have sys/net/route.c:rtrequest1(), which takes rt_addrinfo * as the argument.
pass rt_addrinfo all the way down to rtrequest, and ifa->ifa_rtrequest.
3rd arg of ifa->ifa_rtrequest is now rt_addrinfo * instead of sockaddr *
(almost noone is using it anyways).
benefit: the follwoing command now works. previously we need two route(8)
invocations, "add" then "change".
# route add -inet6 default ::1 -ifp gif0
remove unsafe typecast in rtrequest(), from rtentry * to sockaddr *. it was
introduced by 4.3BSD-reno and never corrected.
XXX is eon_rtrequest() change correct regarding to 3rd arg?
eon_rtrequest() and rtrequest() were incorrect since 4.3BSD-reno,
so i do not have correct answer in the source code.
someone with more clue about netiso-over-ip, please help.
the link level name for the interface (ifp->if_sadl) is allocated
before ifp->if_addrlen is initialized, which could lead to allocating
too little space for the link level address.
Do this by splitting allocation of the link level name out of
if_attach() and into if_alloc_sadl(), which is normally called
by functions like ether_ifattach(). Network interfaces which
don't have a link-specific attach routine must call if_alloc_sadl()
themselves (example: gif).
Link level names are freed by if_free_sadl(), which can be called
from e.g. ether_ifdetach(). Drivers never need call if_free_sadl()
themselves as if_detach() will do it if it is not already done.
While here, add the ability to pass an AF_LINK address to
SIOCSIFADDR in ether_ioctl() (this is what caused me to notice
the problem that the above fixes).
by interface index. if the interface address specified is in 0.0.0.0/8
it will be considered as interface index in network byteorder.
getsockopt(IP_MULTICAST_IF) preserves old behavior if
setsockopt(IP_MULTICAST_IF) was done with interface address, and
returns interface index if setsockopt(IP_MULTICAST_IF) was done with
interface index (again using the form in 0.0.0.0/8).
Suggested by Dave Thaler, based on RIPv2 MIB spec (RFC1724 section 3.3).
http://mail-index.netbsd.org/tech-net/2001/01/13/0003.html
"key" and a "dlt", use a "type" (PFIL_TYPE_{AF,IFNET} for now) and
a val/ptr appropriate for that type. This allows for more future
flexibility with the pfil_hook mechanism.
mandatory for IPv6 (so we can't just validate by using connected pcb - we need
to allow traffic from unconnected pcb to do pmtud).
- if the traffic is validated by xx_ctlinput, allow up to "hiwat" pmtud
route entries.
- if the traffic was not validated by xx_ctlinput, allow up to "lowat" pmtud
route entries (there's upper limit, so bad guys cannot blow up our routing
table).
sync with kame
XXX need to think again about default hiwat/lowat value.
XXX victim selection to help starvation case
- All packets are passed to PFIL_HOOKS as they come off the wire, i.e.
fields in protocol headers in network order, etc.
- Allow for multiple hooks to be registered, using a "key" and a "dlt".
The "dlt" is a BPF data link type, indicating what type of header is
present.
- INET and INET6 register with key == AF_INET or AF_INET6, and
dlt == DLT_RAW.
- PFIL_HOOKS now take an argument for the filter hook, and mbuf **,
an ifnet *, and a direction (PFIL_IN or PFIL_OUT), thus making them
less IP (really, IP Filter) centric.
Maintain compatibility with IP Filter by adding wrapper functions for
IP Filter.
Current status:
Only OHCI chip is supported (fwohci).
ping (IPv4) works with Sony's implementation (SmartConnect) on Win98.
sometimes works but not stable.
Not implemented yet:
IRM (Isochronous Resource Manager) functionality.
Link layer fragmentation.
Topology map.
More to do:
clean ups
MCAP
charactor device part
dhcp
There is no entry in GENERIC config file yet.
Follow sys/dev/ieee1394/IMPLEMENTATION to enable if_fw.
TODO: udp6, and sendto consideration. as pmtud is mandatory for IPv6,
it is rather important for us to support those cases.
TODO: more testing
TODO: kame sync
entering rtentry's for hosts we're not actually communicating
with.
Do this by invoking the ctlinput for the protocol, which is
responsible for validating the ICMP message:
* TCP -- Lookup the connection based on the address/port
pairs in the ICMP message.
* AH/ESP -- Lookup the SA based on the SPI in the ICMP message.
If validation succeeds, ctlinput is responsible for calling
icmp_mtudisc(). icmp_mtudisc() then invokes callbacks registered
by protocols (such as TCP) which want to take some sort of special
action when a path's MTU changes. For TCP, this is where we now
refresh cached routes and re-enter slow-start.
As a side-effect, this fixes the problem where TCP would not be
notified when a path's MTU changed if AH/ESP were being used.
XXX Note, this is only a fix for the IPv4 case. For the IPv6
XXX case, we need to wait for the KAME folks.
Reviewed by sommerfeld@netbsd.org and itojun@netbsd.org.
ip_output(). This flag, if set, causes ip_output() to set
DF in the IP header if the MTU in the route is not locked.
This allows a bunch of redundant code, which I was never
really all that happy about adding in the first place, to
be eliminated.
Inspired by a similar change made by provos@openbsd.org when
he integrated NetBSD's Path MTU Discovery code into OpenBSD.
packets. PR 11082.
This is a short-term workaround. whenever new ipfilter comes out with
proper non-IPv4 support, we should migrate to the new ipfilter.
each in_ifaddr and delete it when an address is purged.
- Don't simply try to delete a multicast address record listed in the
ia_multiaddrs. It results a dangling pointer. Let who holds a
reference to it to delete it.
- when all the interface address is removed from an interface, and there's
multicast groups still left joined, keep it in kludge table.
- when an interface address is added again, recover multicast groups from
kludge table.
this will avoid problem with dangling in_ifaddr on pcmcia card removal,
due to the link from multicast group info (in_multi).
the code is basically from sys/netinet6/in6.c (jinmei@kame).
pointed out by: Shiva Shenoy <shiva_s@yahoo.com>
Without this, if a v6 address is placed before a v4 address in if_addrlist,
a PRU_PURGEIF request for v6 tcp protocol purges also v4 addresses and,
as a result, if_detach fails to request PRU_PURGEIF for v4 protocols
other than tcp.
itojun