the address of the desired PTE location is readily available in the
callers context (setpte4m() retraces the entire 3-level structure
to arrive at the PTE location).
Also, in many cases we can do away with the distinction between pmaps
that have or have not allocated a context. This is really only useful
in cases where we're interested in the REF or MOD bits which can differ
in the TLB version of a PTE. By doing this, we avoid getpte()'s which
in many cases instruct the MMU to start a table walk only to find out
that there's nothing there after going 2/3 of the way, or waste a TLB
entry because of TLB flushing soon after getpte() completes.
In addition, there's a hook to flush the cache line corresponding to
the (kernel virtual) location of a PTE entry when it gets altered.
Anne Hutton <hutton@isi.edu>]:
- add support for Adaptec 155 PCI ATM cards (e.g. ANA-5940)
- add sc->is_adaptec to handle differences between cards.
- break out MID_MK_TXQ/MID_MK_RXQ seperate macros to handle
the new Adaptec format TXQ/RXQ.
- adjust en_dqneed to return 1 on ADP (since the Adaptec can
DMA anything in one DRQ/DTQ!)
- add hook for a bus specific reset function (adaptec has
a seperate reset register that needs to be hit when
resettting the midway).
- adjust DMA test to not worry about burst sizes on the
adaptec (since it handles it all for us!) and to handle
the new DTQ/DRQ format.
- add Adaptec DMA support to en_txlaunch() and en_service()
BUG FIXES:
- fixed receiver panic under heavy load ("lost mbuf in slot 0!").
when the reassembly buffer overflows, the T-bit is set in
the RDB and the data field is empty. en_service() sets up
a 4-byte (RDB size) dummy DMA without IF_ENQUEUE. but the
recv intr handling in en_intr() always does IF_DEQUEUE.
as a result, a successive recv intr loses its mbuf and
leads to a panic. the solution is to only IF_DEQUEUE if
the interrupt has non-zero length (indicating that there
is an mbuf to get). in order for this to work, EN_DQ_MK
must always be non-zero. we do this by or'ing in an unused
bit (0x80000).
reported by: Kenjiro Cho <kjc@csl.sony.co.jp>
- fix setting of transmit channel when txspeed[] is non-zero
(e.g. traffic shaping). the old scheme didn't work
properly (it allowed the same VCI to use multiple tx channels
thus defeating the txspeed[] parameter). the new scheme
statically assigns a VC to a channel when txspeed[] is set.
[note that the code to set txspeed[] isn't in the driver right
now since a MI interface to do this hasn't been made yet]
we add sc->txvc2slot[] and sc->txslot[n].nref for this.
reported by: Kenjiro Cho <kjc@csl.sony.co.jp>,
Milind M Buddihikot <milind@ccrc.wustl.edu>,
Dong Lin <dong@eecs.harvard.edu>
- when doing SRAM copies, be sure to round up the length to the next
largest word (otherwise the driver will try to do a byte clean
up DMA and then get an ID error interrupt).
MINOR CLEANUPS:
- clean up loops in DMA test
contributed by: Kenjiro Cho <kjc@csl.sony.co.jp>
- restructure and cleanup of en_read/en_write macros/inlines
- clean up some byte ordering stuff so that we are consistant throughout
the driver
correspond to the ANA numbers... certainly includes ANA-5940.
- add Efficient Nets product 0x0000. according to linux pci.h
the 0x0000 is an FPGA version of the midway card and the 0x0002
is the ASIC version.
- Indent some comments appropriately per KNF.
- Output all diagnostics using the device name rather than a static string.
- Fix a (mostly marmless) bug in snintr(), where loss of heartbeat wasn't
properly ignored and could mask the `receive descriptors exhausted'
diagnostic.
