macppc/hardware
Forgot to put PowerComputing PowerCenter in list of models that can't use
on-board video
macppc/prep
Reword four-key-combo c-o-O-F to imply you need to hold all four down
until the 0 > prompt appears, also a better description of the keys
shuffle System Disk instructions around a little to make more sense
Fix BootVars instruction to "uncheck auto-boot?"
Change '.Dl 0 \*> Ic "..."' to '.No 0 \*> Ic "..."' surrounded by .(disp
Link to new FAQ entries (such as how to use the Open Firmware environment
and instruction for people unfamiliar with MacOS)
Describe how to prepare an MS-DOS filesystem for booting
Be more consistent about "ISO9660"
The NetBSD/macppc boot CD-R image has "partition zero" bootloader and
XCOFF bootloader to work on all models -- this is described better now
Better info on how to netboot OF 1.0.5 systems
Mention that UFS is not currently supported by NetBSD and MacOS < 10
Detab the dhcpd.conf example
Add .To 2 tags for preparation of bootable media subsections
macppc/install
Change '.Dl 0 \*> Ic "..."' to '.No 0 \*> Ic "..."' surrounded by .(disp
Added new and very very useful "Open Firmware boot syntax" section
describing how to determine the OF boot-device and boot-file
Clean up examples of boot commands
Update descriptions of booting problems (some were incorrect)
Add .To 2 tags for OF boot command subsections and common problems
tweaks to the "Quick install for the impatient", particularly changing the
recommendation to MS-DOS floppy with bootloader and kernel instead of
boot floppy image
common/sysinst
add .To 2 tags for macppc-specific sections
common/postinstall
change tlp0 to de0 in description of typical ethernet interface
1. Replace all "groff"'s with $GROFF so the right binary is picked up depending
on new or old toolchain setups and USETOOLS
2. Remove the DESTDIR check where it adds -M. This is pointless as some of the
file in share/tmac have hard coded references to /usr/share/tmac so using the
new ones in $DESTDIR will just point you back into /usr/share anyways...
(the new toolchain has no issue here as it's tmac files all point into
$TOOLDIR. Any old setups should just depend on the local setup instead of
some mix of DESTDIR and old files the -M would have produced).
release notes (and thus missed updating the NetBSD/evbarm notes):
Based on feedback (various), remove the .toc files from CVS,
and instead generate them each and every time (twice!).
Mention how to manually create /dev entries, since the suggested "Re-install
sets" option doesn't automatically do this (leaving the user without
/dev/console)
fleshing-out (and general "how to set up diskless environment"
instructions in the ../common directory).
Supported hardware and setup for the Intel IQ80310 board is written.
I've filled in the supported-hardware bits for the ARM Integrator
board, but someone (HI RICHARD! :-) will need to provide info about
setting up the firmware for booting and typical run-time environments
for this board.
and instead generate them each and every time (twice!).
Based on a suggestion from Alan Barrett, allow setting MAKETOC=no
to permit rebuilding the install notes without regenerating the
.toc files, to allow more speedy debugging of markup changes.
.Te adds an entry at a specified depth and also outputs the entry name
in the output stream, .To "only" adds the entry. .To is necessaary where
markup issues prevent the use of .Te.
all on page one and they add needless clutter. Additionally
doc2html doesn't output a tag for them, so we cannot link to them.
Lower indent level for Ss and Ss2
Add special HTML support: emit an HREF on each TOC line. There's some
nasty kludging with extending the dot-leader tab stop by the width
of the href, but that's life in mdoc2html.
TOCs need to be regenerated, but I'm not going to bother for a while.
This makes it _much_ more user-friendly, as it allows users
to skip to the parts they want easily.
At present, the TOCs are generated files, and can be regenerated
with "make tocs" (probably has to be run twice to account for
the size of the table itself).
TOCs are named INSTALL.{PostScript,ASCII,HTML,more}.toc instead of
INSTALL.{ps,txt,html,more}.toc because that's what \*[format]
expands to.
