts.
Deal with `softcar' and the console device by silently asserting CLOCAL and
|HUPCL, as in com driver.
Do *not* fiddle with DTR when changing the line speed.
Make sure we update the tty's carrier status when CLOCAL or MDMBUF is changed.
Only change rr1 when we actually need to turn on or off TIE.
things happen if we are the console.
Restore to the prevoius value (not to hardwired 8N1) because this
could be set by the serial console initialization.
Closed PR kern/4373 (Dave Huang)
in the ISR (from the ISA "ed" driver's generic 8390 probe routine).
Also, add a big comment describing exactly what we're checking when
probing for the dp8390 (also lifted from the ISA "ed" driver).
The RST check should help weed-out non-matches before they get to the
fairly invasive memory check.
should creation/initialization of a mscp fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one mscp what we can grab, and continue to hobble along.
Also, fix the mscp freelist fencepost error, similar to aha.c and bha.c
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
shoud creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
Adjust the number of ccbs allocated during initialization.
Every ccb could potentially lock 64k of memory for dma buffers if bounce
buffers are used. Instead of BHA_CCB_MAX ccbs using 2MByte, only
sc_link.openings ccbs per device are allocated. Thus we now use only
256KByte per device present.
(hannken)
Fix a couple of errors in bha_create_ccbs():
- Don't ever let the number of CCBs be creater than BHA_CCB_MAX.
- Fix a fencepost that caused the last CCB allocated to never be put
on the freelist.
(thorpej)
