anything that might cause an interrupt (e.g. the SCSI bus reset in
ncr53c9x_attach()). If we don't do this, the initial interrupt is
lost, thus causing the state machine to never enter IDLE state, thus
causing SCSI commands to never be executed.
Fixes kern/8544, reported by Erik Bertelsen <erik@mediator.uni-c.dk>.
- Add initial IOP support. ADB doesn't work yet for me, but it's here so
that others will be encouraged to work on it. ADB_HW_IOP basically
is configured as a NOP so that serial consoles will continue to work.
- Roll via1_intr and via2_intr into the intr.c scheme--this also required
changing rtclock_intr to grovel the stack differently so that hardclock
gets the right arguments and softclock() doesn't get all reentrant.
- Make via1 interrupts parallel to via2 interrupts--handlers get a pass-
through pointer and we can register handlers. Register via1 interrupt
with intr_establish()--normally level 1, level 6 for A/UX scheme.
- Use intr_establish() to set real via2 interrupt handler instead of the
hacked function pointer.
- Reorganize adb-direct interrupts so that a function call is removed.
- Implement A/UX interrupts for all Quadras right now. We may need to
special case some Quadras, but Linux folks are reporting success on
several models.
- Fix intrnames to be accurate for the normal, PSC, and A/UX interrupt
configurations.
at levels 5 (sound) and 6 (via1) on the Q700.
Raise splhigh when reading and writing registers. It's ugly, but it's
possible that we could get an interrupt from a higher-level source,
causing a re-read of a memory location.
This is not good when, e.g., we are reading the interrupt register.
Ideally, we would just raise splhigh() in ncr53c9x_readregs(), but
that's m.i. code, and it may be expensive on other architectures.
controllers. Supports GCR-encoded disks only (400K and 800K); neither
of the 1.44M formats will work until someone figures out how to drive
the SWIM and its descendants.
This code was written by Hauke Fath, and had only minor touchup (mostly
KNF) by me.
- returned EOPNOTSUPP rather than -1.
- no check for negative offset.
many of these fix potential security problems in these drivers.
XXX XXX XXX
the d_mmap cdev routine should be changed to have a prototype like:
paddr_t (*d_mmap) __P((dev_t, off_t, int));
by someone!
struct scsipi_adapter; they were not used.
Add a scsipi_ioctl entry point to struct scsipi_adapter. This will be
used to issue ioctl commands to the host adapters.
Inspired by PR #6090, from Matt Jacob.
resolves a great many issues, including Performa 58x interrupt handling
and offset displays on some models.
Programs that depend on the old (pre-NetBSD 1.1) grf interface may break.
That's actually a separate issue uncovered by this code, not caused by it.
certain 17" monitors. Change from Michael R. Zucca, PR 4988.
XXX - This can cause problems on system with the DAFB chip which currently
use only a NuBus-based video adapter. In particular, grf devices may not be
attached properly in this case. This unfortunate situation is less annoying
than not having a reasonable console, however. A reasonable, reliable
monitor sense algorithm for the DAFB would resolve the problem.
deal with cheap CD-ROMs and other devices that do not appear to have
any way to enable parity generation. In the future, it might be nice
to have this configurable on a per-device basis with back-to-back
parity errors automatically disabling parity for the device. That
would require some MI changes.
* Handle unaligned and odd-length transfers.
This could probably be handled better in the future.
but is a marked improvement. This takes advantage of a pseudo-DMA hardware
hack of Apple's that exposes a 16-bit register that the Apple-designed
memory controller acts like a DMA controller and handshakes into or out
of the FIFO. Wierd.
Unfortunately, there does not seem to be a good way to determine what
variety of comm-slot card is present in a machine. There is still an
interrupt issue preventing these cards from working--hopefully that will
be ironed out shortly.
thorpej