follows BSD/OS practice and ucd-snmp code (FreeBSD does it for specific
interfaces only).
was: if_lastchange get updated on every packet transmission/receipt.
now: if_lastchange get updated when IFF_UP is changed.
network interfaces. This works by pre-computing the pseudo-header
checksum and caching it, delaying the actual checksum to ip_output()
if the hardware cannot perform the sum for us. In-bound checksums
can either be fully-checked by hardware, or summed up for final
verification by software. This method was modeled after how this
is done in FreeBSD, although the code is significantly different in
most places.
We don't delay checksums for IPv6/TCP, but we do take advantage of the
cached pseudo-header checksum.
Note: hardware-assisted checksumming defaults to "off". It is
enabled with ifconfig(8). See the manual page for details.
Implement hardware-assisted checksumming on the DP83820 Gigabit Ethernet,
3c90xB/3c90xC 10/100 Ethernet, and Alteon Tigon/Tigon2 Gigabit Ethernet.
have sys/net/route.c:rtrequest1(), which takes rt_addrinfo * as the argument.
pass rt_addrinfo all the way down to rtrequest, and ifa->ifa_rtrequest.
3rd arg of ifa->ifa_rtrequest is now rt_addrinfo * instead of sockaddr *
(almost noone is using it anyways).
benefit: the follwoing command now works. previously we need two route(8)
invocations, "add" then "change".
# route add -inet6 default ::1 -ifp gif0
remove unsafe typecast in rtrequest(), from rtentry * to sockaddr *. it was
introduced by 4.3BSD-reno and never corrected.
XXX is eon_rtrequest() change correct regarding to 3rd arg?
eon_rtrequest() and rtrequest() were incorrect since 4.3BSD-reno,
so i do not have correct answer in the source code.
someone with more clue about netiso-over-ip, please help.
the link level name for the interface (ifp->if_sadl) is allocated
before ifp->if_addrlen is initialized, which could lead to allocating
too little space for the link level address.
Do this by splitting allocation of the link level name out of
if_attach() and into if_alloc_sadl(), which is normally called
by functions like ether_ifattach(). Network interfaces which
don't have a link-specific attach routine must call if_alloc_sadl()
themselves (example: gif).
Link level names are freed by if_free_sadl(), which can be called
from e.g. ether_ifdetach(). Drivers never need call if_free_sadl()
themselves as if_detach() will do it if it is not already done.
While here, add the ability to pass an AF_LINK address to
SIOCSIFADDR in ether_ioctl() (this is what caused me to notice
the problem that the above fixes).
attempting to enable promisc would result in ENETDOWN. Change this to
allow the interface to always be placed in promiscuous mode, regardless
of IFF_UP. When the interface does come up, the IFF_PROMISC flag will
be consulted, and this matches the behavior that disabling promiscuous
mode has.
timeout()/untimeout() API:
- Clients supply callout handle storage, thus eliminating problems of
resource allocation.
- Insertion and removal of callouts is constant time, important as
this facility is used quite a lot in the kernel.
The old timeout()/untimeout() API has been removed from the kernel.
parties can easily know the state of a link.
- Define an interface announcement message for the routing socket so that
routing daemons and other interested parties know when an interface
is attached/detached.
although this version has been changed somewhat:
- reference counting on ifaddrs isn't as complete as Bill's original
work was. This is hard to get right, and we should attack one
protocol at a time.
- This doesn't do reference counting or dynamic allocation of ifnets yet.
- This version introduces a new PRU -- PRU_PURGEADDR, which is used to
purge an ifaddr from a protocol. The old method Bill used didn't work
on all protocols, and it only worked on some because it was Very Lucky.
This mostly works ... i.e. works for my USB Ethernet, except for a dangling
ifaddr reference left by the IPv6 code; have not yet tracked this down.
which can't be handled by netmask, and ifa_ifwithnet() didn't find the
interface associated with an adress if it was in the same block but not with
the same prefix. This prevented 'route add' and atalkd to work properly
with some network configs.
This has been discussed on tech-net some weeks ago.
(Sorry for a big commit, I can't separate this into several pieces...)
Pls check sys/netinet6/TODO and sys/netinet6/IMPLEMENTATION for details.
- sys/kern: do not assume single mbuf, accept chained mbuf on passing
data from userland to kernel (or other way round).
- "midway" ATM card: ATM PVC pseudo device support, like those done in ALTQ
package (ftp://ftp.csl.sony.co.jp/pub/kjc/).
- sys/netinet/tcp*: IPv4/v6 dual stack tcp support.
- sys/netinet/{ip6,icmp6}.h, sys/net/pfkeyv2.h: IETF document assumes those
file to be there so we patch it up.
- sys/netinet: IPsec additions are here and there.
- sys/netinet6/*: most of IPv6 code sits here.
- sys/netkey: IPsec key management code
- dev/pci/pcidevs: regen
In my understanding no code here is subject to export control so it
should be safe.
itojun