- After reselect, don't clear ack after the IDENTIFY message, this breaks
when the reselecting target has different sync parameters than the previous
one.
'command slots' in which the host can put command and wait for the script
to start them
- Change siop.c to do full disconnect/reslelect, allowing as much as one
command per target/lun to run in parallel.
- Fix bug in registers init where a board without BIOS would end at
ID 0 (now the driver works on alpha too).
- better handling of messages, sending back a MSG_EXT_SDTR in response to an
incoming MSG_EXT_SDTR, and MSG_MESSAGE_REJECT for unhandled messages.
- fix use of bus_dmamap_sync() and htole32().
- supports shared interrups
- change some int8 and int16 to int, for alpha and mips benefits ( suggested by
Toru Nishimura)
(the name 'siop' is still being discussed, may change).
Only basic disconnect/reselect for now, no sync/wide negotiation.
Tested with 810A, 875 and 895 on i386 only.
The bus-independant part should also be able to handle the 53c720 and 53c770.
A new driver with enhanced script should appear for the 825/875/895 'soon'.
cycle to get rid of the old 1.31 firmware. *@!$&^@&$!&^&^!!!!!
But anyway comment it out and use new SBus 7.55 firmware. We get fast posting
with this as well as 32 luns and target mode support.
as with user-land programs, include files are installed by each directory
in the tree that has includes to install. (This allows more flexibility
as to what gets installed, makes 'partial installs' easier, and gives us
more options as to which machines' includes get installed at any given
time.) The old SYS_INCLUDES={symlinks,copies} behaviours are _both_
still supported, though at least one bug in the 'symlinks' case is
fixed by this change. Include files can't be build before installation,
so directories that have includes as targets (e.g. dev/pci) have to move
those targets into a different Makefile.
dev/microcode/aic7xxx_seq.h,
dev/ic/aic7xxxreg.h:
Remove intrinsic knowledge about SDTR and WDTR messages and replace it
with a generic message system that allows the kernel driver to handle
SDTR, WDTR and any other type of extended message it chooses too. This
makes the sequencer code much simpler, makes extended message handling
debuggable since the bulk of the work is in the kernel driver, and saves
lots of instruction space.
Regen microcode header file.
dev/ic/aic7xxx.c, dev/ic/aic7xxxvar.h:
Add code to handle WDTR and SDTR negotiation in light of the changes in
the message interface to the sequencer. Don't reject targets that
negotiate async by sending an SDTR with a 0 offset. Use an sdtr message
with 0,0 to negotiate async when a target suggests a period that is too
long for us to handle. Some tape and cdrom drives don't like us doing
the message reject that we did in the past.
Fix a problem with handing the QUEUE FULL condition.
Fix a race condition (most likely the cause of the SCB paging problems) that
might allow the sequencer to get unpaused before the condition that caused
it to be paused (a SEQINT) was handled.
Race condition pointed out by Doug Ledford <dledford@dialnet.net> and
by "Dan Willis" <dan@plutotech.com>.
dev/pci/ahc_pci.c:
Add support for the 2940AU, an aic7860 based controller.
dev/pci/pcidevs.h, dev/pci/pcidevs_data.h:
Add product IDs for the 2940AU, aic7860 and aic7855.
Regen data file.
scsi/scsi_message.h:
Add MSG_EXT_SDTR_LEN and MSG_EXT_WDTR_LEN - the length of bytes in these
extended messages.
Thanks to Chuck Cranor <chuck@maria.wustl.edu> for testing these changes
out for me.
2441, and part of 2600. 2436 is left open to remind me that Chris's
comments are probably correct. This file should be built statically and
committed to the tree, not built on a per-kernel basis.
bouyer